Abstract
Surface water and groundwater are significant for population and other activities due to the decreasing surface water flow toward Iraq. Therefore, there is a need to analyze groundwater’s quality and classification and its applicability as an alternative in various human activities in the study area. This study utilized the groundwater quality index model for drinking uses (GW.Q.I.) and entered the resulting values in the GIS environment. This model was applied to 56 wells in Al-Hillah city by measuring twelve variables in each well. The measured variables were calcium (Ca), magnesium (Mg), sodium (Na), chloride (Cl), sulfate (SO4), bicarbonate (HCO3), total hardness (TH), total dissolved solids (TDS), nitrate (NO3), and electric conductivity (EC). The prediction map of GW.Q.I. was produced in the GIS. Then, the distributing map was divided into six categories based on the suitability of groundwater for drinking uses. The areas’ values of six categories with their ratings were about 5 km2 (excellent), 122 km2 (good), 610 km2 (poor), 63 km2 (very poor), 36 km2 (contaminated), and 24 km2 (very contaminated). For the entire study area, the average value of the GW.Q.I. was 177, classified as poor for drinking uses.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
1 Introduction
Many factors affect the water quality index (W.Q.I.), including population growth rate, climate change, and expanded industrial and agriculture activities, which caused a significant decrease in quality of water, which represented a local and global challenge (Krishan et al., 2016). Various physical and chemical variables were adopted by researchers to evaluate the W.Q.I. for drinking uses. Walsh and Wheeler, (2012) illustrated that multiple factors should be considered when analyzing the water body’s quality. The physicochemical variables relate to the level of abundance of water. Also, the concentrations of variables in the water body significantly affect evaluating the W.Q.I. Furthermore, studying these variables one-variable-at-a-time does not show a comprehensive vision for the W.Q.I. Moreover, water treatment is required if the variables do not meet the region’s standards (Bouderbala, 2017).
Numerical or mathematical methods can calculate the W.Q.I. for drinking uses. These methods can give a broad view of the groundwater quality in a specific area timelessly and effortlessly and, therefore, avoid wells in areas where groundwater is unsuitable to use (Alobaidy et al., 2010). Water source characteristics directly affect groundwater quality and its utilization suitability. Continuous monitoring of the chemical and physical parameters should be maintained and controlled to keep the groundwater quality in a good state to be used.
Recently, the water shortage crisis started to arise in Iraq due to climate change, construction of dams upriver, wars, and unsystematic drinking water use. This shortage raised the need to invest in groundwater resources. Thus, quality analysis is required to check its suitability for use. GIS is highly capable of creating wells’ distribution maps using relevant variables. These maps help specialists cross-examine water quality across multiple sites (Chabuk et al., 2020).
The groundwater quality index method is the most widespread method for assessing water quality in developing countries to maintain water quality. It represents an essential storage strategy for countries’ future uses when decreasing the surface water level. It is a permanent source for groundwater research as it is one of Iraq’s most critical natural resources. The suitability of groundwater in the city of Hillah for the different uses was studied for construction purposes mainly. The groundwater level fluctuations as well as its chemical composition at Hilla city was carefully considered. Two negative influences have a combined effect on concept tolerance. All tested samples for the groundwater showed that they are not suitable for domestic, animal as well as some industrial purposes.
Chabuk et al., (2020) evaluated the groundwater for irrigation in Al-Hillah city by applying the water quality index for the irrigation model (WQIIR) in the GIS environment. They measured Ca, Mg, Cl, EC, HCO3, Na, and SAR in 48 wells distributed in different areas in Al-Hillah city. The results based on the predicted maps in 2016
showed that the values of areas in 2016 were about 48.4 km2, 399 km2, 384.3 km2, 28.1 km2, and 0.2 km2. These categories were classified for irrigation (respectively) as a severe restriction, high restriction, moderate restriction, low restriction, and no restriction.
The W.Q.I. method was applied to evaluate the groundwater quality by many researchers in various study areas. Alikhan et al., (2020) estimated the groundwater quality at five wells in Al Najaf city, Iraq, in 2017 using nine parameters (pH, EC, TDS, Ca, Mg, Cl, Na, K, and SO4). The study found that the total value of the W.Q.I. was classed under a poor rating.
