Abstract
The mechanical properties of dual-phase steel (DP1000) over the strain rate range of 10−3-103 s−1 were studied using an electronic universal testing machine and a high-speed tensile testing machine. The plastic deformation mechanism was investigated from the perspectives of the strain rate sensitivity index, activation volume and dynamic factors. The results show that the tensile strength and yield strength of DP1000 increase as the strain rate increases. The elongation increases without any change after fracture, and then decreased rapidly when the strain rate reaches 103 s−1. The true strain curves of DP1000 show three stages: the point of instability decreases in the strain range of 10−3-10−1 s−1; the instability point increases between 100-5×102 s−1; above 5×102 s−1, and the instability strain becomes smaller again. The plastic deformation mechanism of the DP was determined by the competitive contributions of work hardening (strain hardening, strain rate hardening) and softening effects due to the adiabatic temperature rise.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Mozumder YH, Babu KA, Saha R, et al. Flow Characteristics and Hot Workability Studies of a Ni-containing Fe-Mn-Al-C Lightweight Duplex Steel[J]. Mater. Charact., 2018, 146: 1–14
Lei Y, Huang SY, Meng ZH, et al. Effects of Biaxial Tensile on the Deformation Behavior of DP590 High-strength Steel Sheet under High Strain Rate[J]. J. Wuhan Univ. Technol. -Mater. Sci. Ed., 2017, 32: 1 441–1 445
Depover T, Vercruysse F, Elmahdy A, et al. Evaluation of The Hydrogen Embrittlement Susceptibility in DP Steel Under Static and Dynamic Tensile Conditions[J]. Int. J. Eng. Sci. 2019, 123: 118–125
Nakada N, Tsukahara M, Fukazawa K, et al. Very Fine Structured DP steel with Tempered-martensite Matrix Fabricated by Fast Heating[J]. Mater. Trans. 2018, 59: 166–171
Zamani M, Mirzadeh H, Maleki M, et al. Enhancement of Mechanical Properties of Low Carbon Dual Phase Steel Via Natural Aging[J]. Mater. Sci. Eng. A, 2018, 734: 178–183
Sha Q, Li D, Li G, et al. Dynamic and Static Recrystallization Behaviour of Coarse-Grained Austenite in a Nb-V-Ti Microalloyed Steel[J]. J. Iron Steel Res. Int. 2014, 21: 233–239
Fu Y, Yu H. Application of Mathematical Modeling in Two-Stage Rolling of Hot Rolled Wire Rods[J]. J. Mater. Process. Tech. 2014, 214: 1 962–1 970
Dai QF, Song RB, Guo Z. Research on Continuous Annealing Process of 1 000 MPa Cold-rolled Dual Phase Steel Using Orthogonal Design Method[J]. Met. Sci. Heat Treat. 2013, 55: 1–2
Pang QH, Tang D, Zhao ZZ. Microstructure-based Model for the Stress—Strain Relationship of Hot-Rolled Dual-Phase Steel[J]. J. Univ. Sci. Technol. B, 2015, 37: 1 442–1 446
Beynon ND, Jones TB, Fourlaris G. Effect of High Strain Rate Deformation On Microstructure of Strip Steels Tested Under Dynamic Tensile Conditions[J]. Metal Sci. J. 2013, 21:103–112
Slycken JV, Bouquerel J, Verleysen P, et al. Static and Impact-dynamic Characterization and Modeling of Multiphase TRIP Steels[J]. Mater. Sci. Forum, 2009, 638: 3 585–3 590
Beukel AVD. Theory of the Effect of Dynamic Strain Aging on Mechanical Properties[J]. Phys. Status. Solidi. A, 2010, 30: 197–206
Beukel AVD, Kocks UF. The Strain Dependence of Static and Dynamic Strain-aging[J]. Acta. Metall. 1982, 30: 1 027–1 034
