Abstract
This paper presents a novel two degrees of freedom (DOFs) contact force control method for robotic blisk grinding. The grinding tool is controlled to automatically adapt to the curvity change of the blisk blade and maintain a constant contact force as expected. A smart end effector is used as the actuating device for contact force control. The proposed force controller includes a gravity compensation module, a force prediction module, and a force-position controller. The direction and amplitude of the contact force are predicted with the force prediction module and are controlled with the force-position controller. The tool path of the robotic blisk grinding process is generated and optimized so that the contact points between the tool tip and the workpiece are evenly distributed along the grinding path. Both simulations and experiments are carried out to validate the effectiveness of the proposed method. The results show that the proposed method provides a good contact force control performance, with less than 1 N force fluctuation. The surface finish and roughness are significantly improved compared to the case without force control. The grinding efficiency is raised by about sixfold compared to the case with one DOF force control.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Xu X, Zhu D, Zhang H, Yan S, Ding H (2017) TCP-based calibration in robot-assisted belt grinding of aero-engine blades using scanner measurements. Int J Adv Manuf Technol 90:635–647. https://doi.org/10.1007/s00170-016-9331-8
Liang W, Kang X, Zhao W, Yang Y (2016) Electrical discharge machining of electron beam melting formed shrouded blisk. Int J Adv Manuf Technol 87:2319–2326. https://doi.org/10.1007/s00170-016-8545-0
Ren JX, Yao CF, Zhang DH, Xue YL, Liang YS (2009) Research on tool path planning method of four-axis high-efficiency slot plunge milling for open blisk. Int J Adv Manuf Technol 45:101–109. https://doi.org/10.1007/s00170-009-2153-1
Zhang J, Shi Y, Lin X, Li Z (2017) Parameter optimization of five-axis polishing using abrasive belt flap wheel for blisk blade. J Mech Sci Technol 31:4805–4812. https://doi.org/10.1007/s00170-017-0717-z
Huang H, Gong ZM, Chen XQ, Zhou L (2002) Robotic grinding and polishing for turbine-vane overhaul. J Mater Process Technol 127:140–145. https://doi.org/10.1016/S0924-0136(02)00114-0
Duan J, Zhang Y, Shi Y (2016) Belt grinding process with force control system for blade of aero-engine. Proc Inst Mech Eng Part B J Eng Manuf 230:858–869. https://doi.org/10.1177/0954405414563420
Zhao P, Shi Y (2014) Posture adaptive control of the flexible grinding head for blisk manufacturing. Int J Adv Manuf Technol 70:1989–2001. https://doi.org/10.1007/s00170-013-5438-3
Xiao G, Huang Y (2015) Constant-load adaptive belt polishing of the weak-rigidity blisk blade. Int J Adv Manuf Technol 78:1473–1484. https://doi.org/10.1007/s00170-014-6724-4
Xiao G, Huang Y (2016) Equivalent self-adaptive belt grinding for the real-R edge of an aero-engine precision-forged blade. Int J Adv Manuf Technol 83:1697–1706. https://doi.org/10.1007/s00170-015-7680-3
Xiao G, Huang Y, Yin J (2017) An integrated polishing method for compressor blade surfaces. Int J Adv Manuf Technol 88:1723–1733. https://doi.org/10.1007/s00170-016-8891-y
Roswell A, Xi F, Liu G (2006) Modelling and analysis of contact stress for automated polishing. Int J Mach Tools Manuf 46:424–435. https://doi.org/10.1016/j.ijmachtools.2005.05.006
Thomessen T, Lien TK, Sannñs PK (2001) Robot control system for grinding of large hydro power turbines. Ind Robot An Int J 28:328–334
Dai H, Yuen KM, Elbestawi MA (1993) Parametric modelling and control of the robotic grinding process. Int J Adv Manuf Technol 8:182–192
Minami M, Asakura T, Dong LX, Huang YM (1996) Position control and explicit force control of constrained motions of a manipulator for accurate grinding tasks. Adv Robot 11:285–300. https://doi.org/10.1163/156855397X00254
Sun Y, Giblin DJ, Kazerounian K (2009) Accurate robotic belt grinding of workpieces with complex geometries using relative calibration techniques. Robot Comput Integr Manuf 25:204–210. https://doi.org/10.1016/j.rcim.2007.11.005
Pan Z, Zhang H (2008) Robotic machining from programming to process control:a complete solution by force control. Ind Robot An Int J 35:400–409. https://doi.org/10.1109/WCICA.2008.4594434
Zhang J, Liu G, Zang X (2016) A hybrid passive / active force control scheme for robotic belt grinding system. In: Proceedings of 2016 IEEE international conference on mechatronics and automation, August 7–10,Harbin, China
Chen SY, Zhang T, Zou YB (2017) Fuzzy-sliding mode force control research on robotic machining. J Robot 2017:1–8. https://doi.org/10.1155/2017/8128479
Liao L, Xi F, Liu K (2008) Modeling and control of automated polishing/deburring process using a dual-purpose compliant toolhead. Int J Mach Tools Manuf 48:1454–1463. https://doi.org/10.1016/j.ijmachtools.2008.04.009
Acknowledgements
This research is supported by the National Natural Science Foundation of China (Grant Nos. 51705175, 91748114 and 51535004) and the China Postdoctoral Science Foundation (Grant No. 2017M612444).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Chen, F., Zhao, H., Li, D. et al. Robotic grinding of a blisk with two degrees of freedom contact force control. Int J Adv Manuf Technol 101, 461–474 (2019). https://doi.org/10.1007/s00170-018-2925-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2925-6