Abstract
Compressors consume a considerable portion of the electricity used in the industrial sector. Hence, improvements in compressor efficiency lead to energy savings and reduce environmental impacts. The efficiency of an unshrouded centrifugal compressor suffers from leakage flow over the blade tips. The effect of tip leakage flow on the passage flow differs between the full and splitter blade passages. In this study, the differences in the flow fields between the full and splitter blade passages were studied numerically in detail. An industrial high-speed compressor with a design pressure ratio of 1.78 was modelled. Numerical studies were conducted with six different tip clearances and three different diffuser widths. The results show that increasing tip clearance considerably increases the reversed flow into the impeller with an unpinched diffuser. The reversed flow then partly mixes into the flow in the same blade passage it entered the impeller and the rest migrates over the blade, mixing with the tip clearance flow. Furthermore, as the reversed and clearance flow mix into the wake, the wake is weakened. As pinch reduces both the reversed flow and clearance flow, the passage wakes are stronger with pinches. However, the pinch is beneficial as the losses at the impeller outlet decrease.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
A. de Almeida, P. Fonseca, H. Falkner and P. Bertoldi, Market transformation of energy-efficient motor technologies in the EU, Energy Policy, 31 (2003) 563–575.
R. Saidur, N. Rahim and M. Hasnuzzaman, A review on compressed-air energy use and energy savings, Renewable and Sustainable Energy Reviews, 14 (2010) 1135–1153.
J. Viholainen, K. Grönman, A. Jaatinen-Värri, A. Grönman, P. Ukkonen and M. Luoranen, Centrifugal compressor efficiency improvement and its environmental impact in waste water treatment, Energy Conversion and Management, 101 (2015) 336–342.
R. Pampreen, Small turbomachinery compressor and fan aerodynamics, J. of Engineering for Gas Turbines and Power, 95 (1973) 251–256.
G. Eisenlohr and H. Chladek, Thermal tip clearance control for centrifugal compressor of an APU engine, J. of Turbomachinery, 116 (1994) 629–634.
D. Palmer and W. Waterman, Design and development of an advanced two-stage centrifugal compressor, J. of Turbomachinery, 117 (1995) 205–212.
T. Turunen-Saaresti and A. Jaatinen, Influence of the different design parameters to the centrifugal compressor tip clearance loss, J. of Turbomachinery, 135 (2013) 011017.
J. Backman, A. Reunanen, J. Saari, T. Turunen-Saaresti, P. Sallinen and H. Esa, Effects of impeller tip clearance on centrifugal compressor efficiency, Proceedings of ASME Turbo Expo, Montreal, Canada, May 14-17 (2007) paper no. GT2007-28200.
J. Denton, Loss mechanisms in turbomachines, J. of Turbomachinery, 115 (1993) 621–656.
M. Schleer, S. J. Song and R. S. Abhari, Clearance effects on the onset of instability in a centrifugal compressor, J. of Turbomachinery, 130 (2008) 031002.
M. Zangeneh, M. Schleer, F. Pløger, S. S. Hong, C. Roduner, B. Ribi and R. S. Abhari, Investigation of an inversely designed centrifugal compressor stage-Part I: Design and numerical verification, J. of Turbomachinery, 126 (2004) 73–81.
M. Ishida, Y. Senoo and H. Ueki, Secondary flow due to the tip clearance at the exit of centrifugal impellers, J. of Turbomachinery, 112 (1990) 19–24.
N. Buffaz and I. Trébinjac, Detailed analysis of the flow in the inducer of a transonic centrifugal compressor, J. of Thermal Science, 21 (2002) 1–12.
M. Schleer and R. S. Abhari, Clearance effects on the evolution of the flow in the vaneless diffuser of a centrifugal compressor at part load condition, J. of Turbomachinery, 130 (2008) 031009.
M. Schleer, S. S. Hong, M. Zangeneh, C. Roduner, B. Ribi, F. Pløger and R. S. Abhari, Investigation of an inversely designed centrifugal compressor stage -Part II: Experimental investigations, J. of Turbomachinery, 126 (2004) 82–90.
