Abstract
The microstructure and resultant mechanical properties of the hardened case produced in steels by induction surface hardening are discussed. The development of the final structure is followed throughout its characteristic evolutionary stages; its dependence on heating and cooling rate, maximum temperature of the treatment, composition, and initial microstructure is described in detail. Gradients of microstructure, composition, and hardness brought about by induction surface hardening inside the case are studied and explanations about their origin are proposed. The properties of the hardened case completely rely upon its microstructure, whose control is then a key factor for engineering applications.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gao K, Qin XP, Wang Z, Chen H, Zhu SX, Liu YX, Song YL (2014) Numerical and experimental analysis of 3D spot induction hardening of AISI 1045 steel. J Mater Process Technol 214(11):2425–2433. https://doi.org/10.1016/j.jmatprotec.2014.05.010
Shokouhmand H, Ghaffari S (2012) Thermal analysis of moving induction heating of a hollow cylinder with subsequent spray cooling: effect of velocity, initial position of coil, and geometry. Appl Math Model 36(9):4304–4323. https://doi.org/10.1016/j.apm.2011.11.058
Vieweg A, Ressel G, Prevedel P, Raninger P, Panzenböck M, Marsoner S, Ebner R (2016) Induction hardening: differences to a conventional heat treatment process and optimization of its parameters. IOP Conference Series: Materials Science and Engineering 119(1):012019
Kobayashi S, Takahashi H, Kamada Y (2013) Evaluation of case depth in induction-hardened steels: magnetic hysteresis measurements and hardness-depth profiling by differential permeability analysis. J Magn Magn Mater 343:112–118. https://doi.org/10.1016/j.jmmm.2013.04.082
Ceschini L, Martini C, Morri A (2015) Dry sliding wear of an induction-hardened, high-silicon medium-carbon microalloyed steel. Tribol Int 92:493–502. https://doi.org/10.1016/j.triboint.2015.07.032
Zhu SX, Wang Z, Qin XP, Mao HJ, Gao K (2016) Theoretical and experimental analysis of two-pass spot continual induction hardening of AISI 1045 steel. J Mater Process Technol 229:814–825. https://doi.org/10.1016/j.jmatprotec.2015.10.025
Gao K, Qin XP, Wang Z, Zhu SX (2016) Effect of spot continual induction hardening on the microstructure of steels: comparison between AISI 1045 and 5140 steels. Mat Sci Eng A 651:535–547. https://doi.org/10.1016/j.msea.2015.11.012
Lolla T, Cola G, Narayanan B, Alexandrov B, Babu SS (2011) Development of rapid heating and cooling (flash processing) process to produce advanced high strength steel microstructures. Mater Sci Technol 27(5):863–875. https://doi.org/10.1179/174328409x433813
Fett GA (2014) Induction case hardening of axle shafts. In: Rudnev V, Totten GE (eds) Induction heating and heat treatment, vol 4C. Vol ASM handbook. ASM International, pp 160–172
Li HP, He LF, Gai K, Jiang R, Zhang CZ, Li MS (2015) Numerical simulation and experimental investigation on the induction hardening of a ball screw. Mater Des 87:863–876. https://doi.org/10.1016/j.matdes.2015.08.094
Totik Y, Sadeler R, Altun H, Gavgali A (2003) The effects of induction hardening on wear properties of AISI 4140 steel in dry sliding conditions. Mater Des 24(1):25–30. https://doi.org/10.1016/S0261-3069(02)00099-7
Choi BY, Shin JH, Bahng GW, Yoon KB (1996) Metallographic study on rolling contact fatigue of 0.44%C-1.71%Mn induction-hardened bearing steels. Wear 192(1–2):1–5. https://doi.org/10.1016/0043-1648(95)06767-1
Rudnev V (2014) Principles of induction hardening and inspection. In: Rudnev VT, Totten G.E. (eds) Induction heating and heat treatment, ASM handbook Volume 4C. ASM International, pp 160–172
Clarke K (2008) The effect of heating rate and microstructural scale on austenite formation, austenite homogenization, and as-quenched microstructure in three induction hardenable steels. Ph.D. thesis, Colorado School of Mines, Golden, CO, USA
Ericsson T (1985) Thermal and austenitic thermochemical surface hardening of steel. In: Niku-Lari A (ed) Advances in surface treatments, vol 2. Pergamon Press, Oxford, pp 1–20
Rudnev V (2004) A common misassumption in induction hardening. Heat Treating Progress, vol SEPTEMBER/OCTOBER 2004
Brown D, Rudnev V, Dickson P (2014) Induction heating of billets, rods, and bars. In: Rudnev V, Totten GE (eds) Induction heating and heat treatment, ASM handbook Volume 4C. ASM International, Materials Park OH, pp 330–345
