Abstract
The friction coefficient for aluminum alloy 3003 was determined from a specially designed tip test and finite element (FE) simulations. Measured radial tip distance after the tip test was compared to the FE simulations by iteratively changing friction coefficient and the best fitting friction coefficient was determined. To consider strain rate effect on flow stress response during large plastic deformation, a new combined Hollomon- Voce hardening law was proposed. The friction under three different surface conditions was considered by the proposed inverse FE analysis. The results showed that there was obvious strain rate effect on the predicted punch load in the tip test. Moreover, the different friction coefficients were numerically determined for punch/workpiece and die/workpiece interfaces. Two possible causes of this difference were discussed by the analysis on contact normal pressure and slip velocity distributions of the two interfaces.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
J. T. Maximov, G. V. Duncheva, A. P. Anchev, and M. D. Ichkova, Comp. Mater. Sci. 83, 381 (2014).
H. Sofuoglu and J. Rasty, Tribol. Int. 32, 327 (1999).
T. Robinson, H. Ou, and C. G. Armstrong, J. Mater. Process. Tech. 153-154, 54 (2004).
T. Nakamura, N. Bay, and Z. L. Zhang, J. Tribol.-T ASME 119, 501 (1997).
Y. T. Im, O. Vardan, G. Shen, and T. Altan, Cirp Ann.-Manuf. Techn. 37, 225 (1988).
T. Nishimura, T. Sato, and Y. Tada, J. Mater. Process. Tech. 53, 726 (1995).
Y.-T. Im, S.-H. Kang, and J.-S. Cheon, J. Manuf. Sci. E-T. ASME 125, 378 (2003).
S.-H. Kang, J.-H. Lee, J.-S. Cheon, and Y.-T. Im, Int. J. Mech. Sci. 46, 855 (2004).
T. J. Shin, Y. H. Lee, J. T. Yeom, S. H. Chung, S. S. Hong, I. O. Shim, N. K. Park, C. S. Lee, and S. M. Hwang, Comput. Method. Appl. M. 194, 3838 (2005).
J. C. Pierret, A. Rassili, G. Vaneetveld, R. Bigot, and J. Lecomte-Beckers, Int. J. Mater. Form. 3, 763 (2010).
H. Bašic, I. Demirdžic, and S. Muzaferija, Int. J. Numer. Meth. Eng. 62, 475 (2005).
P. Chauviere, K. H. Jung, D. K. Kim, H. C. Lee, S. H. Kang, and Y. T. Im, J. Mech. Sci. Technol. 22, 924 (2008).
J. H. Sung, J. H. Kim, and R. H. Wagoner, Int. J. Plasticity 26, 1746 (2010).
W. F. Hosford and R. M. Caddel, Metal Forming: Mechanics and Metallurgy, pp. 91–92, Prentice-Hall International, Inc. Easnglewood Cliffs, NJ (1983).
J.-H. Cheng, Int. J. Numer. Meth. Eng. 26, 1 (1988).
W. K. Liu, T. Belytschko, and H. Chang, Comput. Method. Appl. M. 58, 227 (1986).
D. J. Benson, Comput. Method. Appl. M. 72, 305 (1989).
C. Kim, J.-U. Lee, F. Barlat, and M.-G. Lee, J. Tribol.-T ASME 136, 021606 (2014).
A. Azushima and H. Kudo, Cirp. Ann.-Manuf. Techn. 44, 209 (1995).
M. Chowdhury, M. Khalil, D. Nuruzzaman, and M. Rahaman, Int. J. Mech. Mechatron. Eng 11, 53 (2011).
H. J. Bong, F. Barlat, J. Lee, M. G. Lee, and J. H. Kim, Met. Mater. Int. 22, 276 (2016).
G. Cai, L. Lang, K. Liu, S. Alexandrov, D. Zhang, X. Yang, and C. Guo, Met. Mater. Int. 21, 365 (2015).
J. C. Jang and S. H. Kim, Korean J. Met. Mater. 53, 618 (2015).
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
About this article
Cite this article
Bong, H.J., Leem, D., Kim, J.H. et al. Practical determination of friction coefficient of Al 3003 for forming of backward extruded part using simple tip test and inverse finite element analysis. Met. Mater. Int. 22, 356–363 (2016). https://doi.org/10.1007/s12540-015-5158-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12540-015-5158-3