Mohammed et al., (2020) adopted the W.Q.I. method to evaluate groundwater quality in the Domiz refugee camp, Duhok governorate. Twenty-four variables were measured in 8 wells. The results showed that the W.Q.I. values were rated as very poor in well 1; poor in wells 2 and 3; good in wells 4, 6, and 7; and excellent in wells 5 and 8.
Othman and Ibrahim, (2021) studied the quality of groundwater for drinking and other domestic uses and the activities of agriculture in Erbil city, Iraq, using the Canadian method for water quality index. They measured twenty-two variables in 16 wells in December/2016, and during the three months of March, June, and September/2017. These variables are pH, EC, TH, Ca, Mg, alkalinity, Cl, DO, BOD5, Na, K, SO4, PO4, NO3, oil and grease, Zn, Cu, Fe, Ni, Pb, Cd, and Hg. The results showed that the total value of W.Q.I. was 38.9, which classified the groundwater quality in the study area as poor quality.
The purpose of creating a new map of groundwater for drinking uses is that the study zone does not have a map for groundwater. The study zone has been affected by the global warming problem which led to searching for another way to cover the shortage. The map will be a document to help the researchers and the specialists. Also, the future plan for the Governorate is to secure additional drinking water sources when necessary and help with future suburbs of the city. Moreover, the map is an easy way to show the groundwater to users.
The research is interested in studying the suitability of the groundwater in Al-Hillah city for drinking and household uses by measuring the available variables within 56 wells from various areas. This study aims to create the prediction map using the groundwater quality index model for drinking uses (GW.Q.I.). Then, the values of GW.Q.I. will enter within the interpolation technique IDW in the GIS to produce the prediction map.
2 Methodology
2.1 Study Area
Al-Hillah city is situated between latitude 32° 29′ 00" N and longitude 44° 26′ 00". Al-Hillah city represents the capital of Babylon Governorate. Al-Hillah city includes three major cities: Al-Hillah center, Abi-Ghraq, and Al-Kifll (Fig. 1).
Al-Hillah city is situated in an arid region and its area of 860 km2. According to the Iraqi Ministry of Planning, (2017)Al-Hillah city has a population of nearly 993,000 inhabitants in 2020. The climate of Al-Hillah city is fluctuating seasonally and daily. The average speed of wind is 7.2 km/h year. The average annual rainfall in this area is about 100 mm, with an average annual relative humidity of 45%. The temperature is changing from more than 50 °C during the summer to over 0 °C during the winter (Iraqi Ministry of transportation constitutions, 2019).
The hydrogeology of Al-Hillah city, Babylon Governorate, is situated in the middle of Iraq in the aquifer of Mesopotamia zone (MZ) in a large flat plain (Al-Madhlom et al., 2020; Sissakian, 2013). The elevation of MZ ranges between 1 and 200 m above mean sea level (a.m.s.l.). The Mesopotamia region is covered mainly by the Quaternary sediments (Al-Madhlom et al., 2020). Al-Hillah city is positioned within the Mesopotamia plan silt zone covered by the Holocene Sequence with a thickness of about 20 m. Its primary compositions are silty clay, loamy sand, and sandy loam soil (Tyagi et al., 2013). The groundwater in the study area is shallow with ranges of 0.4–4.5 m (Chabuk et al., 2021) (Fig. 2) and flows with the trend of surface drainage from northwest to southeast (Al-Jiburi & Al-Basrawi, 2011).
The groundwater level rises during the winter and spring season due to increased rainfall and reduction in evaporation. The type of groundwater varies from sulfate to chloride based on the groundwater level and the quantity of recharge by runoff from discharge areas (Al-Jiburi & Al-Basrawi, 2011). In general, the groundwater, located near/around the surface water, has a good quality for use.
