Abstract
Manufacturing machine parts of high quality with high productivity and low cost is the most important goal of the production in metalworking industry. For the realization of production goals, single-objective optimization of the machining processes is a good way but multi-objective optimization is the right way. Turning is the most widely used machining process. Turning operation is usually realized through a multi-pass roughing and single-pass finishing. In this paper, multi-objective optimization of turning operation which consists of multi-pass roughing and single-pass finishing AISI 1064 steel with carbide cutting tool, in terms of material removal rate and machining cost, was studied. For multi-pass roughing, optimization problem with two objectives (material removal rate and machining cost), three factors (depth of cut, feed and cutting speed), and five machining constraints (cutting force, torque, cutting power, tool life, and cutting ratio) was studied. For single-pass finishing, optimization problem with two objectives (material removal rate and machining cost), four factors (tool nose radius, depth of cut, feed, and cutting speed), and three machining constraints (surface roughness, tool life, and cutting ratio) was studied. The optimization problem is solved using three techniques: (i) iterative search method, (ii) multi-objective genetic algorithm (MOGA), and (iii) genetic algorithm (GA). With the iterative search method, the values of objectives for all combinations of factor levels were calculated and an optimal solution was selected. With a multi-objective genetic algorithm, a set of optimal solutions named “Pareto optimal set” was defined and an optimal solution was selected. With a genetic algorithm, the optimal solution was determined by using the weighted-sum-type objective function.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Yusup N, Zain A, Hashim S (2012) Evolutionary techniques in optimizing machining parameters: review and recent applications (2007-2011). Expert Syst Appl 39(10):9909–9927
Onwubolu GC, Kumalo T (2001) Optimization of multi pass turning operations with genetic algorithms. Int J Prod Res 39(16):3727–3745
Chen MC, Tsai DM (1996) A simulated annealing approach for optimization of multi-pass turning operations. Int J Prod Res 34:2803–2825
Sahali M, Belaidi I, Serra R (2016) New approach for robust multi-objective optimization of turning parameters using probabilistic genetic algorithm. Int J Adv Manuf Technol 83(1):1265–1279
Yang S, Natarajan U (2010) Multi-objective optimization of cutting parameters in turning process using differential evolution and non-dominated sorting genetic algorithm-II approaches. Int J Adv Manuf Technol 49(5):773–784
Karpat Y, Ozel T (2007) Multi-objective optimization for turning processes using neural network modeling and dynamic-neighborhood particle swarm optimization. Int J Adv Manuf Technol 35(3–4):234–247
Abbas A, Hamza K, Aly M, Al-Bahkali E (2016) Multiobjective optimization of turning cutting parameters for J-steel material. Adv Mater Sci Eng 2016:1–8. https://doi.org/10.1155/2016/6429160
Kubler F, Bohner J, Steinhilper R (2015) Resource efficiency optimization of manufacturing processes using evolutionary computation: a turning case. Procedia CIRP 29:822–827
Wonggasem K, Wagner T, Trautmann H, Biermann D, Weihs C (2013) Multi-objective optimization of hard turning of AISI 6150 using PCA-based desirability index for correlated objectives. Procedia CIRP 12:13–18
Ganesan H, Mohankumar G (2013) Optimization of machining techniques in CNC turning centre using genetic algorithm. Arab J Sci Eng 38(6):1529–1538
Sardinas RQ, Mengana JEA, Davim P (2009) Multi-objective optimisation of multipass turning by using a genetic algorithm. Int J Mater Prod Technol 35(1–2):134–144
Emer DS, Kromodihardo S (1981) Optimization of multi-pass turning with constraints. J Eng Ind 103(4):462–468
Tan FP, Creese RC (1995) A generalized multi-pass machining model for machining parameter selection in turning. Int J Prod Res 33:1467–1487
Shin YC, Joo YS (1992) Optimization of machining conditions with practical constraints. Int J Prod Res 30:2907–2919
Lambert BK, Walvekar A (2007) Optimization of multi-pass machining operations. Int J Prod Res 16:259–265
Gupta R, Batra JL, Lal GK (1995) Determination of optimal subdivision of depth of cut in multi-pass turning with constraints. Int J Prod Res 33:2555–2565
Brutomizer (2018) http://www.virtuode.com/index.php/products/brutomizer/
Kovačević M, Madić M, Radovanović M, Rančić D (2014) Software prototype for solving multi-objective machining optimization problems: application in non-conventional machining processes. Expert Syst Appl 41(13):5657–5668
Kovačević M, Madić M, Radovanović M (2013) Software prototype for validation of machining optimization solutions obtained with meta-heuristic algorithms. Expert Syst Appl 40(17):6985–6996
Liepins GE, Hilliard MR (1989) Genetic algorithms: foundations and applications. Ann Oper Res 21:31–58
Tschatsch H (2009) Applied machining technology. Springer, New York
Iscar ltd (2000) Iscar turnplus. The complete range of turning tools
Funding
This work was carried out within the project TR 35034, financially supported by the Ministry of Science and Technological Development of the Republic of Serbia.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Radovanović, M. Multi-objective optimization of multi-pass turning AISI 1064 steel. Int J Adv Manuf Technol 100, 87–100 (2019). https://doi.org/10.1007/s00170-018-2689-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2689-z