Abstract
Experimental and theoretical research on the rotational behavior of Multi-cell shaped concrete-filled steel tubular (MCFST) connection under low-period cyclic load is performed. The experimental results showed that the design parameters had significant effects on the elastic rotational stiffness of the connection, and affected the sequence and position of the plastic hinges appearance at the column and beam ends. Furthermore, the damage mechanism of the plastic hinge lines is obtained, and the simultaneous yielding for the plastic hinges results in the rapid increase of the beam end rotation. In order to handle the problem with irregular geometry boundary and uneven distribution of tightening-ring stresses a differential element of an unified material is proposed considering the effective tightening-ring stresses of special-shaped steel tube on confined concrete, which can be used to analyse the whole mechanical and damage performance of the connection. Combining unified design theory and experimental results, the calculation for the elastic bending rigidity of the connection is obtained. Finally, the moment-rotation relation model of the connection is proposed by regression analysis on experimental results, and the theoretical results are observed to agree well with the experimental results.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Abbreviations
- A c, A s (mm2):
-
Sectional areas of confined concrete and steel tube
- A c1, A c2 (mm2):
-
Total areas of confined concrete in effective constraint region of limbs parallel and vertical to beams
- a f(mm):
-
Length of confined concrete of limbs vertical to beam in web direction
- As1, A s2 (mm2):
-
Total areas of limbs parallel and vertical to beams in model of equivalent concrete-filled circular steel tube
- a wn1, a fn1 (mm):
-
Lengths of steel webs of limbs parallel and vertical to beams on left side of neutral axis u
- a wn2, a fn2 (mm):
-
Length of steel webs of limbs parallel and vertical to beams on right side of neutral axis u
- b w, b f (mm):
-
Vertical lengths of confined concrete of limbs parallel and vertical to beams
- D, F :
-
Calculation parameters for elastic modulus of unified material composed of special-shaped steel tubulars and confined concrete in compressive region
- dϕ :
-
Differential element in model of equivalent concrete-filled circular steel tubular
- E c, E s (MPa):
-
Elastic moduli of confined concrete and steel tube
- E ′s , E ″s (MPa):
-
Second and third modulus of steel material
- E sc (MPa):
-
Elastic modulus of unified material composed of special-shaped steel tubulars and confined concrete in compressive region
- E scm (MPa):
-
Elastic moment resisting modulus of joint at event I
- E scm I sc0 :
-
Composite bending rigidity of joint at state I
- f(β):
-
Influence coefficient of height to thickness ratio of column section on elastic bending rigidity of joint
- H (mm):
-
Height of column
- H b (mm):
-
Height of beam cross section
- H f (mm):
-
Width of steel tube of limbs vertical to beam
- H w1, H w2 (mm):
-
Widths of flange 1 and 2
- I c (mm4):
-
Moment of inertia of confined concrete
- I s (mm4):
-
Moment of inertia of special shaped steel tube
- I sc (mm4):
-
Modified composite moment of inertia for joint
- I sc0 (mm4):
-
Composite moment of inertia for joint
- k :
-
Influence parameters of cross-section shape and height to thickness ratio of column section on shape characteristic of Mj-θr curves
- K e (kN·m):
-
Elastic bending rigidity of joint
- L w, L f (mm):
-
Depths of steel tube of limbs parallel and vertical to beams
- M e, M y (kN·m):
-
Bending moments at state points I and II
- M j (kN·m):
-
Bending moment of panel zone
- M uj (kN·m):
-
Ultimate bending moment of joint
- N (kN):
-
Axial pressure force on top of column
- N (kN):
-
Load applied to column
- n :
-
Axial compression ratio of column
- n s :
-
Parameter related to shape of Mj-θr curves
- p (N/mm2):
-
Constraint reaction stresses on steel tubes of limbs parallel and vertical to beams
- p cw, p cf (N/mm2):
-
Tightening-ring stresses of confined concrete in effective constraint region of limbs parallel and vertical to beams
- p e (N/mm2):
-
Equivalent tightening-ring stresses of confined concrete in model of equivalent concrete-filled circular steel tube
- p ecw, p ecf (N/mm2):
-
