Abstract
Sustainable development of groundwater resources in many developing nations like Nigeria is hampered by paucity of information about the resource. Geospatial technology has provided useful information in understanding the distribution of groundwater throughout the world for the purpose of planning, exploration, monitoring and conservation. Numerous studies have integrated remote sensing (RS) and geographical information system (GIS) in the assessment of groundwater potential in different parts of Nigeria. This paper therefore aims to review the literatures and reveal the successes and most importantly the challenges faced by such studies and provide useful recommendations for improvement in future research. A global perspective of advances in the application of geospatial technology to groundwater mapping was first captured from where the strength and weaknesses of the same application in Nigeria in terms of methodology of data extraction, modelling and validation were assessed. The review shows that less than 20 bibliographies are available with about 50% from the south-western part of the country. Few parameters controlling groundwater are often analysed and categorised without any standard. Most models are produced from software packages that do not allow weighting of thematic layers hence cannot incorporate expert judgements. Areas needing urgent attention for improvement include: time of remote sensing data acquisition, methods of parameter extractions, standard GIS software packages used, novel models and comparison between models and the need for model and map validations. Recommendations on country wide coverage of groundwater potential assessment, provision of groundwater monitoring facilities and strict adherence to groundwater development standards were also made.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
The paucity of information on water resources especially in developing countries like Nigeria is one of the major obstacles to sustainable development of the resource. Water is a valuable resource that supports life, ecological diversity and economic development. Its scarcity is a major cause of poverty, hunger, diseases and a significant contributory factor to humanitarian crises (EL-Baz 2008). To saturate the information gap on water resources, Earth observation technologies together with observation of water cycle have been in the past few decades employed to provide reliable and timely water information. Water resources can broadly be divided into surface and groundwater. Surface water (e.g. streams, rivers and lakes) availability is no longer promising. Where available, its quality is threatened by human activities; thus, seeking alternative source in groundwater becomes expedient. Groundwater development is relatively cheaper, takes a shorter time to develop once favourable spots are located, is less susceptible to pollution than surface water sources and has widespread availability (Jha and Chowdary 2007; Talabi and Tijani 2011; Ahmed II et al. 2013).
Several conventional methods exist for the exploration of groundwater which are mainly based on ground surveys (Ganapuram et al. 2009). These methods include geological, geophysical, hydrogeological surveys and drilling (Prasad et al. 2007; Talabi and Tijani 2011) which are considered expensive, time consuming and difficult to carryout in rugged and inaccessible terrains (Bala et al. 1999; Jaiswal et al. 2003) and may not be highly reliable due to assessment of only a few factors that affect the presence of groundwater (Jaiswal et al. 2003). However, the advent of geospatial technology has now provided a cost effective and timely means of groundwater exploration which is applicable even in inaccessible areas (Pradhan 2009; Manap et al. 2013; Nampak et al. 2014). Remote sensing and GIS have become important tools in the field of hydrogeology for assessing, monitoring and conservation of groundwater resources (Prasad et al. 2007; Jasrotia et al. 2012). The National Remote Sensing Agency of India was the first to integrate information from remote sensing and GIS to delineate groundwater recharge potential zones in 1987 (Yeh et al., 2009). Since then, many studies have utilised geospatial technologies to groundwater investigations with impressive results (e.g. Edet et al. 1996; Solomon and Quiel 2005; Hammouri et al. 2012; Razandi et al. 2015). Furthermore, Jha et al. (2007) grouped the application of remote sensing and GIS in hydrogeology into six categories namely, exploration and assessment of groundwater resources, selection of artificial recharge sites, subsurface flow and pollution modelling, groundwater pollution hazard assessment and protection planning, estimation of natural recharge distribution and hydrogeologic data analysis and process monitoring.
Numerous statistical methods/models have gradually been employed with spatial and thematic data in producing groundwater potential zonation and recharge maps. These models can generally be grouped into three: GIS base models using Weighted Index Overlay and Combinations (e.g. Musa et al. 2000; Shaban et al., 2005; Adji and Sejati 2014; Senthil Kumar and Shankar 2014). Probabilistic models using multi-criteria decision analysis (e.g. Fenta et al. 2014; Rahmati et al. 2014), frequency ratio model (e.g. Oh et al. 2011; Razandi et al. 2015; Guru et al. 2017), logistic regression model (e.g. Ozdemir 2011; Pourtaghi and Pourghasemi 2014), Dempster Shafer model (e.g. Nampak et al. 2014; Park et al. 2014), weight of evidence (e.g. Lee et al. 2012a), evidential belief function (e.g. Mogaji et al. 2016) and Machine Learning Models using artificial neural network (e.g. Lee et al. 2012b), boosted regression tree (e.g. Naghibi and Pourghasemi 2015), classification and regression tree (Naghibi and Pourghasemi 2015) and random forest models (Naghibi et al. 2017). Many newer models are continually introduced in groundwater potential mapping such as multivariate adaptive regression spline model (MARS) (Zabihi et al. 2016), maximum entropy model (Rahmati et al. 2016), generalised additive model (GAM) (Falah et al. 2016) and K-nearest neighbour (KNN) model (Naghibi and Dashtpagerdi 2017).
Groundwater potential maps produced from these models based on different parameters influencing the flow and accumulation of groundwater serve as systematic guides to controlled planning, development and management of the resource (Khalil and Mebius 1991). Many Counties and regions of the world have groundwater maps that guide decision makers, planners as well as groundwater managers in the allocation, development and management of the resources (Elbeih 2014). These maps do not exist for many parts of Nigeria as the application of remote sensing and GIS technology in groundwater hydrology has received very little attention hence, low documentation. The reasons for this might not be unconnected to lack of adequate understanding of the role of geospatial technology in the development process, shortage of trained manpower, financial challenges of acquiring remotely sensed data and inadequate hardware and software facilities for image processing (Abiodun 2000). This paper therefore aims to provide a review on the application of remote sensing and GIS technologies to groundwater studies in Nigeria. Such a review is hoped to bring to bare the successes and most importantly the challenges faced by such studies and provide recommendations for improvement.
The study area
Nigeria is situated in West Africa, bordered by Niger Republic in the north, Chad Republic in the northeast, Benin Republic in the west, Cameroon in the east and the Gulf of Guinea in the south (Fig. 1). The terrain is very variable, with mountains in the southeast, hills and plateaux including the Jos Plateau in the centre, lowlands in the south and plains in the north (Tijani et al. 2016). The entire country lies on longitudes 2°50′ to 14°20′E and from latitudes 4°10′ to 13°48′ N, occupying a land area of about 923,768 km2 (Adelana et al. 2008). The climate varies from equatorial in the south to tropical in the centre and arid in the north. Annual rainfall varies from over 4000 mm in the south to less than 250 mm in the north, the national average being 1180 mm. Rainfall is seasonal with a wet season occurring between July and September in the north, extending to between April and November in the delta area (Tijani et al. 2016). The geology can broadly be divided into two major rock types viz. basement complex and sedimentary successions (Akujieze et al. 2003).