2.2 Prediction Maps in GIS Using the Interpolation Method (IDW)
To generate the interpolation map of the groundwater quality index for drinking uses for each variable, the interpolation inverse distance weighted technique (IDWT) was applied in the GIS. The interpolation method is used to estimate the unidentified point at a specific position based on the values of defined points near the unidentified points. The spatial interpolation technique is applied to produce interpolation maps of groundwater quality rather than other techniques (e.g., Kriging, Topo to Raster). The IDW technique gave better and more accurate results than other spatial ones, according to Abbas, (2013).
The IDWT is determined using Eq. (1) (Panhalkar & Jarag, 2016) as follows:
where SE0 is the estimated value of unidentified points; Ni is the value of the defined point; Di is the distance between SE0 and Ni; n is the number of Ni entered in the estimation process; ans p is the power value ≥ 1.
2.3 Method of Calculating Weights of Groundwater Quality Index for Drinking Uses
In this research, the weighted arithmetic method is employed to calculate the groundwater quality index for drinking uses. Twelve variables were used for the selected fifty-six wells within Al-Hillah city because the chosen variables are very significant to calculate the water quality index for different purposes. The groundwater quality index for drinking uses for selected wells in Al-Hillah city was calculated using the following Eqs. (2–4) (Tyagi et al., 2013):
where Su-Ii is the sub-index of the ith variable, IWi is the inverse weight of the standard value (STVi) of the ith variable, STVi is the standard value of the ith variable (WHO, 2017), Ci is the measured concentration value for the ith variable, Co is the ideal value for each variable in water that has zero value, excluding the pH value which is equal to 7.
For each well within Al-Hillah city, the water quality rating (GW.Q.R.) was given the deserve classification based on the category of the GW.Q.I. according to Alsaqqar et al., (2015) and Ali, (2017) (see Table 1).
The steps of calculating the GW.Q.I. for drinking uses for each variable can be seen in Table 2. The reading of the measured variables from sixty-five wells in Al-Hillah city in 2018 is shown in Table 3 (Iraqi Ministry of Water Resources, 2017).
3 Results and Discussion
This part is divided into three sections depending on the methodology approach. These sections evaluate the concentration values of variables measured in the selected wells, calculating the groundwater quality index for drinking uses for each well in the study area, and creating the maps of the GW.Q.I. and GW.Q.R. for the whole Al-Hillah city using the GIS.
3.1 Prediction Maps for Variables of Groundwater
In the current study, the prediction maps for twelve physicochemical variables measured from the network of wells distributed throughout Al-Hillah city were produced. Fifty-six wells were used to generate prediction maps using the interpolation method in the ArcGIS (10.5) software.
For the chosen variables of groundwater in the study area, the prediction maps for the sodium (Na), total dissolved solids (TDS), electrical conductivity (EC), chloride (Cl), bicarbonates (HCO3−1) sulfates (SO4), calcium (Ca), magnesium (Mg), nitrate (NO3), potassium (K), and pH can be seen in Figs. 3 and 4.
In Fig. 3a, b, c and d, the range values of Na, TDS, EC, and Cl that resulted from the interpolation maps using the IDW method in GIS were (respectively) 41–10,500 mg/l, 401–39,802 mg/l, 631–46,907 µmhos/cm, and 45–14,577 mg/l. For the variables of Na and Cl, category-1 with ranges of 41–2100 mg/l and 45–2900 mg/l covered the big area of the total study area of 93% and 96% respectively. The ranges of 400–8000 mg/l for TDS and 631–9500 for EC represented the most distribution values in the study area (see Fig. 3b and c).
The variable concentrations of HCO3 and SO4, distributed throughout the Al-Hillah city after interpolation within their maps ranged from 83 to 2019 mg/l, and from 66 to 11,531 mg/l, respectively, are shown in Fig. 3e and f. The range of 83–400 mg/l for HCO3 concentration was comprised 81% of the entire area, while 84% of the range of 66–2300 mg/l distributed throughout the prediction map of Al-Hillah city for SO4 concentration.