Equivalent tightening-ring stresses of confined concrete in effective constraint regions of limbs parallel and vertical to beams in model of equivalent concrete-filled circular steel tubular
- p hf, p vf (N/mm2):
-
Horizontal and vertical constraint reaction stresses on steel tubes exerted by confined concrete in limbs vertical to beam
- p hw, p vw (N/mm2):
-
Horizontal and vertical constraint reaction stresses on steel tube exerted by confined concrete in limb parallel to beam
- Q (kN):
-
Intersection point between starting point of para-curve corresponding to web limb and y-axis
- S (mm2):
-
Ineffective restraint area of confined concrete
- t b, t d (mm):
-
Thicknesses of flanges of beam and internal diaphragm
- t f1, t f2 (mm):
-
Thicknesses of flanges of limbs parallel and vertical to beams
- t w1, t w2 (mm):
-
Thicknesses of steel webs of limbs parallel and vertical to beams
- u :
-
Neutral axis of column section
- V (kN):
-
Lateral load on top of column
- α 1 :
-
Ratio of steel content of limb parallel to beam
- α 2 :
-
Ratio of steel content of limbs vertical to beam
- α E :
-
Ratio of modulus elastic of steel tube to that of confined concrete
- α s1, α s2 :
-
Stiffness reduction ratios at yield point and plastic stiffness reduction point
- β :
-
Height to thickness ratio of column section
- γ :
-
Ratio of moment of inertia of steel tube to that of confined concrete
- δ :
-
Relative angle between plastic hinges at beam and column ends
- δ m (mm):
-
Horizontal displacement of panel zone
- δ u (mm):
-
Horizontal displacement of column
- θ b :
-
Rotation of beam end
- θ c :
-
Rotation of column end
- θ e, θ y, θ r :
-
Rotations at state points I, II and III
- θ e :
-
Reference rotation which is ratio of ultimate bending moment ofjoint to elastic bending rigidity of joint
- θ r :
-
Relative rotation between ends of column and beam
- λ :
-
Ratio of sectional area of steel tube to that of confined concrete
- ξ :
-
Confinement coefficient of whole unified material constituted by limbs parallel and vertical to beams
- ξ f :
-
Confinement coefficient ξf of limbs vertical to beam
- ξ w :
-
Confinement coefficient of limb parallel to beam
- σ cB (N/mm2):
-
Axial compressive strength of confined concrete
- σ sw, σ sf (N/mm2):
-
Transverse tension stresses of steel webs of limbs parallel and vertical to beams
- σ sy, σ sr, σ sB (N/mm2):
-
Stress at yield point, plastic stiffness reduction point, and ultimate point
- φ :
-
Initial angle of para-curve at intersection point
References
Abbas H, Siddiqui NA, Khateeb BM, Almusallam TH, Al-Salloum YA (2021) Performance of new CFST square column-to-foundation connections for cyclic loads. Journal of Constructional Steel Research 185:106868, DOI: https://doi.org/10.1016/j.jcsr.2021.106868
Cao JJ, Packer JA, Yang GJ (1998) Yield line analysis of RHS connections with axial loads. Journal of Constructional Steel Research 48:1–25, DOI: https://doi.org/10.1016/S0143-974X(98)90143-2
CECS159:2004 (2004) Technical specification for structures with concrete-filled rectangular steel tube members. China Architecture & Building Press, Beijing, China, 27–38 (in Chinese)
Chen X, Xue JY, Li HC, Lu X, Tu GX (2023) Elastoplastic analysis of shear resistance of special-shaped concrete-filled steel tubular connection. Journal of Constructional Steel Research 201:107712, DOI: https://doi.org/10.1016/j.jcsr.2022.107712
Cheng Y, Yang YL, Liu JP, Nie WQ, Chen YF (2023) Seismic performance and design method of T-shaped CFST column to U-shaped steel-concrete composite beam joint with vertical stiffeners. Engineering Structures 275:115270, DOI: https://doi.org/10.1016/J.engstruct.2022.115270
GB/T 228.1-2010 (2010) Metallic materials-tensile testing - part 1: method of test at room temperature. China Architecture & Building Press, Beijing, China, 1–19 (in Chinese)
GB/T 50081-2002 (2002) Standard for test method of mechanical properties on ordinary concrete. China Architecture & Building Press, Beijing, China, 4–15 (in Chinese)
Han LH, T Z, W WD (2009) Experiment, theory and methodology of modern composite and hybrid structures. Science Publishing Press, Beijing, China, 239–246 (in Chinese)
Khndada AE, Geschwindner LF (1997) Nonlinear dynamic analysis of steel frames by modal superposition. Engineering Structures 123(11): 1519–1527, DOI: https://doi.org/10.1061/(ASCE)0733-9445(1997)123:11(1519)