Basement complex and fluvio-volcanics comprising metasediments, schists, granites, basalts, gabbros, syenites, trachytes and rhyolites, largely of Precambrian to Tertiary to Recent volcanic. This complex is part of the Pan-African Mobile Belt lying between the West African Craton and the Congo Craton. It covers about 50% of the surface area of the country (Obaje et al., 2005) and outcrops in parts of northwest, northeast, southeast and the largest outcrop is in north central where Younger Granites of Jurassic age with characteristics ring complex structure intruded the basement (Adelana et al. 2008).
Sedimentary basins-rocks of Cretaceous-Tertiary and younger rocks composed mainly of sandstones, sands, silts, clays, shales, mudstones and limestone (Akujieze et al. 2003). This sedimentary succession covering about the remaining land surface of Nigeria is deposited in about eight structural basins (Eduvie 2006) namely, Sokoto basin (North West), Chad basin (North East), Middle Niger (Nupe basin), Anambra basin (South East), Benue basin (Benue trough), Niger Delta basin (South-South), Hadejia basin (West of Chad basin) and Dahomey basin (South Western Coastal basin).
This geological framework is, to a large extent, responsible for the distribution of groundwater in Nigeria (British Geological Survey, 2005; Adelana et al. 2008). There is a large groundwater potential in Nigeria which according to Akujieze et al. (2003) is estimated at 50 million trillion litres/year with annual estimated recharge of about 155.8 billion cubic metres per year. This by far exceeds the surface water resources of the country which is estimated at about 224 trillion litres/year. The two main types of groundwater are pore-type water in sedimentary cover and fissure-type water found in crystalline rocks (Eduvie 2006). In the crystalline basement areas, groundwater availability depends on the development of thick soil overburden (overburden aquifers) or the presence of fractures that are capable of holding water (fractured crystalline aquifers). The groundwater resources here are usually limited and further compounded with challenges of adverse climatic conditions of aridity and semi aridity (Akujieze et al. 2003). The groundwater found in sedimentary deposits is mainly the pore-type, so also the ones found in alluvial deposits where aeolian and fluvial sediments are found. These collectively formed primary aquifers because the water is contained in their primary pore spaces. Among the biggest water bearing sedimentary units are Chad, Kerri-Kerri, Nsukka, Benin and Abeokuta Formations. This is because they are largely formed from sandstones, alluvial deposits and other related arenaceous sedimentary rocks. Shales, clays, limestones are generally poor aquifers due to their argillaceous nature. There is little groundwater in them, and the one found is only confined to their fracture and weathered zones. These rocks only help to confine an aquifer (Eduvie 2006).
Overview of RS and GIS in groundwater potential mapping around the globe
Remote sensing applications to groundwater investigation was realised quite lately because of the obvious reason that groundwater lies in the subsurface and out of reach of remote sensing devices to detect (Elbeih 2014). Its application only started in the 1960s where aerial photographs and satellite images (visible and near infrared) were utilised in groundwater exploration with limited success (Jha et al. 2007). On the other hand, the use of GIS only began in the late 1980s with groundwater flow modelling (Watkins et al. 1996; Jha et al. 2007). Eventually, the use of aerial photographs in groundwater hydrology started to pave way for satellite imagery in the 1980s as advancement in sensor technology provided high-resolution spatial and multi-spectral imageries (Meijerink 1996). High-resolution satellite imageries aided the identification of surface features associated with groundwater storage and recharge such as lineaments (fractures, faults, bedding planes), topographic slope, natural vegetation, geologic landforms, drainage pattern and density etc. (Todd and Mays 2005; Becker 2006). However, satellite imageries are most useful when they are fed into GIS for integration with other datasets and analysed together to discriminate between groundwater promising areas from non-promising ones for further field surveys. Unlike decades ago, several standardised GIS coverages for groundwater hydrology (e.g. ArcGIS, ENVI, Erdas Imaging, SAGA etc) are now available, prompting more advances and diverse modelling types for groundwater. Currently, remote sensing is playing only a trivial role in groundwater potential mapping as very few datasets (lineament and land use) are now extracted from imageries. Bulk of the data now comes from existing database (geological maps, topographic maps, well locations and yields, geo-electric data, drill data etc) where they are integrated in GIS. The current status of RS and GIS applications in groundwater potential mapping around the globe are summarised in Table 1 below.
RS and GIS application to groundwater potential mapping in Nigeria
The use of remote sensing to analyse surface indicators of groundwater dates back to mid 1990s when Edet et al. (1996) applied aerial photographs and radar imagery to delineate areas suitable for groundwater development in Obudu Plateau and Oban Massif, Southeast Nigeria. The use of satellite imagery and GIS came a bit later when Bala et al. (1999) utilised imagery from Landsat-5 TM to extract information on land cover, vegetation lushness and lineament density in ER-Mapper to plot the first groundwater potential map of Dutsin-Ma, Katsina State. Satellite imagery, digital in nature have many advantages over photographs such as its multi-spectral resolution capability and ability to be easily stored and processed by computers (Teewu et al. 2005). In the succeeding years, the country’s first Earth Observation Satellite NigeriaSat-1 was launched in 2003 (Asiyanbola 2014) to among many other objectives, study the country’s environment and its resources. The satellite carries optical imaging payload that provided a 32-m spatial resolution and swath width of about 640 km and uses the green, red and near infra-red bands equivalent to that of Landsat EMT+ bands 2, 3 and 4. One would expect that the satellite launch would usher in more data availability and spark interest among researchers in groundwater hydrology and indeed many other fields. But rather than increase, there seemed to be complete paucity of literature not until about a decade later when few studies began springing up. Till date, only one study had utilised data from NigeriaSat-1 and none from the subsequent satellites launched for application in groundwater potential mapping.
The application of GIS became prominent after the literature inert period and it provided a platform to integrate data from conventional ground based surveys with remote sensing data. Among the revolutionary studies were the work of Talabi and Tijani (2011) and Mogaji et al. (2011) that employed ArcGIS and ENVI, respectively. GIS application also brought about an upsurge in the number of surface indicating parameters analysed for groundwater potential mapping. From only two parameters in the pre GIS era to a maximum of 11 factors have so far being analysed in a single study. However, many of the models produced were seldom validated due to scarcity of well and spring data but quite recently, a number of studies have utilised well yield data for validation while others have adopted other indirect means of validation such as the use of geo-electric data, rock-type distribution (Nwanchukwu et al. 2013) and water column from wells (Akinlalu et al. 2017). At present, a greater number of investigations concentrate in the south-western region, thus emphasising the need for similar studies in other regions of the country. A summary of just about all published literature from Nigeria in presented in Table 2 (Fig. 2).
