Abstract
At present, about 40% of the fuel energy is discharged into air with the exhaust gas when an automobile is working, which is a big waste of energy. A thermoelectric generator (TEG) has the ability to harvest the waste heat energy in the exhaust gas. The traditional TEG cold-end is cooled by the engine cooling system, and although its structure is compact, the TEG weight and the space occupied are important factors restricting its application. In this paper, under the premise of ensuring the TEG maximum net output power and reducing the TEG water consumption as much as possible, the optimization of the TEG water thickness in the normal direction of the cold-end surface (WTNCS) is studied, which results in lighter weight, less space occupied and better automobile fuel economy. First, the thermal characteristics of the target diesel vehicle exhaust gas are evaluated based on the experimental data. Then, according to the thermoelectric generation model and the cold-end heat transfer model, the effect of the WTNCS on the cold-end temperature control stability and the system flow resistance are studied. The results show that the WTNCS influences the TEG cold-end temperature. When the engine works in a stable condition, the cold-end temperature decreases with the decrease of the WTNCS. The optimal value of the WTNCS is 0.02 m and the TEG water consumption is 8.8 L. Comparin it with the traditional vehicle exhaust TEG structure, the power generation increased slightly, but the water consumption decreased by about 39.5%, which can save fuel at0.18 L/h when the vehicle works at the speed of 60 km/h.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Abbreviations
- Q :
-
Heat transfer rate (kW)
- h :
-
Enthalpy (kJ/kg)
- D :
-
Equivalent tube outer diameter (m)
- H :
-
Convective heat transfer rate (W/m2 K)
- λ :
-
Thermal conductivity (W/m K)
- μ :
-
Viscosity (kg/ms)
- Pr :
-
Prandtl number
- T :
-
Temperature (K)
- G :
-
Mass flux (kg/m2s)
- ρ :
-
Density (kg/m3)
- d :
-
Equivalent tube inner diameter
- L :
-
Equivalent tube length (m)
- Re :
-
Reynolds number
- Nu :
-
Nusselt number
- S :
-
Nucleate boiling correction factor
- E :
-
Film boiling correction factor
- M :
-
Molar mass (kg/k mol)
- f :
-
Mass fraction
- m :
-
Mass flow rate (kg/s)
- γ :
-
Equivalent tube thickness (m)
- exh:
-
Exhaust
- g :
-
Gas state
- tp :
-
Two-phase state
- a, x, b :
-
State point for exhaust gas
- water:
-
Water
- nb :
-
Nucleate boiling
- ph :
-
Preheated state
- 2, 3, 4 :
-
State point for cooling water
References
Y.D. Deng, W. Fan, K. Ling, and C.Q. Su, J. Electron. Mater. 41, 1698 (2012). doi:10.1007/s11664-012-2068-8.
Y.D. Deng, X. Liu, S. Chen, and N.Q. Tong, J. Electron. Mater. 42, 1634 (2013). doi:10.1007/s11664-012-2359-0.
M. Bai, G. Tan, Y. Deng, W. Wang, and H. Yan, Cold-end Temperature Control Method for the Engine Exhaust Heat Thermoelectric Module (No. 2014-01-2343). SAE Technical Paper (2014). doi:10.4271/2014-01-2343.
J.G. Haidar and J.I. Ghojel, Proceedings ICT 2001, XX International Conference on Thermoelectrics (IEEE, 2001). doi:10.1109/ICT.2001.979919.
Y.Y. Hsiao, W.C. Chang, and S.L. Chen, Energy 35, 1447 (2010).
C. Yu and K.T. Chau, Energy Convers. Manag. 50, 1506 (2009).
X.L. Gou, H. Xiao, and S.W. Yang, Appl. Energy 87, 3131–3136 (2010).
W. He, Y. Su, S. Riffat, J. Hou, and J. Ji, Appl. Energy 88, 5083–5089 (2011).
K. Ikoma, M. Munekiyo, K. Furuya, M. Kobayashi, T. Izumi, and K. Shinohara, Proceedings ICT 1998, XVII International Conference on Thermoelectrics (IEEE, 1998), pp. 464–467.
C.T. Hsu, D.J. Yao, K.J. Ye, and B. Yu, J. Renew. Sustain. Energy 2, 389 (2010).
Y.D. Deng, X. Liu, S. Chen, H.B. Xing, and C.Q. Su, J. Electron. Mater. 43, 1815 (2014). doi:10.1007/s11664-013-2881-8.
H.G. Zhang, E.H. Wang, and B.Y. Fan, Energy Convers. Manag. 65, 438 (2013).
W.Z. Gu, J.R.S. Shen, C.F. Ma, and Y.M. Zhang, Enhanced Heat Transfer (Beijing: Science Press, 1990), p. 410.
J.P. Holman, Heat Transfer, 9th ed. (New York: McGraw-Hill, 2002), p. 282.
X. Wang, H. Wang, and H. Wang, J. Wuhan Univ. Technol. 33, 67 (2011).
S.M. Ghiaasiaan, Two-Phase Flow, Boiling, and Condensation. Conventional and Miniature Systems (New York: Cambridge University Press, 2008), p. 303.
REFPROP version 9.0, NIST standard reference database 23. The US Secretary of Commerce, America (2007).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhou, L., Guo, X., Tan, G. et al. Study on the Influence of the Cold-End Cooling Water Thickness on the Generative Performance of TEG. J. Electron. Mater. 46, 2576–2586 (2017). https://doi.org/10.1007/s11664-016-5057-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11664-016-5057-5