Abstract
In the present study aluminium metal matrix composites (Al-MMCs) reinforced with different Wt% (2,3,4,5 and 6) of Silicon carbide (SiC) and hybrid composites of aluminium matrix reinforced with different Wt% (2,3,4,5 and 6) of SiC and constantly adding Boron carbide (B4C) with 2 wt% were fabricated using a cost effective powder metallurgy (PM) method and the mechanical alloying process. Mechanical properties like micro structure, phase analysis, hardness, compression strength, density, porosity and wear were characterized and investigated for the aluminium matrix composite (AMC) samples. Microstructural characterization of sintered samples was performed using a Scanning electron microscope with energy dispersive X-ray analysis. XRD analysis confirmed the peak identification of Aluminium, SiC and B4C particulates in the (Al-MMCs) composites. The hardness values of the composites Al+6wt% SiC and Al+4wt%SiC+2wt%B4C were seen as 20.6% higher than those of pure aluminium matrix. Increase in the hardness of the composite was seen due to grain refinement and resistance to dislocation motion. The existence of SiC particles in Al matrix was seen having the ability to improve the hardness value of the composites. The addition of SiC and B4C reinforcements in the Al matrix alloy has the potential to greatly increase the compressive strength of the AMCs. The density of hybrid composites was seen having a major impact on the influence of SiC and B4C particulates. The wear resistance of the hybrid composites were examined under load range of 5 and 10 N, with sliding speed of 0.1 m/s. The synergistic effect of reinforcing particles was seen as assisting the improvement of wear resistance due to the relative concentration of SiC and B4C. The incorporation of SiC and B4C reinforcements into the Aluminium matrix hybrid composite can substantially increase the hardness, compressive strength, and wear resistance of the composites.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Data Availability
All data generated are analysed during this study are included in this published article.
References
Suhael Ahmed S, Girisha HN (2020) Experimental investigations on mechanical properties of Al7075/TiB2/Gr hybrid composites. Mater Today Proc 46:6041–6044. https://doi.org/10.1016/j.matpr.2021.01.960
Srivyas PD, Charoo MS (2018) Role of fabrication route on the mechanical and tribological behavior of aluminum metal matrix composites - A review. Mater Today Proc 5:20054–20069. https://doi.org/10.1016/j.matpr.2018.06.372
Imran M, Khan ARA (2019) Characterization of Al-7075 metal matrix composites: A review. J Mater Res Technol 8:3347–3356. https://doi.org/10.1016/j.jmrt.2017.10.012
Bodukuri AK, Eswaraiah K, Rajendar K, Sampath V (2016) Fabrication of Al–SiC–B4C metal matrix composite by powder metallurgy technique and evaluating mechanical properties. Perspect Sci 8:428–431. https://doi.org/10.1016/j.pisc.2016.04.096
Arun Prakash J, Shanmughasundaram P (2017) Mechanical and tribological behaviour of aluminium metal matrix composites – an expatiate review. J Mines, Met Fuels 65:69–81
Borgonovo C, Apelian D (2011) Manufacture of aluminum nanocomposites: A critical review. Mater Sci Forum 678:1–22. https://doi.org/10.4028/MSF.678.1
Garg P, Jamwal A, Kumar D et al (2019) Advance research progresses in aluminium matrix composites: manufacturing & applications. J Mater Res Technol 8:4924–4939. https://doi.org/10.1016/j.jmrt.2019.06.028
Park J, Lee J, Jo I et al (2016) Surface modification effects of SiC tile on the wettability and interfacial bond strength of SiC tile/Al7075-SiCp hybrid composites. Surf Coatings Technol 307:399–406. https://doi.org/10.1016/j.surfcoat.2016.09.016
Nair SV, Tien JK, Bates RC (1985) Sic-reinforced aluminium metal matrix composites. Int Met Rev 30:275–290. https://doi.org/10.1179/imtr.1985.30.1.275
Halverson DC, Pyzik AJ, IiA A, Snowden WE (1989) Processing of boron carbide-aluminum composites. J Am Ceram Soc 72:775–780. https://doi.org/10.1111/j.1151-2916.1989.tb06216.x
Zhao N, Nash P, Yang X (2005) The effect of mechanical alloying on SiC distribution and the properties of 6061 aluminum composite. J Mater Process Technol 170:586–592. https://doi.org/10.1016/j.jmatprotec.2005.06.037
Singh J (2016) Fabrication characteristics and tribological behavior of Al/SiC/Gr hybrid aluminum matrix composites: A review. Friction 4:191–207. https://doi.org/10.1007/s40544-016-0116-8
Singh N, Mazumder R, Gupta P, Kumar D (2017) Ceramic matrix composites: Processing techniques and recent advancements. J Mater Environ Sci 8:1654–1660
