Abstract
It was recently reported that, besides UV irradiated polymerization, polymerization of diacetylene compounds could also been initiated by radicals generated from enzyme catalyzed hydrogen peroxide (H2O2) decomposition. A new optical sensing method for H2O2 was proposed based on this phenomenon. However, the sensitivity of this method is relatively lower than existed ones. In the present work, phenylboronic acid (PBA) functionalized 10, 12-pentacosadiynoic acid (PDA-PBA) was synthesized and its vesicles were formed successfully as colorimetric sensor for H2O2 detection. It was found that color change during the polymerization of vesicles composed of the PBA modified monomer is much stronger than that of the non-modified one. The response of PDA-PBA vesicles to H2O2 is 16 times more sensitive than that of the PDA. The absorption of PDA-PBA at 650 nm is linearly related to the concentration of H2O2 and a detection limit of ~5 μM could be achieved.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Hydrogen peroxide (H2O2) has been widely used in bleaching, cleaning and disinfection [1]. It is also a by-product of oxidative metabolism [2]. The detection of H2O2 is of practical importance in food, clinical, modern medicine, environmental monitoring and various other industries [3, 4]. Many methods such as chemiluminescence [5, 6], electrochemical methods [7–9] and chromatography [10] have been developed for the detection of H2O2. However, these detection methods need either expensive instruments or reagents. Therefore, optical biosensors are of the significant interest for the detection of H2O2 due to their low cost and simple instruments [11].
Recently, conjugated polymer colorimetric biosensor has become popular due to its high sensitivity, selectivity and practicality [12–16]. We previously reported a free radical triggered polymerization of 10, 12-pentacosadiynoic acid (PCDA) vesicles as a colorimetric reagent for H2O2 detection [17]. The polymerization of well-packed diacetylene monomers can be induced by the hydroxyl radical produced from the horseradish peroxidase (HRP) catalyzed H2O2 decomposition reaction [18–20]. The color of the reaction mixture changes from colorless to blue during the polymerization. Under the optimal conditions, the colorimetric detection of H2O2 can be completed with 20 μg/mL HRP (pH = 7.0) at 30 °C in 30 min. However, the previously reported PCDA-based method showed a relatively higher detection limit of ca. 80 μM which has no advantage compared to other methods [17].
The topotactic polymerization of diacetylene is generally known to be acutely sensitive to the molecular order of molecular assemblies. So, the molecular assemblie of the diacetylene determines not only the ability to form stable vesicles but also its chromic behavior. Besides the total chain length and position of the diacetylenic unit within the chain, chemical nature of the headgroup is a key structural factor for diacetylene compounds. Interactions between neighboring diacetylene molecules via their headgroups are especially important for signal amplification in sensors and this could be tailored by synthesis [21]. Niwa et al. prepared LB film of 10, 12-pentacosadiynamide phenylboronic acid (DA-PBA) and got a blue polymer film upon UV irradiation [22]. It is found that dehydration of boronic acid groups constrained in position on the surface of a two dimensional monolayer assembly would form cross-linked boronic anhydrides. Lee et al. also successfully prepared phenylboronic acids functionialized diacetylene network films on solid substrates [23]. In the present work, a polydiacetylene vesicle bearing phenylboronic acid group was prepared for the first time and used as a more sensitive colorimetric biosensor for H2O2 detection.
Synthetic Routes
Purification of PCDA
The commercial PCDA was purified for further use. Briefly, PCDA solid powder was dissolved in methylene chloride and filtered through 0.45 μm membrane to remove the poly-PCDA. The methylene chloride was evaporated with a rotary evaporator and the resultant PCDA monomer was stored at −20 °C in the dark.