H.-L. Wang, G. Xi, J.-Y. Li and M.-L. Yuan, Effect of the tip clearance variation on the performance of a centrifugal compressor with considering impeller deformation, Proceedings of the Institution of Mechanical Engineers, Part A: J. of Power and Energy, 225 (2011) 1143–1155.
A. Jaatinen-Värri, A. Grönman, T. Turunen-Saaresti and J. Backman, Investigation of the stage performance and flow fields in centrifugal compressor with a vaneless diffuser, International J. of Rotating Machinery (2014) 139153.
Y. Bousquet, X. Carbonneau, I. Trébinjac, D. Dufour and M. Roumeas, Description of the unsteady flow pattern from peak efficiency to near surge in a subsonic centrifugal compressor stage, Proceedings of the 10th European Conference on Turbomachinery: Fluid Dynamics and Thermodynamics, Lappeenranta, Finland, April (2013) 15–19.
J. Tang, T. Turunen-Saaresti, A. Reunanen, J. Honkatukia and J. Larjola, Numerical investigation of the effect of tip clearance to the performance of a small centrifugal compressor, Proceedings of ASME Turbo Expo, Barcelona, Spain, May 8-11 (2006) paper no. GT2006-90893.
A. Jaatinen, A. Grönman, T. Turunen-Saaresti and P. Röyttä, Effect of vaneless diffuser width on the overall performance of a centrifugal compressor, Proceedings of the Institution of Mechanical Engineers, Part A: J. of Power and Energy, 225 (2011) 665–673.
A. Jaatinen, T. Turunen-Saaresti, A. Grönman, P. Röyttä and J. Backman, Experimental study of the effect of the tip clearance to the diffuser flow field and stage performance of a centrifugal compressor, Proceedings of ASME Turbo Expo, Copenhagen, Denmark, June 11-15 (2012) paper no. GT2012-68445.
A. Jaatinen-Värri, P. Röyttä, T. Turunen-Saaresti and A. Grönman, Experimental study of centrifugal compressor vaneless diffuser width, J. of Mechanical Science and Technology, 27 (2013) 1011–1020.
A. Jaatinen-Värri, T. Turunen-Saaresti, R. Röyttä, A. Grönman and J. Backman, Experimental study of centrifugal compressor tip clearance and vaneless diffuser flow fields, Proceedings of the Institution of Mechanical Engineers, Part A: J. of Power and Energy, 227 (2013) 885–895.
A. Jaatinen-Värri, T. Turunen-Saaresti, A. Grönman, J. Backman and J. Tiainen, Numerical investigation of centrifugal compressor tip clearance, Proceedings of ASME Turbo Expo, Montreal Canada, June 15-19 (2015) paper no. GT2015-43199.
J. Oh and G. L. Agrawal, Numerical investigation of low solidity vaned diffuser performance in a high-pressure centrifugal compressor, Part I: Influence of Vane Solidity, Proceedings of ASME Turbo Expo, May 14-17, Montreal, Canada (2007) paper no. GT2007-27260.
J. Oh, C. W. Buckley and G. L. Agrawal, Numerical investigation of low solidity vaned diffuser performance in a highpressure centrifugal compressor, Part II: Influence of vane stagger, Proceedings of ASME Turbo Expo, June 9-13, Berlin, Germany (2008) paper no. GT2008-50178.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Weon Gyu Shin
Ahti Jaatinen-Värri is an Associate Professor at the Laboratory of Fluid Dynamics, in Lappeenranta University of Technology, Finland. His main areas of interest are internal flows in various high-speed turbomachinery, especially centrifugal compressor aerodynamics.
Rights and permissions
About this article
Cite this article
Jaatinen-Värri, A., Tiainen, J., Turunen-Saaresti, T. et al. Centrifugal compressor tip clearance and impeller flow. J Mech Sci Technol 30, 5029–5040 (2016). https://doi.org/10.1007/s12206-016-1022-8
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-016-1022-8