Parameters of groundwater potential map
Parameters or conditioning factors that influence the movement and storage of groundwater used in preparing potential maps can be divided into two viz. regular and non-regular parameters. The regular parameters are usually extracted from remote sensing imageries and may include lithology, lineament (frequency and density), drainage (pattern and density), geomorphology, land use, land cover, slope angle vegetation index (NDVI) and topography. Non-regular parameters on the other hand are both sourced from remote sensing and ground-based surveys and may comprise parameters such as topographic wetness index (TWI), water divide zone, stream power index (SPI), storagivity, infiltration rate, transmissivity, specific yield, overburden thickness, aquifer thickness, etc. These parameters can be adopted for any study based on interest or the datasets available. However, some parameters are site or region specific as they improve prediction rate for only such sites or region. For instance, Karstic domain parameter was used for a region underlain by carbonate rocks (Shaban et al., 2005). Tropical savannah regions with concentration of epigeal nests constructed by ecosystem engineers can adopt nest locations as a parameter as they are reported to improve dry-land robustness against drought and are even suggested to indicate the presence of groundwater (Bargués Tobella et al. 2014; Mège and Rango 2009).
Parameter extraction methods and common challenges faced by studies in Nigeria
Lineaments
Lineament is the most common and often most important parameter employed in groundwater potential mapping. Lineaments are naturally occurring alignment of soil, topography, stream channels, vegetation or a combination of these features that are visible on remotely sensed imageries (Alagbe et al. 2013). They are long and linear to curvilinear geologic structures (joints, faults and folds) which may be represented on the earth surface as ridge lines, depressions lines, alignment of vegetation and drainage courses. They are a reflection of the subsurface geology of an area and are important in enhancing secondary porosity in rocks thus influencing weathering, soil erosion and groundwater movements (Edet et al. 1996). Some studies have shown high well yields with short distances from lineaments (e.g. Hammouri et al. 2012; Chuma et al. 2013; Senthil Kumar and Shankar 2014) while it was not true for others (e.g. Fashae et al. 2013; Jasrotia et al. 2012). Lineaments are extracted either manually or automatically from imageries. In manual/visual interpretation, lineaments can be drawn by hand on an overlay of an analogue image under the stereoscope (Ramli et al. 2010; Tirén 2010) or on the screen of a computer (Tirén 2010). Drawing by hand has the advantage of being quick and takes a real geologic form while drawing on the screen has the advantage of using the full image resolution (Tirén 2010). However, there are a number of shortcomings associated with manual interpretation. They include subjectivity and non-reproducibility (interpreter bias) and inadequate lineament detection due to direction of illumination (Raghavan et al. 1995; Meijerink 2007; Ramli et al. 2010). Most researchers are aware of these shortcomings and some make mention of them in their work (e.g. Shaban et al. 2005) but measures to address them are not usually employed or not stressed.
To overcome the problem of subjectivity, Tirén (2010) proposed interpretation by multiple (6) observers or multiple times (6) of interpretations be done to get information about uncertainties in the positions and length of the lineaments. The lineaments that occur in at least three to four out of six interpretations are then chosen. On the basis of direction of illumination source, the use of digital elevation data has been shown to offer the possibility of revealing features not apparent in regular satellite images (Raghavan et al. 1995). This is because a digital elevation model (DEM) could be artificially illuminated from any desired direction, which is not possible in optical satellite imagery. This capability is important where the lighting may be in a perpendicular direction in order to enhance any suspected lineament (Ramli et al. 2010). Review has shown that no study had taken extra step to lessen interpreter bias and only a few studies overcame the second challenge by draping DEM on already processed image for the extraction of lineaments (Mogaji et al. 2011; Bayowa et al. 2014b; Ejepu et al. 2017).
In automatic interpretation, there is the elimination of subjectivity as it uses computer algorithms (Meijerink 2007; Ramli et al. 2010) such as Hough transform (Karnieli et al., 1996) and extraction algorithm of PCI geomatica. However, the major problem is that such algorithms operate purely on linearity contrast in an image. Thus, many features not associated with fractures, such as man-made boundaries (field boundaries, roads, fences, etc.), strike ridges, foliation directions and so on, are included. This leaves the interpreter with the task of establishing one after the other which lineaments are associated with possible fractures and which are not (Meijerink 2007). This requires the interpreter to have a good knowledge of the study area. In recognition of the tedious nature of filtering out false lineaments, only a few studies adopted automatic interpretation (Sikakwe et al., 2015; Akinwumiju et al. 2016). Another possible reason might be the absence of automatic linearity extraction from regular image processing softwares as most of the programs are in standalone softwares with PCI Geomatica being about the only exception (Ramli et al. 2010). This explains why most of the studies that utilised automatic interpretation made use of the line module of PCI Geomatica.
Drainage
Drainage is an important agent of hydrogeological control. Drainage patterns are reflections of surface and subsurface formations (Jaiswal et al. 2003; Prasad et al. 2007), while drainage density is an inverse function of permeability where generally, high drainage density implies low void ratio and consequently low rate of infiltration and vice versa (Murthy 2000; Jaiswal et al. 2003). In comparing different formations or localities, the one that contains the greatest drainage density is usually less permeable and indicates a poorer groundwater potential (Edet et al. 1996). However, Sener et al. (2005) and Shaban et al. (2005) showed that not all high drainage density areas have low infiltration or recharge rate and as such, great care should be exercised in the categorisation.
Drainage, like lineaments, can be extracted manually or automatically from remotely sensed images (Shaban et al. 2005), but review has shown that studies prefer to extract the drainage manually either from topographic maps, aerial photos, satellite images, digital elevation model (DEM) or a combination of these. This is probably because of the same challenges associated with automatic lineament extraction and coupled with the fact that drainage network is much easier to interpret manually especially with familiarity of the area of study. Usually, researchers grid their maps when calculating drainage density and frequency, while few others use sliding windows (frames of specific area) (Shaban et al. 2005). From each grid or frame, the drainage lines are measured and converted to the map scale to arrive at the drainage length. The drainage length is then divided by the area of the grid or frame to arrive at the drainage density. A drainage density map is prepared to indicate areas of high and low density. The importance of drainage density as a controlling factor to groundwater infiltration process is reflected in many studies. Only few studies, Mogaji et al. (2011) and Alagbe et al. (2013), ignored this important parameter.
Lithology
The pattern, texture and density of drainage as well as that of lineaments are controlled by the underlying lithology (Edet et al. 1996). Remote sensing provides an easy and cheap way to map the geology of an area by visually tracing many lithological patches and their boundaries. However, this must be combined with ground truth, providing additions or corrections to the image earlier interpreted. The most common satellite imageries utilised for mapping lithology are the Landsat series with standard colour composite combining bands 1, 4 and 5 (Solomon and Quiel 2005) and bands 7, 4 and 1 (Sener et al., 2005), IRS (LISS) IV combining standard colour composites of bands 1, 4 and 5 (Rajaveni et al. 2015) and aerial photographs for their stereoscopic effect (Yeh et al., 2009). Despite the higher spatial resolution of NigeriaSat-2 (5 m multispectral and 2.5 m panchromatic) compared to Landsat ETM (30 m multispectral and 15 m panchromatic) and IRS (multispectral ranging from 5.8 to 56 m), no research from Nigeria utilised imageries from the Nigeria satellite for this purpose. However, as most regions of the world have been covered with geological surveys, researchers prefer to use digitised maps provided from such surveys.