Liu WH, Guo’ YL, Tian ZH, Yang X, Li JY (2023) Experimental and numerical study of T-shaped irregularly concrete-filled steel tube columns under combined axial loads and moments. Journal of Building Engineering 65:105796, DOI: https://doi.org/10.1016/j.jobe.2022.105796
Liu XG, Liu JP, Yang YL, Cheng GZ, Joel Lanning J (2020) Resistance of special-shaped concrete-filled steel tube columns under compression and bending. Journal of Constructional Steel Research 169:106038, DOI: https://doi.org/10.1016/j.jcsr.2020.106038
Liu J, Zhou T, Lei ZY, Chen XD, Chen ZH (2019) Eccentric compression performance of slender L-shaped column composed of concrete-filled steel tubes connected by steel linking plates. Journal of Constructional Steel Research 162:1–16, DOI: https://doi.org/10.1016/j.jcsr.2019.06.012
Mander JB, Priestley MJN, Park R (1988) Theoretical stress-strain model for confined concrete, Journal of Structural Engineering 114(8): 1804–1826, DOI: https://doi.org/10.1061/(asce)0733-9445(1988)114:8(1804)
Patel KV, Chen WF (1984) Nonlinear analysis of steel moment connections. Journal of Structural Engineering 110(8):1861–1874, DOI: https://doi.org/10.1061/(ASCE)0733-9445(1984)110:8(1861)
Qin Y, Chen ZH, Rong B (2015a) Component-based mechanical models for concrete-filled RHS connections with diaphragms under bending moment. Advances in Structural Engineering 18(8):1241–1255, DOI: https://doi.org/10.1260/1369-4332.18.8.1241
Qin Y, Chen ZH, Rong B (2015b) Modeling of CFRT through-diaphragm connections with H-beams subjected to axial load. Journal of Constructional Steel Research 114:146–156, DOI: https://doi.org/10.1016/j.jcsr.2015.04.015
Qin Y, Chen ZH, Wang XD (2014) Elastoplastic behavior of through-diaphragm connections to concrete-filled rectangular steel tubular columns. Journal of Constructional Steel Research 93:88–96, DOI: https://doi.org/10.1016/j.jcsr.2013.10.011
Shehab BA, Ekmekyapar T (2021) Joints behaviour of through steel beam to composite column connection: Experimental study. Marine Structures 76:1–23, DOI: https://doi.org/10.1016/j.marstruc.2020.102921
Wang WD, Han LH, Uy B (2008) Experimental behaviour of steel reduced beam section to concrete-filled circular hollow section column connections. Journal of Constructional Steel Research 64:493–504, DOI: https://doi.org/10.1016/j.jcsr.2007.10.005
Yang YL, Wang YY, Fu F, Liu JC (2015) Static behavior of T-shaped concrete-filled steel tubular columns subjected to concentric and eccentric compressive loads. Thin-Walled Structures 95:374–388, DOI: https://doi.org/10.1016/j.tws.2015.07.009
Yang YL, Wang GJ, Yang WQ, Wei X, Chen YF (2022) Experimental research on fire behavior of L-shaped CFST columns under axial compression. Journal of Constructional Steel Research 198:107505, DOI: https://doi.org/10.1016/j.jcsr.2022.107505
Zhang YB, Han LH, Zhou K, Yang ST (2019) Mchanical performance of hexagonal multi-cell concrete-filled steel tubular (CFST) stub columns under axial compression. Thin-Walled Structures 134:71–83, DOI: https://doi.org/10.1016/j.tws.2018.09.027
Zheng YQ, Pengsong Lai PS (2020) Experimental behavior of T-shaped concrete-filled steel tubular columns under diagonal cyclic loading. Journal of Constructional Steel Research 169:106037, DOI: https://doi.org/10.1016/j.jcsr.2020.106037
Zhong ST (2003) The concrete-filled steel tubular structures. Tsinghua University Press, Beijing, China, 61–83 (in Chinese)
Zhong ST (2006) The research and application of united design theory of concrete filled steel tube. Tsinghua University Press, Beijing, China, 37–77 (in Chinese)
Zhou GJ, An YH, Li DS, Ou JP (2019) Analytical model of moment-rotation relation for steel beam to CFST column connections with bidirectional bolts. Engineering Structures 196:1–11, DOI: https://doi.org/10.1016/j.engstruct.2019.109374
Acknowledgments
This work is supported by the National Natural Science Foundation of China (Grant No.: 51808195), and the National Natural Science Foundation of China (Grant No.: 50978217). The financial support is highly appreciated.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Chen, X., Xue, J., Li, H. et al. Performance-based Analysis of Elastoplastic Rotational Behavior of Multi-cell Shaped Concrete-filled Steel Tubular Connection. KSCE J Civ Eng 27, 4300–4322 (2023). https://doi.org/10.1007/s12205-023-0390-8
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-023-0390-8