Synthesis of APCDA
Figure 1 shows the synthesis route for the mediate product 10,12-pentacosadiynoic acid 2-aminoacetamide (APCDA). Briefly, 2.45 mmol purified PCDA monomer in 20 mL tetrahydrofuran was mixed with 2.4 mmol N-hydroxysuccinimide and 2.45 mmol 1-ethyl-3(3-dimethyl ammonium propyl)-carbodiimide. The mixed solution was allowed to react for 24 h under 350 rpm mechanical stirring in the dark. The reaction solution was then evaporated to dryness with the rotary evaporator. The dried residue was re-dissolved in 30 mL chloroform and extracted with 20 mL saturated sodium chloride solution 6 times. The organic phase was collected and dried over anhydrous magnesium sulfate for 12 h. The product was dissolved in 50–70 mL chloroform. Ten milliliters ethylenediamine (4 mmol in dichloromethane) was added to the product solution dropwise. The pH of the solution was adjusted to 9.0 with triethylamine. The reaction was allowed to precede under 300 rpm mechanical at 30 °C in the dark. The reaction solution was then evaporated to dryness and the product, APCDA, was purified on a silica gel column with an eluant of chloroform: methyl alcohol (5:1). The yield of APCDA is 83–94 %. Figure 2 is the 1HNMR of APCDA and data are as follows: 1HNMR (300 MHz, CDCl3): δ(ppm) 0.78–0.81(t, J = 9, 3 H), 1.11–1.85 (m, 36 H), 2.14–2.16 (t, J = 6, 3 H), 2.24–2.26(t, J = 6, 2 H), 3.31–3.34(dd, J = 9, 2 H), 7.19(brs, 1 H).
Synthesis of APCDA-PBA
The synthesis route of APCDA-PBA is present in Fig.3. Ten grams of 4-carboxyphenylboronic acid (PBA, 60.3 mmol) were added into a two-necked flask. Thionyl chloride (150 ml) was then added to the flask in a N2 atmosphere. The mixture was magnetically stirred (350 rpm) for 24 h at 88 °C. The reaction mixture was then evaporated to dryness and the dry residue was re-dissolved in 60 ml anhydrous tetrahydrofuran. Chloroform (20 ml) was added dropwise to 3 mmol of APCDA in a N2 atmosphere with an ice-bath. A drop of dimethyl formamide (DMF) was added after 30 min and kept in the ice-bath for another 2 h in the dark. After that, the obtained mixture was added dropwise to the previous prepared PBA solution and allowed to react for 20 h in the dark. The reaction mixture was evaporated to dryness with the rotary evaporator and the product was purified on a silica gel column with an eluant of chloroform: methyl alcohol (7:1). The yield of APCDA-PBA is between 91 and 94 %. Figure 4 is the 1HNMR of APCDA-PBA and data are as follows: 1HNMR (300 MHz, CDCl3): δ(ppm) 0.78–0.81(t, J = 9, 3 H), 1.18–1.58(m, 36 H), 2.14–2.17(t, J = 9, 4 H), 2.35–2.37(t, J = 6, 2 H), 2.87(s, 1 H), 2.94(s, 1 H), 7.05–7.06(d, J = 3, 2 H), 7.19(brs, 2 H), 7.84–7.86 (d, J = 6, 2 H)..
Preparation of APCDA-PBA Vesicle
The produced APCDA-PBA (14.98 mg) was dissolved in 4 ml DMSO and 36 ml distilled water, heated to 70 °C and sonicated for 15 min. The solution was filtered and stored at 4 °C in the dark overnight.
Results and Discussion
Characterization of APCDA-PBA
The reaction substrate (PCDA), mediate product (APCDA) and product (APCDA-PBA) were confirmed with FTIR (Fig.5). The asymmetric stretching vibrations of CH2 groups of the diacetylene side chains can be found at 2928 cm−1 and 2852 cm−1. The peak at 2349 cm−1 can be ascribed to the vibrations of the unsaturated double bond CH = CH in the diacetylene monomer. These feature FTIR peaks are shared by all three different diacetylene derivatives. APCDA showed an absorption peak at 3324 cm−1, which was assigned to the stretching vibrations of N-H bond in amide. The absorption peaks at 1697 cm−1 and 1632 cm−1 can be assigned to the stretching vibrations of hydrogen-bonded carbonyl in carboxy bond and the stretching vibrations of hydrogen-bonded carbonyl in amide, respectively. The new peak at 1070 cm−1 is ascribed to the C-N bond in amide. These results indicate that the ethylene diamine monomer was successfully coupled with the PCDA. APCDA-PBA showed three new absorption peaks at 1810 cm−1, 860 cm−1 and 1551 cm−1, which were assigned to the stretching vibrations of C = C and stretching vibrations of C-H and B-O, respectively. These indicate that phenylboronic acid was coupled with the APCDA successfully.