Geomorphology
Geomorphology here refers to the various landforms and topographical features that are important in planning and execution of groundwater exploration (Fashae et al. 2013). Changes in surface topography affect the depth to the water table and direction of groundwater movement, rainfall intensity and consequently, affect the permeability, porosity and infiltration rates (Al-Abadi and Al-Shamma’a 2014). Geomorphology is very important as it is found to be the most influential factor in a number of studies (Jasrotia et al. 2007; Sajjad et al. 2014). How landform is categorised depends on the structural complexity of the study area, but is generally divided into high lands, plains and low lands, with low lands having better prospect to store groundwater (Teixeira et al. 2008). Landforms are delineated manually from visual interpretations of topographical maps, aerial photographs, satellite imageries, digital elevation models or their combination. Best results are obtained from a combination of either digitised topographic map or ortho-rectified aerial photographs or satellite image with a digital elevation model to achieve a 3D visualisation. This improves the understanding of the spatial relationships between image texture and topography thus allowing land features to be observed from vertical view at different scales and from different orientations (Mohamad et al. 2005). Only seven studies considered geomorphology and is either interpreted from DEM or satellite images with only four of the studies combining both DEM and imagery for better result (Talabi and Tijani 2011; Fashae et al. 2013; Sikakwe et al. 2015; Ejepu et al. 2015; Adewumi and Anifowose 2017).
Slope
Slope measured in degree or percent refers to the rate of change in height across a surface region (Manjare 2014). It influences the infiltration or otherwise of surface water into the subsurface (Manjare 2014; Fenta et al. 2014). Flat to gentle slope areas provide more time for water to remain on the surface thereby promoting infiltration, whereas high slope areas allow lesser residence time of water on the surface resulting in runoff and low infiltration (Sener et al., 2005; Hammouri et al. 2012; Fashae et al. 2013). Slope can be extracted either from digital elevation models (e.g. ASTER and STRM DEMs) (Jasrotia et al. 2012; Deepika et al. 2013; Fashae et al. 2013; Sikakwe et al. 2015) or from topographical contours and survey base points from where a DEM can be generated (Pradhan, 2009; Razandi et al. 2015). After extraction, slope gradient is categorised into different classes ranging from nearly flat level to very steep slope depending on the study choices, but one of the most suitable classification is that standardised classification according to Integrated Mission for Sustainable Development Technical Guidelines (IMSD) India (Manjare 2014) and Ministry of Natural Resources and Environment (NRE), Malaysia. These classifications group slope gradient into about six classes namely, nearly flat level (0–5°), very gentle slope (10–15°) gently sloping (15–25°), moderately sloping (25–35°), strongly sloping (35–60°) and very steep slope (61–90°).
Studies in Nigeria seldom use the slope factor, and when used, the classification is according to study choice (4–5 classes are commonly used) as no guideline classification is reported for Nigeria.
Land use/land cover
Land use/land cover pattern is a significant factor that control infiltration and runoff (Shaban et al. 2005; Kumar et al. 2010). Agricultural and plantation lands for example could be excellent sites for groundwater exploration (Sajjad et al. 2014), as trees and plants can trap water on foliage causing it to infiltrate through the roots to recharge groundwater. Also, Bargues Tobella et al. (2014) revealed that surface water flow preferentially under trees and that could enhance greater infiltration. Settlements on the other hand serve as poor groundwater areas due to the use of concrete floors that only allows surface runoff (Sikakwe et al. 2015). Land use/land cover pattern is usually mapped from remotely sensed data and a combination of topographic map and field verification. Using satellite imagery, a false colour composite (FCC) is usually generated using various band combinations such as IRS bands 1, 2 and 3 (Pradhan, 2009), and Landsat ETM bands 4, 3 and 2 (Fashae et al. 2013; Fenta et al. 2014; Chuma et al. 2013). This is followed by visual identification of the land use/land cover pattern after which training sites are selected for supervised classification. In other cases, studies employ land use/land cover maps already prepared by government agencies only to digitise them and make appropriate classification (Pinto et al. 2015). Only five studies recognised the importance of land use/land cover in this regard (Fashae et al. 2013; Sikakwe et al. 2015; Ejepu et al. 2015; Adewumi and Anifowose 2017). These studies interpreted the land use/land cover patterns from Landsat imageries as ready-made copies are not common and not readily available except probably for major cities like Abuja and Lagos.
Weight assignment
Weight can be said to be the strength or relative degree of importance of one parameter/thematic layer over another or a class under a parameter over another as regards their influence to groundwater storage. There is currently no standard weights for parameters and their classes (Saraf and Choudhary, 1998) as such many studies assign weights based on their judgements. This creates room for assumptions and human bias. Efforts are made by other studies to limit self-judgement by incorporating views of several experts in what is referred to as knowledge-driven approach, others by measuring the relative major and minor interrelationship of one parameter over another (Shaban et al. 2005; Akinwumiju et al. 2016). Another approach that has gained acceptability because of its ability to eliminate human bias is the Multi-criteria Decision Analysis (MCDA). The MCDA is an advanced field in operation research that addresses complex decision problems involving multiple criteria. The commonly used MCDA is the analytical hierarchy process (AHP) developed by Saaty (1980) and less commonly Catastrophe theory (Ahmed et al. 2015). The AHP is the most widely accepted method for scaling rates and weights of parameters/thematic layers and their classes (Fenta et al. 2014) by allowing the decision maker to place his/her judgements in order of priority. In addition, a test of consistency of the judgement is assessed by a consistency ratio (CR) where ratings greater than 0.1 are re-evaluated. The popularity of AHP is probably because it is about the only Multi-criteria Decision Analysis based on GIS. Another method of weight assignment is through literature findings.
A considerable number of studies in Nigeria preferred not to assign weight to thematic layers as wells as classes in the thematic layers. The reason for this might not be unconnected with the type of GIS software used (mostly ILWIS) as it might not provide a platform for weight assignment. However, four weight assigning methods have been adopted. These include personal judgement (Bayowa et al. 2014b; Adewumi and Anifowose 2017), adoption from literature (Talabi and Tijani 2011), major and minor interrelationship of parameters (Akinwumiju et al. 2016) and AHP (Fashae et al. 2013; Ejepu et al. 2015, 2017).
Remote sensing-GIS integration methods
Gao (2002) summarised the methods used in integrating remote sensing, GIS and GPS data into four namely; linear models (LM), interactive models (IM), hierarchical models (HM) and complex models (CM). Linear models are most preferred for groundwater potential mapping (Thakur et al. 2016) owing to their non complexity and less data demand even though they could be subjective. The main linear model in use is the GIS-based weighted overlay analysis. However, many studies from Nigeria chose not to weight thematic layers and instead integrate them using only simple overlay. Hierarchical models are now widely accepted using the multi-criteria decision analysis and most popularly the analytical hierarchy process. The major advantage of this model is that it tends to reduce subjectivity in weight assignment and subsequent layer overlay through the contribution of experts judgements.