The readings of variable concentrations Ca, Mg NO3, and K were ranged between 24 and 3078 mg/l, 14 and 1801 mg/l, 0 and 209 mg/l, and 0 and 109 mg/l, respectively. These variables were distributed throughout the study area after interpolation for the readings of 56 wells. Figure 4a, b, c and d shows that the category-1 with ranges (mg/l) of 24–600, 14–360, 0–41.6, and 0–38.8 covered higher percentage of the study area 94% (Ca), 92% (Mg), 95% (NO3), and 97% (K). The range of the predicted map of pH that was divided into five categories was 6.3–8.7. The ranges of 7.26–7.74 and 7.74–8.22 represented together 95% of the total area (Fig. 4e).
The proportion areas of each category for the produced maps for eleven variables (Na, TDS, EC, Cl, HCO3, SO4, Ca, Mg, NO3, K, and pH) can be seen in Table 4.
3.2 Groundwater Quality Index for Drinking Uses (GW.Q.I.)
The groundwater quality index for drinking uses was calculated using the method of weighted arithmetic at the selected wells based on Eqs. (2, 3, 4). The GW.Q.I. values for the selected wells were calculated using the weighted arithmetic method (Table 1). All the parameters applied in this study are presented in Table 3 and were significant in this classification for the groundwater quality index. The GW.Q.I. values were classified based on the values of variables measured in the selected wells, as shown in Table 5. The sign of “ × ” referred to that put reading of variable in Table 5 over allowable standards limit, while the word “OK” meant this value of reading within the allowable limit. For instance, the groundwater quality index for drinking uses for well 5 was 82.3 and rated as good because the measured variables of HCO3, NO3, K, and pH were within the standards limit. These variables have significant effects on the value of the GW.Q.I. For well 2, all measured variables except NO3 and pH were over the standards limit; therefore, the value of the GW.Q.I. was 483.7 and rated as very contaminated for drinking uses. The value of the GW.Q.I. in well 48 was 32.1, and it was classified as excellent for drinking uses because all measured readings of variables were within the standards limit. Table 5 shows that most values of the TDS, EC, and Cl were higher than the allowable limit. These values indicated the groundwater in the study area was salinity. All readings of pH measured in the selected wells were the standard limit of 6.5–8.5.
Table 6 shows the values of the groundwater quality index for the variables of Na, TDS, EC, Cl, SO4, Ca, and Mg which were (respectively) 553.2, 1207.7, 867.6, 579.8, 692.9, 446.4, and 462.1 and they classified as very contaminated rating (Vc-GW). The variables HCO3 and K were rated as poor (P-GW) based on their values of groundwater quality index of 176.2 and 118.2, respectively, while NO3 and pH were rated as good (G-GW) and excellent (E) for drinking uses depending on the GW.Q.I. values of 99.4 and 17.8, respectively. The average value of the GW.Q.I. for the selected wells was 177, and the groundwater quality in Al-Hillah city was rated as poor for drinking uses.
3.3 Producing of Distribution Map of Groundwater for Drinking Uses
For Al-Hillah city, the distribution map of groundwater for drinking uses using the GW.Q.I. method can be seen in Fig. 5. Then, based on the GW.Q.I. values, Fig. 6 shows the distribution map of groundwater rating for drinking.
Areas and their proportions of GW.Q.I. and GW.Q.R. in Al-Hillah city that resulted from Figs. 5 and 6 can be seen in Table 7. The values of valid areas that can be used for drinking and other uses cover 126.8 km2 (14.75%) of the entire area of Al-Hillah city 860 km2, which were rated as excellent and good. Otherwise, about 7% of the total areas were considered unacceptable for drinking uses, rated as contaminated and very contaminated.
4 Conclusion
This study has been set to rate the groundwater quality for drinking uses. It is interesting to study the groundwater employed to use in several daily uses that will be extracted from wells distributed in different areas in Al-Hillah city. Therefore, the groundwater quality index model was applied to determine groundwater quality and its suitability for drinking before use by humans. A comparison has been done for the groundwater in the study area with the local groundwater and international standards.
The distribution maps for groundwater have been established using the groundwater quality index for drinking uses and entered into the GIS for this purpose. The produced maps will ease researchers and scientists to determine the quality of groundwater and help them know its ranges and distribution in the study area. The IDW method and the GIS were combined to produce interpolation maps for groundwater quality for drinking uses using twelve variables measured in 56 wells within Al-Hillah city.
