Abstract
In low-density steel, κ-carbides primarily precipitate in the form of nanoscale particles within austenite grains. However, their precipitation within ferrite matrix grains has not been comprehensively explored, and the second-phase evolution mechanism during aging remains unclear. In this study, the crystallographic characteristics and morphological evolution of κ-carbides in Fe–28Mn–10Al–0.8C (wt%) low-density steel at different aging temperatures and times and the impacts of these changes on the steels’ microhardness and properties were comprehensively analyzed. Under different heat treatment conditions, intragranular κ-carbides exhibited various morphological and crystallographic characteristics, such as acicular, spherical, and short rod-like shapes. At the initial stage of aging, acicular κ-carbides primarily precipitated, accompanied by a few spherical carbides. κ-Carbides grew and coarsened with aging time, the spherical carbides were considerably reduced, and rod-like carbides coarsened. Vickers hardness testing demonstrated that the material’s hardness was affected by the volume fraction, morphology, and size of κ-carbides. Extended aging at higher temperatures led to an increase in carbide size and volume fraction, resulting in a gradual rise in hardness. During deformation, the primary mechanisms for strengthening were dislocation strengthening and second-phase strengthening. Based on these findings, potential strategies for improving material strength are proposed.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
H.T. Lu, D.Z. Li, S.Y. Li, and Y.A. Chen, Hot deformation behavior of Fe–27.34Mn–8.63Al–1.03C lightweight steel, Int. J. Miner. Metall. Mater., 30(2023), No. 4, p. 734.
L.Z. Xie, Z.G. Xu, Y.Z. Qi, J.R. Liang, P. He, Q. Shen, and C.B. Wang, Effect of ball milling time on the microstructure and compressive properties of the Fe–Mn–Al porous steel, Int. J. Miner. Metall. Mater., 30(2023), No. 5, p. 917.
Z.Y. Huang, A.L. Hou, Y.S. Jiang, et al., Rietveld refinement, microstructure, mechanical properties and oxidation characteristics of Fe–28Mn–xAl–1C (x = 10 and 12 wt. %) low-density steels, J. Iron Steel Res. Int., 24(2017), No. 12, p. 1190.
L.L. Wei, G.H. Gao, J. Kim, R.D.K. Misra, C.G. Yang, and X.J. Jin, Ultrahigh strength-high ductility 1GPa low density austenitic steel with ordered precipitation strengthening phase and dynamic slip band refinement, Mater. Sci. Eng. A, 838(2022), art. No. 142829.
D.G. Liu, H. Ding, D. Han, and M.H. Cai, Effect of grain interior and grain boundary κ-carbides on the strain hardening behavior of medium-Mn lightweight steels, Mater. Sci. Eng. A, 871(2023), art. No. 144861.
P. Ren, X.P. Chen, L. Mei, Y.Y. Nie, W.Q. Cao, and Q. Liu, Intragranular brittle precipitates improve strain hardening capability of Fe–30Mn–11Al–1.2C low-density steel, Mater. Sci. Eng. A, 775(2020), art. No. 138984.
S.P. Chen, R. Rana, A. Haldar, and R.K. Ray, Current state of Fe–Mn–Al–C low density steels, Prog. Mater. Sci., 89(2017), p. 345.
Y. Zhang, Z.Z. Zhang, N.V. Medhekar, and L. Bourgeois, Vacancy-tuned precipitation pathways in Al–1.7Cu–0.025In–0.025Sb (at.%) alloy, Acta Mater., 141(2017), p. 341.
J.E. Jin and Y.K. Lee, Effects of Al on microstructure and tensile properties of C-bearing high Mn TWIP steel, Acta Mater., 60(2012), No. 4, p. 1680.
K.T. Park, K.G. Jin, S.H. Han, S.W. Hwang, K. Choi, and C.S. Lee, Stacking fault energy and plastic deformation of fully austenitic high manganese steels: Effect of Al addition, Mater. Sci. Eng. A, 527(2010), No. 16–17, p. 3651.
J.S. Jeong, W. Woo, K.H. Oh, S.K. Kwon, and Y.M. Koo, In situ neutron diffraction study of the microstructure and tensile deformation behavior in Al-added high manganese austenitic steels, Acta Mater., 60(2012), No. 5, p. 2290.
M.J. Yao, E. Welsch, D. Ponge, et al., Strengthening and strain hardening mechanisms in a precipitation-hardened high-Mn lightweight steel, Acta Mater., 140(2017), p. 258.
A. Banis, A. Gomez, A. Dutta, I. Sabirov, and R.H. Petrov, The effect of nano-sized κ-carbides on the mechanical properties of an Fe–Mn–Al–C alloy, Mater. Charact., 205(2023), art. No. 113364.
P. Chen, Q.C. Zhang, F. Zhang, J.H. Du, F. Shi, and X.W. Li, Critical role of κ-carbides in the multi-stage work hardening process of a lightweight austenitic steel, Mater. Charact., 200(2023), art. No. 112853.
P. Dey, R. Nazarov, B. Dutta, et al., Ab initio explanation of disorder and off-stoichiometry in Fe–Mn–Al–C κ carbides, Phys. Rev. B, 95(2017), No. 10, art. No. 104108.
C. Kim, H.U. Hong, J.H. Jang, et al., Reverse partitioning of Al from κ-carbide to the γ-matrix upon Ni addition and its strengthening effect in Fe–Mn–Al–C lightweight steel, Mater. Sci. Eng. A, 820(2021), art. No. 141563.
K. Choi, C.H. Seo, H. Lee, et al., Effect of aging on the microstructure and deformation behavior of austenite base light-weight Fe–28Mn–9Al–0.8C steel, Scr. Mater., 63(2010), No. 10, p. 1028.
