Abstract
Experimental data is presented relating to heat-affected zone (HAZ) and surface quality when using continuous wave (CW) fiber laser cutting carbon fiber reinforced plastic (CFRP) with varying configurations including + 45°/− 45°, 0°/90°, and plain woven. The effect of typical cutting parameters including laser power, cutting speed, and assist gas pressure on laser cutting quality of different type of workpiece materials was investigated. A full factorial experimental array was employed involving 24 trials. The statistical significance of individual cutting parameters was determined using main effects plot together with ANOVA. Results showed that the fiber laser was feasible for cutting CFRP with very high efficiency. The HAZ level of laser cutting CFRP was highly related to fiber orientation, laser power, and cutting speed based on theoretical and statistical analysis. Thermal model was built to simulate HAZ values recorded on the exit surface. The calculated results were close (within ~ 60 μm) to the experimental results. The lowest HAZ value of 707 μm and surface roughness of 2.43-μm surface roughness were achieved in cutting Type 1 (+ 45°/− 45°) configuration. High-resolution SEM and optical micrographs showed that cracks, cavities, delamination, and matrix decomposition were the typical defects observed in CW fiber laser cutting of CFRP laminates.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Turki Y, Habak M, Velasco R, Vantomme P (2017) Highlighting cutting mechanisms encountered in carbon/epoxy composite drilling using orthogonal cutting. Int J Adv Manuf Technol 92(1):685–697. https://doi.org/10.1007/s00170-017-0153-0
Liu D, Tang Y, Cong WL (2012) A review of mechanical drilling for composite laminates. Compos Struct 94(4):1265–1279. https://doi.org/10.1016/j.compstruct.2011.11.024
Shanmugam DK, Nguyen T, Wang J (2008) A study of delamination on graphite/epoxy composites in abrasive waterjet machining. Compos A Appl Sci Manuf 39(6):923–929. https://doi.org/10.1016/j.compositesa.2008.04.001
MM IW, Azmi AI, Lee CC, Mansor AF (2018) Kerf taper and delamination damage minimization of FRP hybrid composites under abrasive water-jet machining. Int J Adv Manuf Technol 94:1727–1744. https://doi.org/10.1007/s00170-016-9669-y
Shanmugam DK, Chen FL, Siores E, Brandt M (2002) Comparative study of jetting machining technologies over laser machining technology for cutting composite materials. Compos Struct 57(1):289–296. https://doi.org/10.1016/S0263-8223(02)00096-X
Sheikh-Ahmad JY (2009) Machining of polymer composites. Springer US, New York
Nagesh S, Narasimha Murthy HN, Pal R, Supreeth Dev SD, Krishna M (2017) Investigation of the effect of nanofillers on the quality of CO2 laser cutting of FRP nanocomposites. Int J Adv Manuf Technol 90(5):2047–2061. https://doi.org/10.1007/s00170-016-9535-y
Krot K, Chlebus E, Kuźnicka B (2017) Laser cutting of composite sandwich structures. Arch Civ Mech Eng 17(3):545–554. https://doi.org/10.1016/j.acme.2016.12.007
Tagliaferri V, Di Ilio A, Visconti C (1985) Laser cutting of fibre-reinforced polyesters. Compos 16(4):317–325. https://doi.org/10.1016/0010-4361(85)90284-8
Mathew J, Goswami GL, Ramakrishnan N, Naik NK (1999) Parametric studies on pulsed Nd:YAG laser cutting of carbon fibre reinforced plastic composites. J Mater Process Technol 89–90:198–203. https://doi.org/10.1016/S0924-0136(99)00011-4
Muramatsu M, Harada Y, Suzuki T, Niino H (2015) Infrared stress measurements of thermal damage to laser-processed carbon fiber reinforced plastics. Compos A Appl Sci Manuf 68:242–250. https://doi.org/10.1016/j.compositesa.2014.08.033
Li ZL, Zheng HY, Lim GC, Chu PL, Li L (2010) Study on UV laser machining quality of carbon fibre reinforced composites. Compos A Appl Sci Manuf 41(10):1403–1408. https://doi.org/10.1016/j.compositesa.2010.05.017
Leone C, Genna S, Tagliaferri V (2014) Fibre laser cutting of CFRP thin sheets by multi-passes scan technique. Opt Lasers Eng 53:43–50. https://doi.org/10.1016/j.optlaseng.2013.07.027