The microstructures of poly-PCDA and poly-APCDA-PBA vesicles were imaged with a SEM (Fig.6). The poly-PCDA vesicles are composed of large spherical particles, while poly-APCDA-PBA vesicles composite of smaller rod-shaped and square particles. This can be explained that amphiphilic monomers with achiral headgroups usually form spherical liposomes and chiral amphiphiles form non-spherical structures such as helices and tubules [24]. Similar small particles can also be found in polydiacetylene-amino/1, 2-dimyristoyl-SN-glycero-3 -phosphocholine (PDA/DMPC) mixed vesicles, which can improve the UV-Vis absorption of the vesicles and enhance the color change [25]. The PDA/DMPC mixed vesicle coupled with antigen has a flat shape, which can be attributed to its inherent variability and instability in preparation process [26]. Morphology change of vesicles can usually affect their detection sensitivities and stabilities [27–29]. The smaller vesicles provide more surface binding sites and thus improve the detection sensitivity of the colorimetric method [30].
UV Light Trigged Polymerization
The polymerization of diacetylene vesicles is initiated by UV light. The effects of irradiation time on the polymerization process of PCDA and APCDA-PBA were investigated. The absorption of the poly-PCDA at 650 nm (A650) increased from 0.06 to 0.21 when the irradiation time was increased from 1 min to 2 min (Fig.7a). Meanwhile, A650 of poly-APCDA-PBA reached as high as 0.65 with 1 min irradiation. When irradiation time was increased to 2 min, the blue phase of poly-APCDA-PBA shifted to the purple phase and an absorption peak appeared at 550 nm. A650 did not show significantly change. Thus, 1 min UV irradiation time is enough for the polymerization of APCDA-PBA. These also indicate that the polymerization of APCDA-PBA is easier to be trigged than that of PCDA alone. The much higher absorption of the poly-APCDA-PBA in blue region (Fig.7b) indicates the high sensitive of colorimetric method with APCDA-PBA vesicle.
Detection of H2O2 with APCDA-PBA Vesicle
The potential application of APCDA-PBA vesicles in the quantification of H2O2 was explored. Figure 8a shows the UV-Vis absorption spectra of APCDA-PBA vesicles polymerized with various concentration of H2O2 ranging from 0 to 100 mM. It is clear the peak absorption at 650 nm increased with the increase of H2O2 concentration. APCDA-PBA vesicles can respond to as low as 5 μM H2O2, which is 16 times more sensitive than PCDA vesicles. In addition, the absorption of APCDA-PBA vesicles at 650 nm is significantly higher than that of PCDA vesicles [17] under same conditions, which is consistent with the results of its UV-induced polymerization reaction (Fig.7b). Figure 8c shows the images of APCDA-PBA vesicles being polymerized with the different concentration of H2O2 from 5 μM to 100 mM. It is clear that the intensity of the blue color is significantly increased with the increase of the concentration of H2O2 and the color change of APCDA-PBA vesicles is more dramatic than that of PCDA vesicles [17] under same conditions.
The possibility of the quantification of H2O2 with APCDA-PBA vesicles was explored. The relationship between the absorption of poly-APCDA-PBA at 650 nm and the concentration of H2O2 is fitted in a linear regression logA = −0.719+ 0.187logc (R2 = 0.991, n = 7) (Fig.8b), where A is the absorbance of poly-APCDA-PBA at 650 nm and c is the concentration of H2O2 in μM. The lowest detectable concentration of H2O2 is ~5 μM.
Conclusions
In summary, the response of polydiacetylene vesicles to H2O2 can be effectively enhanced by the introduction of phenylboronic acid group. The absorption of PDA-PBA vesicles at 650 nm and the concentration of H2O2 are linearly related. The detection limit of the PDA-PBA vesicle based colorimetric method is ~5 μM H2O2, which is 16 times lower than that of the PDA vesicles based colorimetric method. The PDA-PBA vesicle is a promising tool for the detection of H2O2 in modern medicine, environmental and biotechnology monitoring.