J. Wang, M.X. Yang, X.L. Wu, and F.P. Yuan, Achieving better synergy of strength and ductility by adjusting size and volume fraction of coherent κ’–carbides in a lightweight steel, Mater. Sci. Eng. A, 857(2022), art. No. 144085.
I. Gutierrez-Urrutia and D. Raabe, Influence of Al content and precipitation state on the mechanical behavior of austenitic high-Mn low-density steels, Scripta Mater., 68(2013), No. 6, p. 343.
C.L. Lin, C.G. Chao, H.Y. Bor, and T.F. Liu, Relationship between microstructures and tensile properties of an Fe–30Mn–8.5Al–2.0C alloy, Mater. Trans., 51(2010), No. 6, p. 1084.
J.L. Zhang, D. Raabe, and C.C. Tasan, Designing duplex, ultrafine-grained Fe–Mn–Al–C steels by tuning phase transformation and recrystallization kinetics, Acta Mater., 141(2017), 374.
H. Wang, C.Y. Wang, J.X. Liang, et al., Effect of alloying content on microstructure and mechanical properties of Fe–Mn–Al–C low-density steels, Mater. Sci. Eng. A, 886(2023), art. No. 145675.
S.W. Park, J.Y. Park, K.M. Cho, et al., Effect of Mn and C on age hardening of Fe–Mn–Al–C lightweight steels, Met. Mater. Int., 25(2019), No. 3, p. 683.
C.Y. Chao, C.N. Hwang, and T.F. Liu, Grain boundary precipitation in an Fe–7.8Al–31.7Mn–0.54C alloy, Scripta Metall. Mater., 28(1993), No. 1, p. 109.
C.Y. Chao, C.N. Hwang, and T.F. Liu, Grain boundary precipitation behaviors in an Fe–9.8Al–28.6Mn–0.8Si–1.0C alloy, Scripta Mater., 34(1996), No. 1, p. 75.
M.C. Li, H. Chang, P.W. Kao, and D. Gan, The effect of Mn and Al contents on the solvus of κ phase in austenitic Fe–Mn–Al–C alloys, Mater. Chem. Phys., 59(1999), No. 1,. 96.
Y.F. Feng, R.B. Song, Z.Z. Pei, R.F. Song, and G.Y. Dou, Effect of aging isothermal time on the microstructure and room-temperature impact toughness of Fe–24.8Mn–7.3Al–1.2C austenitic steel with κ-carbides precipitation, Met. Mater. Int., 24(2018), No. 5, p. 1012.
T.H. Zhang, H.Y. Wei, K. Zhang, et al., Effect of cooling medium on the κ carbide precipitation behavior, microstructure and impact properties of FeMnAlC low-density steel, Mater. Today Commun., 37(2023), art. No. 107084.
L. Xiao, Y.J. Zhou, C.H. Zhang, Y.Y. Wang, X.T. Deng, and Z.D. Wang, Improving impact toughness of Fe–20Mn–9Al–1.5C–2Ni–3Cr low-density steel by optimizing grain boundaries via multi-stage heat treatment without compromising high strength and ductility, J. Mater. Res. Technol., 29(2024), p. 2396.
J. Jeong, C.Y. Lee, I.J. Park, and Y.K. Lee, Isothermal precipitation behavior of κ-carbide in the Fe–9Mn–6Al–0.15C light-weight steel with a multiphase microstructure, J. Alloys Compd., 574(2013), p. 299.
W.C. Cheng, Phase transformations of an Fe–0.85 C–17.9 Mn–7.1 Al austenitic steel after quenching and annealing, JOM, 66(2014), No. 9, p. 1809.
Y.F. An, X.P. Chen, P. Ren, and W.Q. Cao, Ultrastrong and ductile austenitic lightweight steel via ultra-fine grains and heterogeneous B2 precipitates, Mater. Sci. Eng. A, 860(2022), art. No. 144330.
O.A. Zambrano, J. Valdés, L.A. Rodriguez, et al., Elucidating the role of κ-carbides in Fe–Mn–Al–C alloys on abrasion wear, Tribol. Int., 135(2019), p. 421.
J.L. Zhang, Y.S. Jiang, W.S. Zheng, et al., Revisiting the formation mechanism of intragranular κ-carbide in austenite of a Fe–Mn–Al–Cr–C low-density steel, Scripta Mater., 199(2021), art. No. 113836.
N. Kamikawa, K. Sato, G. Miyamoto, et al., Stress–strain behavior of ferrite and bainite with nano-precipitation in low carbon steels, Acta Mater., 83(2015), p. 383.
E. Welsch, D. Ponge, S.M. Hafez Haghighat, et al., Strain hardening by dynamic slip band refinement in a high-Mn light-weight steel, Acta Mater., 116(2016), p. 188.
D. Canadinc, H. Sehitoglu, and H.J. Maier, The role of dense dislocation walls on the deformation response of aluminum alloyed Hadfield steel polycrystals, Mater. Sci. Eng. A, 454–455(2007), p. 662.
Acknowledgement
The research is financially supported by the National Key Research and Development Program of China (No. 2023YFB3711702).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
All authors must declare financial conflicts of interest.
Rights and permissions
About this article
Cite this article
Gao, Y., Zhang, M., Wang, R. et al. Effect of temperature and time on the precipitation of κ-carbides in Fe–28Mn–10Al–0.8C low-density steels: Aging mechanism and its impact on material properties. Int J Miner Metall Mater 31, 2189–2198 (2024). https://doi.org/10.1007/s12613-024-2857-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-024-2857-0