Yang BJ, Hattiangadi A, Li WZ, Zhou GF, McGreevy TE (2010) Simulation of steel microstructure evolution during induction heating. Mat Sci Eng A 527(12):2978–2984. https://doi.org/10.1016/j.msea.2010.01.038
Huang J, Poole WJ, Militzer M (2004) Austenite formation during intercritical annealing. Metall Mater Trans A 35a(11):3363–3375. https://doi.org/10.1007/s11661-004-0173-x
Savran VI (2009) Austenite formation in C-Mn steel. PhD thesis, Delft University of Technology,
Savran VI, Offerman SE, van Dijk NH, Lauridsen EM, Margulies L, Sietsma J (2007) Growth of individual austenite grains measured with 3DXRD microscopy. Pricm 6: Sixth Pacific Rim International Conference on Advanced Materials and Processing, Pts 1–3 561-565:2301-+. doi:10.4028/www.scientific.net/MSF.561-565.2301
Speich GR, Demarest VA, Miller RL (1981) Formation of austenite during intercritical annealing of dual-phase steels. Metall Mater Trans A 12(8):1419–1428. https://doi.org/10.1007/BF02643686
Azizi-Alizamini H, Militzer M, Poole WJ (2011) Austenite formation in plain low-carbon steels. Metall Mater Trans A 42(6):1544–1557. https://doi.org/10.1007/s11661-010-0551-5
Clarke KD, Van Tyne CJ, Vigil CJ, Hackenberg RE (2011) Induction hardening 5150 steel: effects of initial microstructure and heating rate. J Mater Eng Perform 20(2):161–168. https://doi.org/10.1007/s11665-010-9825-8
Molinder G (1956) A quantitative study of the formation of austenite and the solution of cementite at different austenitizing temperatures for a 1.27% carbon steel. Acta Metall 4(6):565–571
Katsamas AI (2007) A computational study of austenite formation kinetics in rapidly heated steels. Surf Coat Tech 201(14):6414–6422. https://doi.org/10.1016/j.surfcoat.2006.12.014
Savran VI, Van Leeuwen Y, Hanlon DN, Kwakernaak C, Sloof WG, Sietsma J (2007) Microstructural features of austenite formation in C35 and C45 alloys. Metall Mater Trans A 38a(5):946–955. https://doi.org/10.1007/s11661-007-9128-3
Dykhuizen RC, Robino CV, Knorovsky GA (1999) A method for extracting phase change kinetics from dilatation for multistep transformations: austenitization of a low carbon steel. Metall Mater Trans B Process Metall Mater Process Sci 30(1):107–117. https://doi.org/10.1007/s11663-999-0011-z
Jayaswal SK, Gupta SP (1992) Kinetics of ferrite to austenite transformation in a high-strength low-alloy steel containing Ti and V. Z Metallk 83(11):809–819
Puskar JDD, R. C, Robino CV, Burnett ME, Kelley JB (1999) Austeriite formation kinetics during rapid heating in a microalloyed steel. DOE's Office of Scientific and Technical Information (OSTI)
Schmidt E, Wang Y, Sridhar S (2006) A study of nonisothermal austenite formation and decomposition in Fe-C-Mn alloys. Metall Mater Trans A 37a(6):1799–1810. https://doi.org/10.1007/s11661-006-0122-y
de Andres CG, Caballero FG, Capdevila C (1998) Dilatometric characterization of pearlite dissolution in 0.1C-0.5Mn low carbon low manganese steel. Scripta Mater 38(12):1835–1842. https://doi.org/10.1016/S1359-6462(98)00131-6
Oliveira FLG, Andrade MS, Cota AB (2007) Kinetics of austenite formation during continuous heating in a low carbon steel. Mater Charact 58(3):256–261. https://doi.org/10.1016/j.matchar.2006.04.027
Speich GRS,A, Speich GR, Richards MJ (1969) Formation of austenite from ferrite and ferrite-carbide aggregates. Trans Metall Soc AIME 245:1063–1074
Li P, Li J, Meng QG, Hu WB, Xu DC (2013) Effect of heating rate on ferrite recrystallization and austenite formation of cold-roll dual phase steel. J Alloys Compd 578:320–327. https://doi.org/10.1016/j.jallcom.2013.05.226
Gaude-Fugarolas D Phase transformations in steel during induction hardening. In: Makhnenko VI (ed) Mathematical modelling and information technologies in welding and related processes. Katsiveli, Crimea, Ukraine, 16–20 September 2002. International Association «Welding»,
Ågren J (1982) Computer simulations of the austenite/ferrite diffusional transformations in low alloyed steels. Acta Metall 30(4):841–851. https://doi.org/10.1016/0001-6160(82)90082-7
Ågren J, Vassilev GP (1984) Computer simulations of cementite dissolution in austenite. Mat Sci Eng 64(1):95–103. https://doi.org/10.1016/0025-5416(84)90076-4
Atkinson C, Akbay T, Reed RC (1995) Theory for reaustenitisation from ferrite/cementite mixtures in Fe-C-X steels. Acta Metall Mater 43(5):2013–2031. https://doi.org/10.1016/0956-7151(94)00366-P
