Abstract
This paper discusses the two-phase flow pattern and temperature distribution in a loop thermosyphon as a defrost device at the surface of the evaporator in the refrigerator with different heater locations and different heating power. A computational fluid dynamics (CFD) study was carried out using ANSYS FLUENT 15.0. The volume of fluid (VOF) model was considered to simulate evaporation and condensation at the heater surface using user-defined functions (UDFs). 2D geometries were developed with a heater inserted in the loop thermosyphon. The simulation results were verified using Fadhl’s experimental and numerical temperature data [2]. The maximum difference is 2.4 % between the calculated data and Fadhl’s data. The two-phase flow pattern and the temperature field varied with the different heater locations and heating power values. The thermal performance was evaluated based on the average temperature and temperature uniformity inside the loop thermosyphon.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
B. Fadhl, L. C. Wrobel and H. Jouhara, Numerical modelling of the temperature distribution in a two–phase closed thermosiphon, Applied Thermal Engineering, 60 (2013) 122–131.
B. Fadhl, L. C. Wrobel and H. Jouhara, CFD modelling of a two–phase closed thermosyphon charged with R134a and R404a, Applied Thermal Engineering, 78 (2015) 482–490.
L. M. Poplaski, A. Faghri and T. L. Bergman, Analysis of internal and external thermal resistances of heat pipes including fins using a three–dimensional numerical simulation, International Journal of Heat and Mass Transfer, 102 (2016) 455–469.
S. Lin, J. Broadbent and R. McGlen, Numerical study of heat pipe application in heat recovery systems, Applied Thermal Engineering, 25 (2005) 127–133.
S. Touahri and T. Boufendi, Numerical study of the conjugate heat transfer in a horizontal pipe heated by joulean effect, Thermal Science, 16 (2012) 53–67.
T. Daimaru, S. Yoshida and H. Nagai, Study on thermal cycle in oscillating heat pipes by numerical analysis, Applied Thermal Engineering, 113 (2017) 1219–1227.
W. Qu and H. B. Ma, Theoretical analysis of startup of a pulsating heat pipe, International Journal of Heat and Mass Transfer, 50 (2007) 2309–2316.
K. Kafeel and A. Turan, Simulation of the response of a thermosyphon under pulsed heat input conditions, International Journal of Thermal Sciences, 80 (2014) 33–40.
L. Asmaie, M. Haghshenasfard, A. Mehrabani–Zeinabad and M. N. Esfahany, Thermal performance analysis of nanofluids in a thermosyphon heat pipe using CFD modeling, Heat Mass Transfer, 49 (2013) 667–678.
W. Lian, W. Chang and Y. Xuan, Numerical investigation on flow and thermal features of a rotating heat pipe, Applied Thermal Engineering, 101 (2016) 92–100.
R. Ranjan, J. Y. Murthy, S. V. Garimella and U. Vadakkan, A Numerical model for transport in flat heat pipes considering wick microstructure effects, International Journal of Heat and Mass Transfer, 54 (2011) 153–168.
N. Minocha, J. B. Joshi, A. K. Nayak and P. K. Vijayan, 3D CFD simulation of passive decay heat removal system under boiling conditions: Role of bubble sliding motionon inclined heated tubes, Chemical Engineering Science, 145 (2016) 245–265.
A. S. Annamalai and V. Ramalingam, Experimental investigation and computational fluid dynamics analysis of a air cooled condenser heat pipe, Thermal Science, 15 (2011) 759–772.
S. C. K. D. Schepper, G. J. Heynderickx and G. B. Marin, Modeling the evaporation of a hydrocarbon feedstock in the convection section of a steam cracker, Computers and Chemical Engineering, 33 (2009) 122–132.
A. Alizadehdakhel, M. Rahimi and A. A. Alsairafi, CFD modeling of flow and heat transfer in a thermosyphon, International Communications in Heat and Mass Transfer, 37 (2010) 312–318.
Z. Lin, S. Wang, R. Shirakashi and L. W. Zhang, Simulation of a miniature oscillating heat pipe in bottom heating mode using CFD with unsteady modeling, International Journal of Heat and Mass Transfer, 57 (2013) 642–656.
S. M. Pouryoussefi and Y. Zhang, Numerical investigation of chaotic flow in a 2D closed–loop pulsating heat pipe, Applied Thermal Engineering, 98 (2016) 617–627.
W. Kalata, K. J. Brown and R. J. Schick, Injector study via VOF: Emphasis on vapor condensation due to spray, 23rd Annual Conference on Liquid Atomization and Spray Systems (2011).
W. Lei, L. Yanzhonga, L. Zhan and Z. Kanga, Numerical investigation of thermal distribution and pressurization behavior in helium pressurized cryogenic tank by introducing a multicomponent model, 25th International Cryogenic Conference & International Cryogenic Materials Conference (2014).
Y. U. Gu, D. K. Jeong, J. H. Hwang, Y. H. Kwon and J. S. Kim, Study on defrost of evaporator using bubble jet loop heat pipe as a defrost device, 10th International Heat Pipe Symposium (2011).
ANSYS FLUENT, Theory Guide (Release 15.0). Multiphase Flows, ANSYS, Inc. (2013) 465–600 (chapter 17).
Thermo–physical properties of fluid system, NIST webbook, NIST database, http://webbook.nist.gov/chemistry/fluid/.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Chang Yong Park
Man-Yeong Ha received his B.S. degree from Pusan National University, Korea, in 1981, M.S. degree, in 1983, from Korea Advanced Institute of Science and Technology, Korea, and Ph.D. degree from Pennsylvania State University, USA in 1990. Dr. Ha is currently a Professor at the School of Mechanical Engineering at Pusan National University in Busan, Korea. He serves as an Editor of the Journal of Mechanical Science and Technology. His research interests are focused on thermal management, computational fluid dynamics, and micro/nano fluidics.
Yong Gap Park received his B.S. degree from Pusan National University, Korea, in 2008, and Ph.D. degree from Pusan National University, Korea in 2014. Dr. Park is currently a Research Professor at Rolls-Royce and Pusan National University Technology Centre in Thermal Management, in Busan, Korea. His research interests are focused on natural convection, heat exchanger and computational fluid dynamics.
Seong Hyun Park received her B.S. degree from Pusan National University, Korea, in 2010. He started attending Pusan National University for the integrated Ph.D. program under the supervision of professor Man Yeong Ha. His research interests are focused on numerical simulation on two phase flow with phase change and heat exchanger.
Rights and permissions
About this article
Cite this article
Park, S.H., Kim, Y.S., Kim, S.Y. et al. Numerical study on the two-phase flow pattern and temperature distribution in a loop thermosyphon as a defrost device at the evaporator in the refrigerator. J Mech Sci Technol 32, 5927–5936 (2018). https://doi.org/10.1007/s12206-018-1144-2
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-018-1144-2