Fenghong C, Chang C, Zhenyu W et al (2019) Effects of silicon carbide and tungsten carbide in aluminium metal matrix composites. SILICON 11:2625–2632. https://doi.org/10.1007/s12633-018-0051-6
Rahman MH, Al Rashed HMM (2014) Characterization of silicon carbide reinforced aluminum matrix Composites. Procedia Eng 90:103–109. https://doi.org/10.1016/j.proeng.2014.11.821
Fogagnolo JB, Velasco F, Robert MH, Torralba JM (2003) Effect of mechanical alloying on the morphology, microstructure and properties of aluminium matrix composite powders. Mater Sci Eng A 342:131–143. https://doi.org/10.1016/S0921-5093(02)00246-0
Liu J, Zhou B, Xu L et al (2020) Fabrication of SiC reinforced aluminium metal matrix composites through microwave sintering. Mater Res Express 7:125101–125108. https://doi.org/10.1088/2053-1591/abc8bf
Iqbal AKMA, Lim MJ, Nuruzzaman DM (2017) Effect of compaction load and sintering temperature on the mechanical properties of the Al-SiC nano-composite materials. AIP Conf Proc 1901:1–8. https://doi.org/10.1063/1.5010471
Oñoro J, Salvador MD, Cambronero LEG (2009) High-temperature mechanical properties of aluminium alloys reinforced with boron carbide particles. Mater Sci Eng A 499:421–426. https://doi.org/10.1016/j.msea.2008.09.013
Bhowmik A, Dey S, Dey D, Biswas A (2021) Dry sliding wear performance of Al7075/SiC composites by applying grey-fuzzy approach. SILICON 13:3665–3680. https://doi.org/10.1007/s12633-020-00930-3
Surya MS, Prasanthi G (2022) Effect of silicon carbide weight percentage and number of layers on microstructural and mechanical properties of Al7075/SiC functionally graded material. SILICON 14(4):1339–1348
Zhang L, Shi J, Shen C et al (2017) B4C-Al composites fabricated by the powder metallurgy process. Appl Sci 7:8–13. https://doi.org/10.3390/app7101009
Chand S, Chandrasekhar P, Roy S, Singh S (2021) Influence of dispersoid content on compressibility, sinterability and mechanical behaviour of B4C/BN reinforced Al6061 metal matrix hybrid composites fabricated via mechanical alloying. Met Mater Int 27:4841–4853. https://doi.org/10.1007/s12540-020-00739-0
Mohd Bilal Naim Shaikh SA and MAS (2018) Fabrication and characterization of aluminium hybrid composites reinforced with fly ash and silicon carbide through powder metallurgy. Mater Res Express 5:1-21.https://doi.org/10.1088/2053-1591/aab829
Abdizadeh H, Ashuri M, Moghadam PT et al (2011) Improvement in physical and mechanical properties of aluminum/zircon composites fabricated by powder metallurgy method. Mater Des 32:4417–4423. https://doi.org/10.1016/j.matdes.2011.03.071
Shin S, Lee D, Lee YH et al (2019) High temperature mechanical properties and wear performance of B4C/Al7075 metal matrix composites. Metals 9:1–11. https://doi.org/10.3390/met9101108
Soares E, Bouchonneau N, Alves E et al (2021) Microstructure and mechanical properties of AA7075 aluminum alloy fabricated by spark plasma sintering (SPS). Materials (Basel) 14:1–11. https://doi.org/10.3390/ma14020430
Suprapedi, Mulyadi, Sardjono P, Ramlan (2020) Preparation and characterization of alloy Al -SiC made by using powder metallurgy method. AIP Conf Proc 2221:5–11. https://doi.org/10.1063/5.0005086
Sankhla AM, Patel KM, Makhesana MA et al (2022) Effect of mixing method and particle size on hardness and compressive strength of aluminium based metal matrix composite prepared through powder metallurgy route. J Mater Res Technol 18:282–292. https://doi.org/10.1016/j.jmrt.2022.02.094
Canakci A, Varol T (2014) Microstructure and properties of AA7075/Al-SiC composites fabricated using powder metallurgy and hot pressing. Powder Technol 268:72–79. https://doi.org/10.1016/j.powtec.2014.08.016
Varol T, Canakci A (2013) Effect of weight percentage and particle size of B4C reinforcement on physical and mechanical properties of powder metallurgy Al2024-B4C composites. Met Mater Int 19:1227–1234. https://doi.org/10.1007/s12540-013-6014-y
Natrayan L, Santhosh MS, Mohanraj R, Hariharan R (2019) Mechanical and Tribological Behaviour of Al2O3&SiC Reinforced Aluminium Composites Fabricated via Powder Metallurgy. IOP Conf Ser Mater Sci Eng 561:1–7. https://doi.org/10.1088/1757-899X/561/1/012038
Akbarpour MR, Alipour S, Azar FL, Torknik FS (2016) Microstructure and hardness of Al-SiC nanocomposite fabricated through powder metallurgy method. Indian J Sci Technol 9:1–5. https://doi.org/10.17485/ijst/2016/v9i42/101515