The twelve variables entered in the weighted arithmetic method to calculate the groundwater quality index for drinking uses are Ca, Mg, Na, k, C, SO4, HCO3, TH, TDS, NO3, and EC. Based on the GW.Q.I. values, the generated map of groundwater quality was rated into six categories ranging from excellent to very contaminated.
For each variable, the prediction map was produced as a distribution map to cover the whole study area by using the prediction method IDW as a tool existing in the GIS.
The results showed that the generated map for the groundwater quality index in Al-Hillah city was classified and rated into six categories for drinking uses. These categories were occupied (in km2) 5.1, 121.7, 609.9, 63.4, 35.9, and 24.0 km2 with a rating of excellent, good, poor, very poor, contaminated, and very contaminated, respectively. For the selected wells, the average value of the groundwater quality index for drinking uses in Al-Hillah city was about 177; consequently, it was classified as poor water (P-GW) for drinking uses.
In general, the new map of the groundwater classification is significant for future works. These maps provide valuable information on the groundwater status at each well in the study area using some physical and chemical variables. It can be a new guide for academic, agricultural, and industrial specialists.
Data Availability
All data are included within the text.
References
Abbas, J. (2013). Assessment of water quality in Tigris River-Iraq by using GIS mapping. Natural Resources, 4, 441–448. https://doi.org/10.4236/nr.2013.46054
Ali, S.K. (2017). Assessment of the Tigris River water quality in selected Iraqi governments. International Journal of Science and Research, 7; 500 - 504. https://doi.org/10.21275/ART20179406
Alikhan, H. A., Hussein, A. K., & Alshukri, A. S. (2020). Groundwater quality assessment using water quality index: A case study of Al Najaf City, Iraq. Periodicals of Engineering and Natural Sciences (PEN), 8(3), 1482–1490. https://doi.org/10.21533/pen.v8i3.1456
Al-Jiburi, H. K., & Al-Basrawi, N. H. (2011). Hydrogeology of the Mesopotamia plain. Iraqi Bulletin of Geology and Mining, 4, 83–103.
Al-Madhlom, Q., Nordell, B., Chabuk, A., Al-Ansari, N., Lindblom, J., Laue, J., & Hussain, H. M. (2020). Potential use of UTES in Babylon Governorate. Iraq. Groundwater for Sustainable Development, 10, 100283. https://doi.org/10.1016/j.gsd.2019.100283
Alobaidy, A. H. M. J., Maulood, B. K., & Kadhem, A. J. (2010). Evaluating raw and treated water quality of Tigris River within Baghdad by index analysis. Journal of Water Resource and Protection, 2(7), 629.
Alsaqqar, A. S., Hashim, A., & Mahdi, A. (2015). Water quality index assessment using GIS case study: Tigris River in Baghdad City. International Journal of Current Engineering and Technology, 5(4), 2515–2520. http://inpressco.com/category/ijcet. Accessed Aug 2015.
Bouderbala, A. (2017). Assessment of water quality index for the groundwater in the upper Cheliff plain, Algeria. Journal of the Geological Society of India, 90(3), 347–356. https://doi.org/10.1007/s12594-017-0723-7
Chabuk, A., Al-Maliki, A., Al-Ansari, N., & Laue, J. (2020). Evaluation of the groundwater quality for irrigation: Case study of Hilla district, Babylon Province, Iraq. In IOP Conference Series: Materials Science and Engineering (Vol. 928, No. 2, p. 022056). IOP Publishing. https://doi.org/10.1088/1757-899X/928/2/022056
Chabuk A. J., Al-Ansari, N., & Laue, J. (2021). Site selection criteria and design for landfills in an arid area with shallow groundwater depth. Environmental Science and Engineering (ESE), pp 233–238. https://doi.org/10.1007/978-3-030-51210-1_39.
Iraqi Ministry of Planning. (2017). Records of directorate of census Babylon, internal reports, Baghdad: Iraqi Ministry of Planning.