Statistical models and machine learning models are quite complex and can be categorised under complex models. These models are increasingly been adopted in recent times and include frequency ratio model (e.g. Oh et al. 2011; Razandi et al. 2015; Guru et al. 2017), logistic regression model (e.g. Ozdemir 2011; Pourtaghi and Pourghasemi 2014), Dempster Shafer model (e.g. Nampak et al. 2014; Park et al. 2014), weight of evidence (e.g. Lee et al. 2012a, b), evidential belief function (e.g. Mogaji et al. 2016), artificial neural network (e.g. Lee et al. 2012a, b ), boosted regression tree (e.g. Naghibi and Pourghasemi 2015), classification and regression tree (Naghibi and Pourghasemi 2015), random forest models (e.g. Naghibi and Dashtpagerdi 2017), multivariate adaptive regression spline model (MARS) (Zabihi et al. 2016), maximum entropy model (Rahmati et al. 2016), generalised additive model (GAM) (Falah et al. 2016) and K-nearest neighbour (KNN) model (Naghibi and Dashtpagerdi Naghibi and Dashtpagerdi 2017). These models have been proven to be satisfactory for groundwater potential mapping but nonetheless, require huge data on well and borehole yields and as such cannot be applicable in data scarce areas.
Thematic layer integration is achieved only by simple GIS overlay, weighted overlay analysis and AHP from studies in Nigeria. Probabilistic and machine learning models have never been attempted probably due to non availability of well data. A considerable number of studies utilised GIS software that resulted in creating sharp contrast or edges between boundaries of different potential zones which does not portray a realistic situation.
Model validation
Validation is an important step in a modelling process as without it, the model will lack scientific significance (Chung-Jo and Fabbri, 2003). The most accepted approach to validating groundwater potential map/model is the use of documented well and borehole yields data by overlying it on the model to verify the model result. Descriptive statistical analysis can then be performed to describe the percentage of, for example, high yield wells that fall in the high potential zones and vice versa (Fenta et al. 2014; Pinto et al. 2015). Statistical and graphical methods of validations are increasingly being employed. Some of these methods include receiver operating characteristics (ROC) and success and prediction rate curves. In these methods, the cumulative percentage of the potential map is plotted on x-axis against the percentage of groundwater occurrence on the y-axis. The area under curve (AUC) is then calculated to represent the accuracy of a prediction. These methods have proved to be quite reliable.
Other validation methods used in the absence of well yield data are aquifer thickness, overburden thickness (from VES), static water levels and well water column (e.g. Murthy 2000; Akinlalu et al. 2017). These validation methods, however, are good assumptions for regions without hydrogeological data. Other studies compare their results with that of previous studies (e.g. Shaban et al. 2005). Unfortunately, many investigations in Nigeria failed to provide model validations. From review, only six studies provided validations variously using borehole yields, saturated thickness, water column and borehole depth. Often, statistical approaches are not applied in the analysis.
Conclusion and recommendations
From literature, it is evident that the application of geospatial technology in groundwater studies in Nigeria is not only limited but also lacks standard. Models are produced using insufficient data, unsuitable software applications and in many instances without validations. Reasons can be attributed to various constraints including but not limited to restrictions on RS data (e.g. NigeriaSat imagery), absence or poor facilities and arrangements for data distribution and sharing between agencies and institutions, poor knowledge about the technology itself, inadequate facilities for trainings at undergraduate and graduate levels leading to insufficient skilled manpower, expensive nature of RS and GIS software packages and chronic scarcity of field data on groundwater due to lack of monitoring facilities. These challenges can be resolved when (1) the National Remote Sensing Agency of Nigeria makes available and affordable to the public RS data of NigeriaSat and data from many other satellites and making the acquisition process easy such as can be downloaded via a website to encourage research in this aspect. Imageries of NigeriaSat-2 from the spatial resolution point of view (5 m multispectral and 2.5 m panchromatic) might prove to be better in hydro-geomorphological information extraction compared to Landsat ETM (30 m multispectral and 15 m panchromatic) and IRS (multispectral ranging from 5.8 to 56 m), (2) improving the obsolete and inadequate facilities and providing up-to date software applications and other accessories at educational institutions and training centres and intensify awareness in the proficiency of RS and GIS in the development process, (3) develop groundwater monitoring facilities throughout the country and ensure strict adherence to groundwater development standards for both public and private concerns.
In conclusion, remote sensing has provided useful data on groundwater conditioning factors to complement the conventional invasive field data while GIS on the other hand has provided a platform for integration of data from these two sources to efficiently interpret groundwater conditions cost effectively. With the growing interest among Nigerian researchers, it would be important to make improvements in areas such as (1) quality and time of satellite data acquisition, as some factors controlling groundwater are better interpreted in a particular time or season. This timing is often ignored but Corgne et al. (2010) showed that dry season imagery is most promising for lineament extraction for example, as it is less affected by vegetation cover. (2) Other models should not just be tested but also used to make comparisons as to which are better for potential prediction given the limited data availability. (3) Efforts must be made at validating groundwater potential models to make any scientific sense. Data used for validation purpose have earlier been discussed in this review. Geophysical data from VES soundings are fairly abundant in the country, but no potential assessment study has inferred optimum drill depth for the potential zones. Finally, the groundwater potential of many parts of the country especially the North-eastern part covered largely by sedimentary successions has not been assessed. Efforts should be intensified to cover the whole country. This will enable adequate planning, exploration and management of the precious resource in a sustainable way.