References
Petlicki J, Palusova D, van de Ven TGM (2005) Physicochemical aspects of catalytic decomposition of hydrogen peroxide by manganese compounds. Ind Eng Chem Res 44:2002–2010. doi:10.1021/ie049595n
Root R, Metcalf J, Oshino N, Chance B (1975) H2O2 release from human granulocytes during phagocytosis. I. documentation, quantitation, and some regulating factors. J Clin Investig 55:945–955. doi:10.1172/JCI108024
Stuart A. G. Evans, Joanne M. Elliott, Lynn M. Andrews, Philip N. Bartlett et al (2002) Detection of hydrogen peroxide at mesoporous platinum microelectrodes. Anal Chem 74: 1322–1326. doi:10.1021/ac011052p
Lei C-X, Hu S-Q, Shen G-L, Yu R-Q (2003) Immobilization of horseradish peroxidase to a nano-Au monolayer modified chitosan-entrapped carbon paste electrode for the detection of hydrogen peroxide. Talanta 59:981–988. doi:10.1016/S0039-9140(02)00641-0
He S, Shi W, Zhang X, Li J, et al (2010) β-cyclodextrins-based inclusion complexes of CoFe2O4 magnetic nanoparticles as catalyst for the luminol chemiluminescence system and their applications in hydrogen peroxide detection. Talanta 82:377–383. doi:10.1016/j.talanta.2010.04.055
Han JH, Jang J, Kim BK, Choi HN, et al (2011) Detection of hydrogen peroxide with luminol electrogenerated chemiluminescence at mesoporous platinum electrode in neutral aqueous solution. J Electroanal Chem 660:101–107. doi:10.1016/j.jelechem.2011.06.012
Pajor-Swierzy A, Kolasinska-Sojka M, Warszynski P (2014) The electroactive multilayer films of polyelectrolytes and Prussian blue nanoparticles and their application for H2O2 sensors. Colloid Polym Sci 292:455–465. doi:10.1007/s00396-013-3091-x
Fan J, Bian X, Niu Y, Bai Y, et al (2013) Formation of three-dimensional Nano-porous silver films and application toward electrochemical detection of hydrogen peroxide. Appl Surf Sci 285:185–189. doi:10.1016/j.apsusc.2013.08.034
Rismetov B, Ivandini TA, Saepudin E, Einaga Y (2014) Electrochemical detection of hydrogen peroxide at platinum-modified diamond electrodes for an application in melamine strip tests. Diam Relat Mater 48:88–95. doi:10.1016/j.diamond.2014.07.003
Nakashima K, Wada M, Kuroda N, Akiyama S, et al (1994) High-performance liquid chromatographic determination of hydrogen peroxide with peroxyoxalate chemiluminescence detection. J Liq Chromatogr 17:2111–2126. doi:10.1080/10826079408013535
Shiang YC, Huang CC, Chang HT (2009) Gold nanodot-based luminescent sensor for the detection of hydrogen peroxide and glucose. Chem Commun 23:3437–3439. doi:10.1039/b901916b
Kim JM, Lee YB, Yang DH, et al (2005) A polydiacetylene-based fluorescent sensor chip. J Am Chem Soc 127:17580–17581. doi:10.1021/ja0547275
Kolusheva S, Molt O, Herm M, et al (2005) Selective detection of catecholamines by synthetic receptors embedded in chromatic polydiacetylene vesicles. J Am Chem Soc 127:10000–10001. doi:10.1021/ja052436q
Wu A, Yuan G, Tian H, Federici JF, et al (2014) Effect of alkyl chain length on chemical sensing of polydiacetylene and polydiacetylene/ZnO nanocomposites. Colloid Polym Sci 292:3137–3146. doi:10.1007/s00396-014-3365-y
Pecher J, Mecking S (2010) Nanoparticles of conjugated polymers. Chem Rev 110:6260–6279. doi:10.1021/cr100132y
Song YJ, Wei WL, Qu XG (2011) Colorimetric biosensing using smart materials. Adv Mater 23:4215–4236. doi:10.1002/adma.201101853