Wei W, Feng Y, Han L, et al. High-Temperature Low-Cycle Fatigue Behavior of HS80H Ferritic-Martensitic Steel Under Dynamic Strain Aging[J]. J. Mater. Eng. Perform. 2018, 27(7): 6 629–6 635
Kang J, Wang C, Li YJ, et al. Effect of Direct Quenching and Partitioning Treatment on Mechanical Properties of a Hot Rolled Strip Steel[J]. J. Wuhan Univ. Technol. Mater. Sci. Ed.), 2016, 31: 178–185
Li Z. Controlled rolling and cooling process for low carbon cold forging steel[J]. J. Wuhan Univ. Technol. Mater. Sci. Ed.), 2010, 25: 89–93
Tugluca IB, Koyama M, Shimomura Y, et al. Lowering Strain Rate Simultaneously Enhances Carbon- and Hydrogen-Induced Mechanical Degradation in an Fe-33Mn-1.1C Steel[J]. Metall. Mater. Trans. A, 2019, 50: 1 137–1 141
Matsuno T, Teodosiu C, Maeda D, et al. Mesoscale Simulation of the Early Evolution of Ductile Fracture in Dual-phase Steels[J]. Int. J. Plasticity. 2015, 74: 17–34
Kapoor R, Nemat-Nasser S. Comparison Between High and Low Strain-rate Deformation of Tantalum[J]. Metall. Mater. Trans. A, 2000, 31: 815–823
Johnston WG, Gilman JJ. Dislocation Velocities, Dislocation Densities, and Plastic Flow in Lithium Fluoride Crystals[J]. J. Appl. Phys. 1959, 30: 129–144
Azuma M, Goutianos S, Hansen N, et al. Effect of Hardness of Martensite and Ferrite on Void Formation in Dual Phase Steel[J]. Mater. Sci. Tech. 2012, 28: 1 092–1 100
Han HQ, Huo G, Li UY, et al. Microstructure and Property of Cold Rolled and Heat Treated DP Steel Microalloyed With Titanium[J], J. Iron Steel Res. 2009, 21: 28–42
Liang W, Murakawa H, Deng D. Investigation of Welding Residual Stress Distribution in a Thick-Plate Joint with an Emphasis on the Features Near Weld End-start[J]. Mater. Design, 2015, 67: 303–312
J Si, Z Jia, Wang J, et al. Comparative Analysis of Cold-mixed Epoxy and Epoxy SBS-modified Asphalts: Curing Rheology, Thermal, and Mechanical Properties[J]. Constr. Build Mater. 2018, 176: 165–171
Peng J, Li KS, Pei JF, et al. Temperature-dependent SRS Behavior of 316L and its Constitutive Model[J]. Acta Metall. Sin. 2018, 31: 234–244
Tanga M, Kubinb L P, Canovac G R. Dislocation Mobility and the Mechanical Response of BCC Single Crystals: a Mesoscopic Approach[J]. Acta Mater. 1998, 46: 3 221–3 235
Levi-Hevroni D, Kochavi E, Kofman B, et al. Experimental and Numerical Investigation on the Dynamic Increase Factor of Tensile Strength in Concrete[J]. Int. J. Impact Eng. 2018, 114: 93–104
Author information
Authors and Affiliations
Corresponding authors
Additional information
Funded by the National Natural Science Foundation of China (No. 52004122), the State Key Laboratory of Marine Equipment made of Metal Material and Application(No.SKLMEA-USTL-201906), the Guidance plan of Natural Science Foundation of Liaoning Province (No.2019-ZD-0025), and the Key Project of Liaoning Education Department (No. 2019FWDF03)
Rights and permissions
About this article
Cite this article
Pang, Q., Zhao, Z., Xu, M. et al. Plastic Deformation Mechanism of Dual-phase Steel at Different Strain Rates. J. Wuhan Univ. Technol.-Mat. Sci. Edit. 35, 1142–1148 (2020). https://doi.org/10.1007/s11595-020-2366-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11595-020-2366-6