References
Abdullahi BU, Rai JK, Momoh M, Udensi EE (2013) Application of remote sensing and GIS in ground water mapping in some selected localities in Kebbi state, Nigeria. International journal of marine, Atmospheric & Earth. Sciences 1:81–95
Abiodun AA (2000) Development and Utilization of Remote Sens on Africa’s Development OAU/ECA experts Group meeting, Mbabane
Adelana SMA, Olasehinde PI, Bale RB, Vrbka P, Edet AE, Goni IB (2008) An overview of the geology and hydrogeology of Nigeria. In: Adelana SMA, MacDonald AM (eds) Applied groundwater studies in Africa. Taylor & Francis, London, pp 171–197
Adewumi AJ, Anifowose YB (2017) Hydrogeologic characterization of Owo and its environs using remote sensing and GIS. Appl Water Sci 7:2987–3000
Adji TN, Sejati SP (2014) Identification of groundwater potential zones within an area with various geomorphological units by using several field parameters and a GIS approach in Kulon Progo regency, java, Indonesia. Arab J Geosci 7:161–172
Ahmed IIJB, Okunlola IA, Abdullahi IN, Kolawole LL (2013) Assessment of effects of abattoir activities on groundwater quality in part of Keffi, North Central Nigeria. Water Resour 23:72–91
Ahmed K, Shahid S, Harun S (2015) Assessment of groundwater potential zones in an arid region based on catastrophe theory. Earth Sci Inf 8:539–549
Akinwumiju AS, Olorunfemi MO, Afolabi O (2016) GIS-based integrated groundwater potential assessment of Osun Drainage Basin, Southwestern Nigeria. Ife J Sci 18:147–168
Akinlalu AA, Adegbuyiro A, Adiat KAN, Akeredolu BE, Lateef WY (2017) Application of multi-criteria decision analysis in prediction of groundwater resources potential: a case of Oke-Ana, Ilesa area southwestern, Nigeria. NRIAG J Astron Geophys 6:184–200
Akujieze CN, Coker S, Oteze G (2003) Groundwater in Nigeria – a millennium experience – distribution, practice, problems and solutions. Hydrogeol J 11(12):259–274
Al-Abadi A, Al-Shamma’a A (2014) Groundwater potential mapping of the major aquifer in northeastern Missan governorate, south of Iraq by using analytical hierarchy process and GIS. J Environ Earth Sci 4(10):125–150
Alagbe OA, Sunmonu LA, Adabanija MA (2013) Fracture distribution within Bowen University permanent site and its Hydrogeologic implication. Res J Phys Sci 1(3):1–5
Al-Ruzouq R, Shanableh A, Merabtene T (2015) Geomatics for mapping of groundwater potential zones in northern part of the united Arab Emiratis - Sharjah City. ISPRS - International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences, XL-7/W3, 581–586
Amigun JO, Faruwa RA, Komolafe AA (2015) Integrated Landsat imagery and geophysical exploration for groundwater potential evaluation of Okene and its environs, southwestern Nigeria. In J Geosci 6:209–229
Anifowose AYB, Kolawole F (2012) Tectono-Hydrological Study of Akure Metropolis, Southwestern Nigeria. Proceedings of Hydrology for Disaster Management, 106–120. Retrieved from http://www.unaab.edu.ng
Asiyanbola RA (2014) Remote sensing in developing country-Nigeria: an exploration. J Geogr Geol 6(1):110–128. https://doi.org/10.5539/jgg.v6n1p110
Bala AE, Batelaan O, Smedt F (1999) Using Landsat 5 imagery in the assessment of groundwater resources in crystalline rocks around Dutsin-ma, Northwest Nigeria. J Min Geol 36(1):85–92
Bargués-Tobella A, Reese H, Almaw A, Bayala J, Malmer A, Laudon H, Ilstedt U (2014) The effect of trees on preferential flow and soil infiltrability in an agro-forestry parkland in semiarid Burkina Faso. Water Resour Res 50:3342–3354
Bayowa GO, Olorunfemi MO, Akinluyi FO, Ademilua OL (2014a) Integration of Hydrogeophysical and remote sensing data in the assessment of groundwater potential of the basement complex terrain of Ekiti state, Southwestern Nigeria. Ife J Sci 16:353–363
Bayowa GO, Olusola OM, Omowonuola AF, Lawrence AO (2014b) A preliminary assessment of the groundwater potential of Ekiti state, southwestern Nigeria, using Terrain and Satellite Imagery. J Environ Earth Sci 4:33–42
Becker MW (2006) Potential for satellite remote sensing of groundwater. Ground Water 44:306–318
British Geological Survey (2005) Groundwater Programme commissioned report. Keyworth, Nottingham
Chuma C, Orimoogunje OOI, Hlatywayo DJ, Akinyede JO (2013) Application of remote sensing and geographical information Systems in Determining the groundwater potential in the crystalline basement of Bulawayo metropolitan area, Zimbabwe. Adv Remote Sens 2:149–161
Chung-Jo F, Fabbri AG (2003) Validation of spatial prediction models for landslide hazard mapping. Nat Hazards 30(3):451–472
Corgne S, Magagi R, Yergeau M, Sylla D (2010) An integrated approach to hydro-geological lineament mapping of a semi-arid region of West Africa using Radarsat-1 and GIS. R Sens Environ 114:1863–1875
Deepika B, Avinash K, Jayappa KS (2013) Integration of hydrological factors and demarcation of groundwater prospect zones: insights from remote sensing and GIS techniques. Environ Earth Sci 70:1319–1338
Díaz-Alcaide S, Martínez-Santos P, Villarroya F (2017) A commune-level groundwater potential map for the republic of Mali. Water (Switzerland) 9:1–14. https://doi.org/10.3390/w9110839
Edet AE, Okereke CS, Teme SC, Esu EO (1996) Application of remote-sensing data to groundwater exploration: a case study of the Cross River state, southeastern Nigeria. Hydrogeol J 6:394–404
Eduvie MO (2006) Borehole Failures and Groundwater Development in Nigeria: Paper Presented at a National Seminar held on the Occasion of Water Africa Exhibition (Nigeria 2006)
Ejepu SJ, Olasehinde PI, Omar DM, Abdullahi DS, Adebowale TA, Ochimana A (2015) Integration of geology, remote sensing and geographic information system in assessing groundwater potential of Paiko sheet 185 north- Central Nigeria. J Inf Educ Sci Technol 2:145–155
Ejepu J, Olasehinde PI, Okhimamhe A, Okunlola IA (2017) Investigation of hydrogeological structures of Paiko region, north-Central Nigeria using integrated geophysical and remote sensing techniques. Geosciences (Switzerland) 7:1–17
El-Baz F (2008) Remote Sensing of the Earth: Implications for Groundwater in Darfur. Technologies for clean water. https://www.nae.edu/Publications.aspx (accessed on 15 March, 2016)
Elbeih SF (2014) An overview of integrated remote sensing and GIS for groundwater mapping in Egypt. Ain Shams Eng J 6(1):1–15
Falah F, Nejad SG, Rahmati O, Daneshfar M, Zeinivand H (2016) Applicability of generalised additive model in groundwater potential modelling and comparision its performance by bivariate statistical methods. Geocarto Int:1–40
Fashae OA, Tijani MN, Talabi AO, Adedeji OI (2013) Delineation of groundwater potential zones in the crystalline basement terrain of SW-Nigeria: an integrated GIS and remote sensing approach. Appl Water Sci 4(1):19–38. https://doi.org/10.1007/s13201-013-0127-9
