Abstract
Three types of near-net shape casting aluminum parts were investigated by computed tomography to determine casting defects and evaluate quality. The first, second, and third parts were produced by low-pressure die casting (Al-12Si-0.8Cu-0.5Fe-0.9Mg-0.7Ni-0.2Zn alloy), die casting (A356, Al-7Si-0.3Mg), and semi-solid casting (A356, Al-7Si-0.3Mg), respectively. Unlike die casting (second part), low-pressure die casting (first part) significantly reduced the formation of casting defects (i.e., porosity) due to its smooth filling and solidification under pressure. No significant casting defect was observed in the third part, and this absence of defects indicates that semi-solid casting could produce high-quality near-net shape casting aluminum parts. Moreover, casting defects were mostly distributed along the eutectic grain boundaries. This finding reveals that refinement of eutectic grains is necessary to optimize the distribution of casting defects and reduce their size. This investigation demonstrated that computed tomography is an efficient method to determine casting defects in near-net shape casting aluminum parts.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Guo S J, Xu Y, Han Y, et al. Near net shape casting process for producing high strength 6xxx aluminum alloy automobile suspension parts. Transactions of Nonferrous Metals Society of China, 2014, 24(7): 2393–2400
Kamat G R. Low pressure counter gravity casting of aluminium alloys. Transactions of the Indian Institute of Metals (India), 1992, 45(3): 177–180
Chandley G D. Counter gravity casting of aluminum in investment and sand molds. American Foundrymen’s Society, 1986, 94: 209–214
Jie W Q, Li X L, Hao Q T. Counter-gravity casting equipment and technologies for thin-walled Al-alloy parts in resin sand molds. Materials Science Forum, 2009, 618–619: 585–589
Chandley G D. Use of vacuum for counter-gravity casting of metals. Materials Research Innovations, 1999, 3(1): 14–23
Rosc J, Pabel T, Geier G F, et al. Method for the estimation of porosity analysis of CT-data. Giesserei-rundschau, 2010, 57: 244–246
Mayo S C, Stevenson A W, Wilkins S W. In-line phase-contrast X-ray imaging and tomography for materials science. Materials (Basel), 2012, 5(12): 937–965
Withers P J. Fracture mechanics by three-dimensional crack-tip synchrotron X-ray microscopy. Philosophical Transactions of the Royal Society A, 2015, 373(2036): 20130157
Samavedam S, Sakri S B, Hanumantha Rao D, et al. Estimation of porosity and shrinkage in a cast eutectic Al-Si alloy. Canadian Metallurgical Quarterly, 2014, 53(1): 55–64
Nicoletto G, Konecná R, Fintova S. Characterization of microshrinkage casting defects of Al-Si alloys by X-ray computed tomography and metallography. International Journal of Fatigue, 2012, 41: 39–46
Cabeza S, Mishurova T, Garcés G, et al. Stress-induced damage evolution in cast AlSi12CuMgNi alloy with one-and two-ceramic reinforcements. Journal of Materials Science, 2017, 52(17): 10198–10216
Acknowledgements
Jiehua Li acknowledges the financial support provided by the Major International (Regional) Joint Research Project (Grant No. 51420105005) and Overseas, Hong Kong, Macao Scholars Cooperative Research Fund (Grant No. 51728101) from China.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, J., Oberdorfer, B., Habe, D. et al. Determining casting defects in near-net shape casting aluminum parts by computed tomography. Front. Mech. Eng. 13, 48–52 (2018). https://doi.org/10.1007/s11465-018-0493-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11465-018-0493-y