Muraliraja R, Arunachalam R, Al-Fori I et al (2019) Development of alumina reinforced aluminum metal matrix composite with enhanced compressive strength through squeeze casting process. Proc Inst Mech Eng Part L J Mater Des Appl 233:307–314. https://doi.org/10.1177/1464420718809516
Narayanaswamy K, Praveen Kumar BS, Shivana S (2015) Development and Evaluation of Tensile and Compression Strength of Al based MMC. IJERT 3:1–3
Zhang J, Shi H, Cai M et al (2009) The dynamic properties of SiCp/Al composites fabricated by spark plasma sintering with powders prepared by mechanical alloying process. Mater Sci Eng A 527:218–224. https://doi.org/10.1016/j.msea.2009.08.067
Arora G, Sharma S (2019) Production of hybrid reinforcement by ball milling for development of aluminium matrix composites. World J Eng 16:357–362. https://doi.org/10.1108/WJE-10-2017-0338
Saxena A, Singh N, Kumar D, Gupta P (2017) Effect of ceramic reinforcement on the properties of metal matrix nanocomposites. Mater Today Proc 4:5561–5570. https://doi.org/10.1016/j.matpr.2017.06.013
Singh G, Goyal S (2018) Microstructure and mechanical behavior of AA6082-T6/SiC/B4C-based aluminum hybrid composites. Part Sci Technol 36:154–161. https://doi.org/10.1080/02726351.2016.1227410
Surya MS (2022) Effect of SiC weight percentage and sintering duration on microstructural and mechanical behaviour of Al6061/SiC composites produced by powder metallurgy technique. SILICON 14(6):2731–2739
Kumar K, Dabade BM, Wankhade LN (2021) Influence of B4C and SiC particles on aluminium metal matrix composites: A brief overview. Mater Today Proc 44:2726–2734. https://doi.org/10.1016/j.matpr.2020.12.697
Bandil K, Vashisth H, Kumar S et al (2019) Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite. J Compos Mater 53:4215–4223. https://doi.org/10.1177/0021998319856679
El-Sayed Seleman MM, Ahmed MMZ, Ataya S (2018) Microstructure and mechanical properties of hot extruded 6016 aluminum alloy/graphite composites. J Mater Sci Technol 34:1580–1591. https://doi.org/10.1016/j.jmst.2018.03.004
Surya MS, Prasanthi G, Kumar AK, Sridhar VK, Gugulothu SK (2021) Optimization of tribological properties of powder metallurgy-processed Aluminum 7075/SiC composites using ANOVA and artificial neural networks. J Bio Tribo-Corros 7(4):1–12
Kumar GBV, Rao CSP, Selvaraj N (2012) Mechanical and dry sliding wear behavior of Al7075 alloy-reinforced with SiC particles. J Compos Mater 46:1201–1209. https://doi.org/10.1177/0021998311414948
Kumar A, Yeasin Arafath M, Gupta P et al (2020) Microstructural and mechano-tribological behavior of Al reinforced SiC-TiC hybrid metal matrix composite. Mater Today Proc 21:1417–1420. https://doi.org/10.1016/j.matpr.2019.08.186
Akbarpour MR, Alipour S (2018) Microstructure and tribological properties of nanostructured aluminum reinforced with SiC nanoparticles fabricated by powder metallurgy route. Trans Indian Inst Met 71:745–752. https://doi.org/10.1007/s12666-017-1207-6
Sridhar A, Lakshmi KP, Raju CH (2022) Microstructure, mechanical and tribological properties of Al7075/SiC/Graphite hybrid metal matrix composites. J Bio Tribo-Corros 8(3):1–15
Gupta P, Kumar D, Parkash O et al (2018) Dependence of wear behavior on sintering mechanism for Iron-Alumina Metal Matrix Nanocomposites. Mater Chem Phys 220:441–448. https://doi.org/10.1016/j.matchemphys.2018.08.079
Uthayakumar M, Aravindan S, Rajkumar K (2013) Wear performance of Al-SiC-B4C hybrid composites under dry sliding conditions. Mater Des 47:456–464. https://doi.org/10.1016/j.matdes.2012.11.0
Sharifi EM, Karimzadeh F (2011) Wear behavior of aluminum matrix hybrid nanocomposites fabricated by powder metallurgy. Wear 271:1072–1079. https://doi.org/10.1016/j.wear.2011.05.015
Acknowledgements
The authors would like to thank VIT University for providing the facilities for this research.
Funding
The author(s) received no financial support for the research, authorship, and/or publication of this article.
Author information
Authors and Affiliations
Contributions
Mr. P Bharathi: designed the concept, interpreted the data and wrote the manuscript; Dr.T Sampath Kumar: analysed and revised the manuscript.
Corresponding author
Ethics declarations
Ethics Approval
Not applicable.
Consent to Participate
Not applicable.
Consent for Publication
The authors declare that the figures and tables used in this manuscript are original and are not published anywhere.
Competing Interests
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Bharathi, P., kumar, T.S. Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route. Silicon 15, 4259–4275 (2023). https://doi.org/10.1007/s12633-023-02347-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12633-023-02347-0