Abstract
In this study, the floating liner method is utilized to measure the friction generated in the piston assembly of a single-cylinder gasoline engine. The piston assembly is subjected to combustion pressure, lubricating friction, and asperity friction during engine operation and reciprocates within the cylinder. Therefore, the main goal of this study is to investigate the effect of engine combustion and lubricant conditions on piston friction. First, we analyze how the combustion pressure, obtained by changing the combustion load and the ignition timing, affects piston friction. Second, by adjusting engine speed and coolant/oil temperature, we analyze how each condition affects piston friction. Through the experiments for each case, it was confirmed that the friction increased as the combustion pressure increased under the same lubrication conditions. It was also confirmed that the piston friction was significantly measured due to the increase in lubrication friction as the engine speed increased. Finally, it was confirmed that as the temperature decreased, the oil viscosity increased, resulting in a large friction loss.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Aghaali, H. and Ångström, H. E. (2015). A review of turbocompounding as a waste heat recovery system for internal combustion engines. Renewable and Sustainable Energy Reviews, 49, 813–824.
Benajes, J., García, A., Pastor, J. M. and Monsalve-Serrano, J. (2016). Effects of piston bowl geometry on reactivity controlled compression ignition heat transfer and combustion losses at different engine loads. Energy, 98, 64–77.
Carden, P., Bell, D., Priest, M. and Barrell, D. (2006). Piston assembly friction losses: Comparison of measured and predicted data. SAE Paper No. 2006-01-0426.
Delprete, C. and Razavykia, A. (2020). Piston dynamics, lubrication and tribological performance evaluation: A review. Int. J. Engine Research 21, 5, 725–741.
Duarte Forero, J., Valencia Ochoa, G. and Piero Rojas, J. (2020). Effect of the geometric profile of top ring on the tribological characteristics of a low-displacement diesel engine. Lubricants 8, 8, 83.
Grabon, W., Pawlus, P., Wos, S., Koszela, W. and Wieczorowski, M. (2017). Effects of honed cylinder liner surface texture on tribological properties of piston ring-liner assembly in short time tests. Tribology International, 113, 137–148.
Hoshi, M. (1984). Reducing friction losses in automobile engines. Tribology International 17, 4, 185–189.
Jang, S. (2022). Computational study on the frictional power loss reduction of piston ring with laser surface texturing on the cylinder liner. Int. J. Automotive Technology 23, 3, 855–865.
Jiang, Y. K., Zhang, J. P., Hong, G., Wan, L. P. and Liu, X. (2015). 3D EHD lubrication and wear for piston ring-cylinder liner on diesel engines. Int. J. Automotive Technology 16, 1, 1–15.
Krishnan, A. (2014). Simulation of an Engine Friction Strip Test. M. S. Thesis. Chalmers University of Technology. Göteborg, Sweden.
Lee, S., Kim, G. and Bae, C. (2022). Effect of mixture formation mode on the combustion and emission characteristics in a hydrogen direct-injection engine under different load conditions. Applied Thermal Engineering, 209, 118276.
Okamoto, T. and Uchida, N. (2016). New concept for overcoming the trade-off between thermal efficiency, each loss and exhaust emissions in a heavy duty diesel engine. SAE Int. J. Engines 9, 2, 859–867.
Sato, T., Kurita, H., Ito, A. and Iwasaki, H. (2015). Friction measurement of Al−17% Si monolithic cylinder with using newly developed floating liner device. SAE Int. J. Engines 8, 1, 135–142.
Tormos, B., Martín, J., Carreño, R. and Ramírez, L. (2018). A general model to evaluate mechanical losses and auxiliary energy consumption in reciprocating internal combustion engines. Tribology International, 123, 161–179.
Totaro, P. P., Westerfield, Z. and Tian, T. (2016). Introducing a new piston skirt profile to reduce engine friction. SAE Paper No. 2016-01 1046.
Truong, D. Q., Ahn, K. K., Trung, N. T. and Lee, J. S. (2013). Performance analysis of a variable-displacement vane-type oil pump for engine lubrication using a complete mathematical model. Proc. Institution of Mechanical Engineers, Part D: J. Automobile Engineering 227, 10, 1414–1430.
Usman, A. and Park, C. W. (2016). Numerical investigation of frictional behavior and energy loss in mixed-hydrodynamic contact of piston ring pack with deformed cylinder liner during warm-up period of SI-engine. Energy Conversion and Management, 117, 115–131.
Xu, J., Chang, S., Fan, X. and Fan, A. (2016). Effects of electromagnetic intake valve train on gasoline engine intake charging. Applied Thermal Engineering, 96, 708–715.
Yin, B., Zu, J., Xu, B., Huang, G. and Yang, M. (2020). Friction and wear performance of double-bump design of piston skirt main thrust side. Int. J. Automotive Technology 21, 6, 1579–1586.
Zhu, D., Cheng, H. S., Arai, T. and Hamai, K. (1992). A numerical analysis for piston skirts in mixed lubrication — Part I: Basic modeling. J. Tribology 114, 3, 553–562.
Acknowledgement
This work was supported by Hyundai NGV and Hyundai Motor Company.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Kang, J., Cho, J. & Park, S. Investigation of Friction Loss Characteristics of Engine Pistons for Different Engine Operating Conditions. Int.J Automot. Technol. 24, 503–511 (2023). https://doi.org/10.1007/s12239-023-0042-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-023-0042-5