Gräf S, Staupendahl G, Krämer A, Müller FA (2015) High precision materials processing using a novel Q-switched CO2 laser. Opt Lasers Eng 66:152–157. https://doi.org/10.1016/j.optlaseng.2014.09.007
Salama A, Li L, Mativenga P, Sabli A (2016) High-power picosecond laser drilling/machining of carbon fibre-reinforced polymer (CFRP) composites. Appl Phys A Mater Sci Process 122(2):73. https://doi.org/10.1007/s00339-016-9607-8
Liu Y, Zhang R, Li W, Wang J, Yang X, Cheng L, Zhang L (2018) Effect of machining parameter on femtosecond laser drilling processing on SiC/SiC composites. Int J Adv Manuf Technol 96:1795–1811. https://doi.org/10.1007/s00170-017-1163-7
Cenna AA, Mathew P (1997) Evaluation of cut quality of fibre-reinforced plastics—a review. Int J Mach Tools Manuf 37(6):723–736. https://doi.org/10.1016/S0890-6955(96)00085-5
Negarestani R, Li L, Sezer HK, Whitehead D, Methven J (2010) Nano-second pulsed DPSS Nd:YAG laser cutting of CFRP composites with mixed reactive and inert gases. Int J Adv Manuf Technol 49(5):553–566. https://doi.org/10.1007/s00170-009-2431-y
Riveiro A, Quintero F, Lusquiños F, del Val J, Comesaña R, Boutinguiza M, Pou J (2012) Experimental study on the CO2 laser cutting of carbon fiber reinforced plastic composite. Compos A Appl Sci Manuf 43(8):1400–1409. https://doi.org/10.1016/j.compositesa.2012.02.012
Herzog D, Jaeschke P, Meier O, Haferkamp H (2008) Investigations on the thermal effect caused by laser cutting with respect to static strength of CFRP. Int J Mach Tools Manuf 48(12–13):1464–1473. https://doi.org/10.1016/j.ijmachtools.2008.04.007
Herzog D, Schmidt-Lehr M, Oberlander M, Canisius M, Radek M, Emmelmann C (2016) Laser cutting of carbon fibre reinforced plastics of high thickness. Mater Des 92:742–749. https://doi.org/10.1016/j.matdes.2015.12.056
Staehr R, Bluemel S, Jaeschke P, Suttmann O, Overmeyer L (2016) Laser cutting of composites-two approaches toward an industrial establishment. J Laser Appl 28(2):022203. https://doi.org/10.2351/1.4943754
Pan CT, Hocheng H (1998) Prediction of extent of heat affected zone in laser grooving of unidirectional fiber-reinforced plastics. J Eng Mater Technol 120(4):321–327. https://doi.org/10.1115/1.2807021
Chryssolouris G, Sheng P, Choi WC (1990) Three-dimensional laser machining of composite materials. J Eng Mater Technol 112(4):387–392. https://doi.org/10.1115/1.2903347
Caprino G, Tagliaferri V (1988) Maximum cutting speed in laser cutting of fiber reinforced plastics. Int J Mach Tools Manuf 28(4):389–398. https://doi.org/10.1016/0890-6955(88)90052-1
Cheng CF, Tsui YC, Clyne TW (1998) Application of a three-dimensional heat flow model to treat laser drilling of carbon fibre composites. Acta Mater 46(12):4273–4285. https://doi.org/10.1016/S1359-6454(98)00090-1
Wu CW, Wu XQ, Huang CG (2015) Ablation behaviors of carbon reinforced polymer composites by laser of different operation modes. Opt Laser Technol 73:23–28. https://doi.org/10.1016/j.optlastec.2015.04.008
Pan CT, Hocheng H (2001) Evaluation of anisotropic thermal conductivity for unidirectional FRP in laser machining. Compos A Appl Sci Manuf 32(11):1657–1667. https://doi.org/10.1016/S1359-835X(00)00093-2
Stock J, Zaeh MF, Conrad M (2012) Remote laser cutting of CFRP: improvements in the cut surface. Phys Procedia 39:161–170. https://doi.org/10.1016/j.phpro.2012.10.026
Funding
The authors would like to appreciate the financial support sponsored by “the Fundamental Research Funds for Central Universities (531107050870).”
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, M., Li, S., Yang, X. et al. Effect of lay-up configuration and processing parameters on surface quality during fiber laser cutting of CFRP laminates. Int J Adv Manuf Technol 100, 623–635 (2019). https://doi.org/10.1007/s00170-018-2728-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2728-9