Fenta AA, Kifle A, Gebreyohannes T, Hailu G (2014) Spatial analysis of groundwater potential using remote sensing and GIS-based multi-criteria evaluation in Raya Valley, northern Ethiopia. Hydrogeol J 23(1):195–206
Ganapuram S, Kumar GTV, Krishna IVM, Kahya E, Demirel MC (2009) Mapping of groundwater potential zones in the Musi basin using remote sensing data and GIS. Adv Eng Softw 40(7):506–518
Gao J (2002) Integration of GPS with remote sensing and GIS: reality and prospect. Photogramm Eng Remote Sens 68:447–453
Guru B, Seshan K, Bera S (2017) Frequency ratio model for groundwater potential mapping and its sustainable management in cold desert, India. J King Saud Univ - Sci 29:333–347
Hammouri N, El-Naqa A, Barakat M (2012) An integrated approach to groundwater exploration using remote sensing and geographic information system. J Water Resour Prot 4(9):717–724
Hou E, Wang J, Chen W (2017) A comparative study on groundwater spring potential analysis based on statistical index, index of entropy and certainty factors models. Geocarto Int 32(2):1–16
Jaiswal RK, Mukherjee S, Krishnamurthy J, Saxena R (2003) Role of remote sensing and GIS techniques for generation of groundwater prospect zones towards rural development-an approach. Int J Remote Sens 24:993–1008
Jasrotia AS, Kumar R, Saraf AK (2007) Delineation of groundwater recharge sites using integrated remote sensing and GIS in Jammu district, India. Intl J Remote Sens 28(22):5019–5036
Jasrotia AS, Bhagat BD, Kumar A, Kumar R (2012) Remote sensing and GIS approach for delineation of groundwater potential and groundwater quality zones of western Doon Valley, Uttarakhand, India. J Indian Soc Remote Sens 41(2):365–377
Jha MK, Chowdary VM (2007) Challenges of using remote sensing and GIS in developing nations. Hydrogeol J 15(1):197–200
Jha MK, Chowdhury A, Chowdary VM, Peiffer S (2007) Groundwater management and development by integrated remote sensing and geographic information systems: prospects and constraints. Water Resour Manag 21(2):427–467
Karnieli A, Meiseis A, Fisher L, Arkin Y (1996) Automatic extraction and evaluation of geological linear features from digital remote sensing data using a Hough transform. Photogramm Eng Remote Sens 62:525–531
Khalil J, Mebius J (1991) The role of hydrogeological mapping in groundwater development. Water science no. 10, Special issue on the Round Table meeting on planning for groundwater development in arid regions. Cairo: WRC
Kolawole MS, Ishaku JM, Daniel A, Owonipa OD (2016) Lineament mapping and groundwater occurrence within the vicinity of Osara dam, Itakpe-Okene area, north Central Nigeria, using Landsat data. J Geosci Geomatics 4:42–52
Konkul J, Rojborwornwittaya W, Chotpantarat S (2013) Hydrogeologic characteristics and groundwater potentiality mapping using potential surface analysis in the Huay Sai area, Phetchaburi province, Thailand. Geosci J 18:89–103
Kumar MG, Bali R, Agarwal AK (2010) Integration of remote sensing and electrical sounding data for hydrogeological exploration - a case study of Bakhar watershed, India. Hydrol Sci J 54(5):949–960
Lee S, Kim YS, Oh HJ (2012a) Application of a weights-of-evidence method and GIS to regional groundwater productivity potential mapping. J Environ Manag 96(1):91–105
Lee S, Song KY, Kim Y, Park I (2012b) Regional groundwater productivity potential mapping using a geographic information system (GIS) based artificial neural network model. Hydrogeol J 20:1511–1527
Liu T, Yan H, Zhai L (2015) Extract relevant features from DEM for groundwater potential mapping. In International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences, 2015 International Workshop 40:113–119
MacDonald A, Davies J, Calow R, Chilton J (2005) Developing Groundwater: A Guide for Rural Water Supply. ITDG Publishing, Warwickshire CV23 9QZ, UK, 241–270
Manap MA, Sulaiman WNA, Ramli MF, Pradhan B, Surip N (2013) A knowledge-driven GIS modeling technique for groundwater potential mapping at the upper Langat Basin, Malaysia. Arab J Geosci 6:1621–1637
Manjare BS (2014) Identification of groundwater prospecting zones using remote sensing and GIS techniques in upper vena river watersheds Nagpur district, Maharashtra, India 15th Esri India User Conference 2014:1–14
Meijerink AMJ (1996) Remote sensing applications to hydrology: groundwater. Hydrol Sci J 41(4):549–561
Meijerink AMJ (2007) Remote sensing applications to groundwater. IHP-VI, Series on Groundwater No.16. United Nations Educational, Scientific and Cultural Organization
Mège D, Rango T (2009) Permanent groundwater storage in basaltic dyke fractures and termite mound viability. J Afr Earth Sci 57:127–142
Mogaji KA, Aboyeji OS, Omosuyi GO (2011) Mapping of lineaments for groundwater targeting in the basement complex region of Ondo state, Nigeria, using remote sensing and geographic information system (GIS) techniques. Int J Water Resour Environ Eng 3(7):150–160
Mogaji KA, Omosuyi GO, Adelusi AO, Lim HS (2016) Application of GIS-based evidential belief function model to regional groundwater recharge potential zones mapping in Hardrock geologic terrain. Environ Process 3:93–123
Mohamad AM, Mohammad FR, Zakaria M (2005) Terrain features mapping using aerial photographs and digital elevation model (DEM) in the Cameron highlands, Pahang. Geol Soc Malays 51:143–152
Murthy KSR (2000) Groundwater potential in a semi-arid region of Andhra Pradesh: a geographical information system approach. Int J Remote Sens 21(9):1867–1884
Musa KA, Akhir JM, Abdullah I (2000) Groundwater prediction potential zone in Langat Basin using the integration of remote sensing and GIS. http://www.gisdevelopment.net (accessed on 15 March, 2016)
Nag SK, Saha S (2014) Integration of GIS and remote sensing in groundwater investigations: a case study in Gangajalghati block, Bankura District, West Bengal, India. Arab J Sci Eng 39(7):5543–5553
Naghibi SA, Ahmadi K, Daneshi A (2017) Application of support vector machine, random Forest, and genetic algorithm optimized random Forest models in groundwater potential mapping. Water Resour Manag 31:2761–2775
Naghibi SA, Dashtpagerdi MM (2017) Evaluation of four supervised learning methods for groundwater spring potential mapping in Khalkhal region (Iran) using GIS-based features. Hydrogeol J 25:169–189
Naghibi SA, Pourghasemi HR (2015) A comparative assessment between three machine learning models and their performance comparison by bivariate and multivariate statistical methods in groundwater potential mapping. Water Resour Manag 29(14):5217–5236
Nampak H, Pradhan B, Manap MA (2014) Application of GIS based data driven evidential belief function model to predict groundwater potential zonation. J Hydrol 513:283–300
Nejad SG, Falah F, Daneshfar M, Haghizadeh A, Rahmati O (2017) Delineation of groundwater potential zones using remote sensing and GIS-based data-driven models. Geocarto Int 32(2):167–187