Lu S, Jia C, Duan X, Zhang X, et al (2014) Polydiacetylene vesicles for hydrogen peroxide detection. Colloid Surf A 443:488–491. doi:10.1016/j.colsurfa.2013.11.029
Wen F, Dong YH, Feng L, Wang S, et al (2011) Horseradish peroxidase functionalized fluorescent gold nanoclusters for hydrogen peroxide sensing. Anal Chem 83:1193–1196. doi:10.1021/ac1031447
Wu P, Cai Z, Chen J, Zhang H, et al (2011) Electrochemical measurement of the flux of hydrogen peroxide releasing from RAW 264.7 macrophage cells based on enzyme-attapulgite clay nanohybrids. Biosens Bioelectron 26:4012–4017. doi:10.1016/j.bios.2011.03.018
Tahir MN, André R, Sahoo JK, Jochum FD, et al (2011) Hydrogen peroxide sensors for cellular imaging based on horse radish peroxidase reconstituted on polymer-functionalized TiO2 nanorods. Nanoscale 3:3907–3914. doi:10.1039/c1nr10587f
Jonas U, Shah K, Norvez S, et al (1999) Reversible color switching and unusual solution polymerization of hydrazide-modified diacetylene lipids. J Am Chem Soc 121:4580–4588. doi:10.1021/ja984190d
Niwa M, Shibahara S, Higashi N (2000) Diacetylenic monolayers containing a boronic acid moiety form a chemically and thermally stable poly(diacetylene) film on water. J Mater Chem 10:2647–2651. doi:10.1039/b004371k
Lee J, Yarimaga O, Lee CH, Choi YK, et al (2011) Network polydiacetylene films: preparation, patterning, and sensor applications. Adv Funct Mater 21:1032–1039. doi:10.1002/adfm.201002042
Reppy MA, Pindzola BA (2007) Biosensing with polydiacetylene materials: structures, optical properties and applications. Chem Commun 14(42):4317–4338. doi:10.1039/b703691d
Evrard D, Touitou E, Kolusheva S, Fishov Y, et al (2001) A new colorimetric assay for studying and rapid screening of membrane penetration enhancers. Pharm Res 18:943–949. doi:10.1023/A:1010980009823
Su Y, Li J, Jiang L (2004) Effect of amphiphilic molecules upon chromatic transitions of polydiacetylene vesicles in aqueous solutions. Colloids Surf B: Biointerfaces 39:113–118. doi:10.1016/j.colsurfb.2003.12.005
Lee J, Jeong EJ, Kim J (2011) Selective and sensitive detection of melamine by intra/inter liposomal interaction of polydiacetylene liposomes. Chem Commun 47:358–360. doi:10.1039/c0cc02183k
Lee SW, Kang CD, Yang DH, et al (2007) The development of a generic bioanalytical matrix using polydiacetylenes. Adv Funct Mater 17:2038–2044. doi:10.1002/adfm.200600398
Guo CX, Boullanger P, Liu T, Jiang L (2005) Size effect of polydiacetylene vesicles functionalized with glycolipids on their colorimetric detection ability. J Phys Chem B 109:18765–18771. doi:10.1021/jp052580y
Schneider HJ, Tianjun L, Lomadze N (2004) Sensitivity increase in molecular recognition by decrease of the sensing particle size and by increase of the receptor binding site - a case with chemomechanical polymers. Chem Commun 21:2436–2437. doi:10.1039/b409331c
Acknowledgments
This work was supported by the National Science Foundation for Distinguished Young Scholars of China (No.21225626) and the Key Program of the National Natural Science Foundation of China (No.20936002).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Jia, C., Tang, J., Lu, S. et al. Enhanced Sensitivity for Hydrogen Peroxide Detection: Polydiacetylene Vesicles with Phenylboronic Acid Head Group. J Fluoresc 26, 121–127 (2016). https://doi.org/10.1007/s10895-015-1691-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10895-015-1691-1