Iraqi Ministry of transportation constitutions. (2019). Iraqi meteorological organization & seismology. Internal reports Baghdad: Iraqi Ministry of Transportation constitutions.
Iraqi Ministry of Water Resources. (2017). General commission for groundwater. Internal reports, Baghdad: Iraqi Ministry of Water Resources Iraqi Ministry of Water Resources.
Krishan, G., Singh, S., Kumar, C. P., Garg, P., Suman, G., Ghosh, N. C., & Chaudhary, A. (2016). Assessment of groundwater quality for drinking purpose by using water quality index (WQI) in Muzaffarnagar and Shamli Districts, Uttar Pradesh. India. Hydrol Current Research, 7(227), 4. https://doi.org/10.4172/2157-7587.10002
Mohammed, N. I., Abduljabar, K. A., Mahdi, H. S., Abdullah, H. M., & Youssef, S. (2020). Groundwater quality assessment of Domiz refugee camp in Duhok governorate, Kurdistan region, Iraq. Zanco Journal of Pure and Applied Sciences, 32(4), 157–168. https://doi.org/10.21271/ZJPAS.32.4.19
Othman, B. A., & Ibrahim, E. S. (2021). Assessment of groundwater quality over the Erbil Plain based on water quality index. Zanco Journal of Pure and Applied Sciences, 33(S1), 1–10. https://doi.org/10.21271/ZJPAS.33.s1.1
Panhalkar, S. S., & Jarag, A. P. (2016). Assessment of spatial interpolation techniques for river bathymetry generation of Panchganga River basin using geoinformatic techniques. Asian Journal of Geoinformatics, 15(3).
Sissakian, V. K. (2013). Geological evolution of the Iraqi Mesopotamia Foredeep, inner platform and near surroundings of the Arabian Plate. Journal of Asian Earth Sciences, 72, 152–163. https://doi.org/10.1016/j.jseaes.2012.09.032
Tyagi, S., Sharma, B., Singh, P., & Dobhal, R. (2013). Water quality assessment in terms of water quality index. American Journal of water resources, 1(3), 34–38. https://doi.org/10.12691/ajwr-1-3-3
Walsh, P., & Wheeler, W. (2012). Water quality index aggregation and cost benefit analysis. 4, pp 81–105, (No. 2168–2018–8142).
World Health Organization (WHO). (2017). Guidelines for drinking water quality, first addendum (4th ed.). WHO.
Acknowledgements
The authors would like to present extreme thanks to the General Commission for Groundwater, Iraqi Ministry of Water Resources, Baghdad, Iraq, to provide the authors with the readings of variables for the groundwater measured in the Al-Hillah city, Babylon, Iraq.
Funding
Open access funding provided by Lulea University of Technology. Open access funding provided by Lulea University of Technology, Sweden, and Al-Mustaqbal University College, Iraq, supported the present research by the fund.
Author information
Authors and Affiliations
Contributions
Conceptualization: Ali Chabuk, Udai A. Jahad; Methodology: Ali Chabuk, Ali Majdi, Udai A.Jahad; Formal analysis: Ali Chabuk, Udai A. Jahad, Ali Majdi, Nadhir Al-Ansari, Salwan Ali, Mubeen Isam; Writing —original draft preparation: Ali Chabuk, Udai A. Jahad, Mubeen Isam, Nadhir Al-Ansari, Salwan Ali and Jan Laue; Writing—review and editing: Ali Chabuk, Udai A. Jahad, Ali Majdi, Nadhir Al-Ansari, Jan Laue, Salwan Ali; Funding acquisition: Nadhir Al-Ansari, Ali Majdi, Hasan SH. Majdi; Supervision: Nadhir Al-Ansari, Jan Laue, Hasan SH. Majdi and Salwan Ali.
Corresponding author
Ethics declarations
Conflict of Interest
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Chabuk, A., Jahad, U.A., Majdi, A. et al. Creating the Distribution Map of Groundwater for Drinking Uses Using Physio-Chemical Variables; Case Study: Al-Hilla City, Iraq. Water Air Soil Pollut 233, 218 (2022). https://doi.org/10.1007/s11270-022-05660-3
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11270-022-05660-3