Nwachukwu MA, Aslan A, Nwachukwu MI (2013) Application of geographic information system (GIS) in sustainable groundwater development. Imo River Basin Nigeria International Journal of water Resources and Environmental Engineering 5(6):310–320
Obaje NG, Nzegbuna AI, Moumouni A, Ukaonu CE (2005) Geology and Mineral Resources of Nasarawa State. A Monograph of the Department of Geology and Mining, Nasarawa State University, Keffi. 6–19
Oh HJ, Kim YS, Choi JK, Park E, Lee S (2011) GIS mapping of regional probabilistic groundwater potential in the area of Pohang City, Korea. J Hydrol 399(3–4):158–172
Ozdemir A (2011) GIS-based groundwater spring potential mapping in the Sultan Mountains (Konya, Turkey) using frequency ratio, weights of evidence and logistic regression methods and their comparison. J Hydrol 411(3–4):290–308
Park I, Kim Y, Lee S (2014) Groundwater productivity potential mapping using evidential belief function. Ground Water 52:201–207
Park S, Hamm SY, Jeon HT, Kim J (2017) Evaluation of logistic regression and multivariate adaptive regression spline models for groundwater potential mapping using RS and GIS. Sustainability (Switzerland) 9. https://doi.org/10.3390/su9071157
Pinto D, Shrestha S, Babel MS, Ninsawat S (2015) Delineation of groundwater potential zones in the Comoro watershed, Timor Leste using GIS, remote sensing and analytic hierarchy process (AHP) technique. Appl Water Sci 7:503–519. https://doi.org/10.1007/s13201-015-0270-6
Pourtaghi ZS, Pourghasemi HR (2014) GIS-based groundwater spring potential assessment and mapping in the Birjand township, southern Khorasan Province Iran. Hydrogeol J 22(3):643–662
Pradhan B (2009) Groundwater potential zonation for basaltic watersheds using satellite remote sensing data and GIS techniques. Cent Eur J Geosci 1:120–129
Prasad RK, Mondal NC, Banerjee P, Nandakumar MV, Singh VS (2007) Deciphering potential groundwater zone in hard rock through the application of GIS. Environ Geol 55(3):467–475
Raghavan V, Masumoto S, Koike K, Nagano S (1995) Automatic lineament extraction from digital images using a segment tracing and rotation transformation approach. Comput Geosci 21(4):555–591
Rahmati O, Nazari SA, Mahdavi M, Pourghasemi HR, Zeinivand H (2014) Groundwater potential mapping at Kurdistan region of Iran using analytic hierarchy process and GIS. Arab J Geosci 8:1–13. https://doi.org/10.1007/s12517-014-1668-4
Rahmati O, Pourghasemi HR, Melesse AM (2016) Application of GIS-based data driven random forest and maximum entropy models for groundwater potential mapping: a case study at Mehran region, Iran. Catena 137:360–372
Rajaveni SP, Brindha K, Elango L (2015) Geological and geomorphological controls on groundwater occurrence in a hard rock region. Appl Water Sci 7:1377–1389. https://doi.org/10.1007/s13201-015-0327-6
Ramli MF, Yusof N, Yusoff MK, Juahir H, Shafri HZM (2010) Lineament mapping and its application in landslide hazard assessment: a review. Bull Eng Geol Environ 69(2):215–233
Razandi Y, Pourghasemi HR, Neisani NS, Rahmati O (2015) Application of analytical hierarchy process, frequency ratio, and certainty factor models for groundwater potential mapping using GIS. Earth Sci Inf 8(4):867–883
Saaty TL (1980) The analytic hierarchy process: planning, priority setting, resource allocation. McGraw-Hill, New York
Sajjad H, Iqbal M, Bhat FA (2014) Integrating geospatial and geophysical information for deciphering groundwater potential zones in Dudhganga catchment, Kashmir Valley, India. Am J Water Resour 2:18–24
Saraf A, Choudhary PR (1998) Integrated remote sensing and GIS for ground water exploration and identification of artificial recharge site. Int J Remote Sens 19:1825–1841
Sener E, Davraz A, Ozcelik M (2005) An integration of GIS and remote sensing in groundwater investigations: a case study in Burdur, Turkey. Hydrogeol J 13:826–834
Senthil Kumar GR, Shankar K (2014) Assessment of groundwater potential zones using GIS. Frontiers in. Geosciences 2:1–10
Shaban A, Khawlie M, Abdallah C (2005) Use of remote sensing and GIS to determine recharge potential zones: the case of occidental Lebanon. Hydrogeol J 14:433–443
Sikakwe GU, Ntekim EEU, Obi DA, George AM (2015) Geohydrological study of weathered basement aquifers in Oban massif and environs southeastern Nigeria: using remote sensing and geographic information system techniques. IOSR journal of applied geology and. Geophysics 3(2):321–990
Singh P, Thakur JK, Kumar S (2013) Delineating groundwater potential zones in a hard-rock terrain using geospatial tool. Hydrol Sci J 58:213–223
Solomon S, Quiel F (2005) Groundwater study using remote sensing and geographic information systems (GIS) in the central highlands of Eritrea. Hydrogeol J 14:729–741
Tahmassebipoor N, Rahmati O, Noormohamadi F, Lee S (2016) Spatial analysis of groundwater potential using weights-of-evidence and evidential belief function models and remote sensing. Arab J Geosci 9(79):1–18
Talabi AO, Tijani MN (2011) Integrated remote sensing and GIS approach to Ground-water potential assessment in the basement terrain of Ekiti area south-western Nigeria. RMZ—Mater Geoenviron 58(3):303–328
Teixeira J, Chamine HI, Marques JE, Gomes A, Carvalho JM, Alberti AP, Rocha FT (2008) Integrated approach of Hydrogeomorphology and GIS mapping to the evaluation of groundwater resources: an example from the Hydromineral system of Caldas Da Cavaca, NW Portugal. Glob Groundw Res Manag:227–249
Thakur JK, Singh SK, Ekanthalu VS (2016) Integrating remote sensing, geographic information systems and global positioning system techniques with hydrological modeling. Appl Water Sci 7:1595–1608. https://doi.org/10.1007/s13201-016-0384-5
Tijani M, Crane E, Upton K, O-Dochartaigh BE (2016) Africa groundwater atlas: hydrogeology of Nigeria. British geological survey. http://earthwise.bgs.ac.uk/index.php/Hydrogeology_of_Nigeria (accessed 3/5/2016)
Tirén S (2010) Lineament interpretation. Short review and methodology Retrieved from www.stralsakerhetsmyndigheten.se
Todd DK, Mays LW (2005) Groundwater hydrology, 3rd edn. John Wiley & Sons, NJ
Watkins DW, McKinney DC, Maidment DR, Lin MD (1996) Use of geographic information systems in groundwater flow modeling. J Water Resour Plan Manag, ASCE 122(2):88–96
Yeh HF, Lee CH, Hsu KC, Chang PH (2009) GIS for the assessment of the groundwater recharge potential zone. Environ Geol 58:185–195
Zabihi M, Pourghasemi HR, Pourtaghi ZS, Behzadfar M (2016) GIS-based multivariate adaptive regression spline and random forest models for groundwater potential mapping in Iran. Environ Earth Sci 75(8):665. https://doi.org/10.1007/s12665-016-5424-9
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ahmed II, J.B., Mansor, S. Overview of the application of geospatial technology to groundwater potential mapping in Nigeria. Arab J Geosci 11, 504 (2018). https://doi.org/10.1007/s12517-018-3852-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12517-018-3852-4