Wendel M, Hoffmann F, Datchary W (2016) Bearing steels for induction hardening—part I. J Heat Treat Mat 71(1):20–34. https://doi.org/10.3139/105.110277
Wendel M, Hoffmann F, Datchary W (2016) Bearing steels for induction hardening—part II. J Heat Treat Mat 71(5):218–229. https://doi.org/10.3139/105.110299
Lee SJ, Clarke KD (2010) A conversional model for austenite formation in hypereutectoid steels. Metall Mater Trans A 41a(12):3027–3031. https://doi.org/10.1007/s11661-010-0418-9
Caballero FG, Capdevila C, de Andres CG (2000) Influence of scale parameters of pearlite on the kinetics of anisothermal pearlite-to-austenite transformation in a eutectoid steel. Scripta Mater 42(12):1159–1165. https://doi.org/10.1016/S1359-6462(00)00352-3
Miyamoto G, Usuki H, Li ZD, Furuhara T (2010) Effects of Mn, Si and Cr addition on reverse transformation at 1073 K from spheroidized cementite structure in Fe-0.6 mass% C alloy. Acta Mater 58(13):4492–4502. https://doi.org/10.1016/j.actamat.2010.04.045
Chae JY, Jang JH, Zhang G, Kim KH, Lee JS, Bhadeshia HKDH, Suh DW (2011) Dilatometric analysis of cementite dissolution in hypereutectoid steels containing Cr. Scripta Mater 65(3):245–248. https://doi.org/10.1016/j.scriptamat.2011.04.018
Lee SJ, Clarke KD (2015) A quantitative investigation of cementite dissolution kinetics for continuous heating of hypereutectoid steel. Metall Mater Trans A 46a(9):3917–3923. https://doi.org/10.1007/s11661-015-2995-0
Zhao L, Vermolen FJ, Wauthier A, Sietsma J (2006) Cementite dissolution at 860 degrees C in an Fe-Cr-C steel. Metall Mater Trans A 37a (6):1841–1850. doi:DOI https://doi.org/10.1007/s11661-006-0127-6, 37
Lee S-J, Clarke KD (2010) A conversional model for austenite formation in hypereutectoid steels. Metall Mater Trans A 41(12):3027–3031. https://doi.org/10.1007/s11661-010-0418-9
Lee S-J, Clarke KD (2015) A quantitative investigation of cementite dissolution kinetics for continuous heating of hypereutectoid steel. Metall Mater Trans A 46(9):3917–3923. https://doi.org/10.1007/s11661-015-2995-0
Lai Q, Goune M, Perlade A, Pardoen T, Jacques P, Bouaziz O, Brechet Y (2016) Mechanism of austenite formation from spheroidized microstructure in an intermediate Fe-0.1C-3.5Mn steel. Metall Mater Trans A 47a(7):3375–3386. https://doi.org/10.1007/s11661-016-3547-y
Liu ZK, Hoglund L, Jonsson B, Agren J (1991) An experimental and theoretical-study of cementite dissolution in an Fe-Cr-C alloy. Metall Trans A 22(8):1745–1752. https://doi.org/10.1007/Bf02646498
Caballero FG, Capdevila C, De Andres CG (2003) An attempt to establish the variables that most directly influence the austenite formation process in steels. ISIJ Int 43(5):726–735. https://doi.org/10.2355/isijinternational.43.726
Mohanty RR, Girina OA, Fonstein NM (2011) Effect of heating rate on the austenite formation in low-carbon high-strength steels annealed in the intercritical region. Metall Mater Trans A 42a(12):3680–3690. https://doi.org/10.1007/s11661-011-0753-5
Caballero FG, Capdevila C, De Andres CG (2001) Influence of pearlite morphology and heating rate on the kinetics of continuously heated austenite formation in a eutectoid steel. Metall Mater Trans A 32(6):1283–1291. https://doi.org/10.1007/s11661-001-0218-3
Hernández-Morales BV-G,O, López-Martínez E, Vergara-Hernández HJ, Olmos L (2014) Effect of heating rate and silicon content on kinetics of austenite formation during continuous heating. Mater Sci Forum 783-786:771–776
Orlich JP,H-J (1976) Zeit-Temperatur-Austenitisierung-Schaubilder. In: Atlas zur Wärmebehandlung der Stähle, vol 4. Verlag Stahleisen, Düsseldorf, Germany
Orlich JR,A, Wiest P (1973) Zeit-Temperatur-Austenitisierung-Schaubilder. In: Atlas zur Wärmebehandlung der Stähle, vol 3. Verlag Stahleisen, Düsseldorf, Germany
Hayashi TKN, Yamada K. (2010) Method of prior austenite grain refining using induction hardening. JFE Steel Corporation
Vieweg A, Ressel G, Prevedel P, Marsoner S, Ebner R (2017) Effects of the inductive hardening process on the martensitic structure of a 50CrMo4 steel. J Heat Treat Mat 72(1):3–9. https://doi.org/10.3139/105.110308
Lesch C, Alvarez P, Bleck W, Sevillano JG (2007) Rapid transformation annealing: a novel method for grain refinement of cold-rolled low-carbon steels. Metall Mater Trans A 38a(9):1882–1890. https://doi.org/10.1007/s11661-006-9052-y
Rudnev V (2008) Metallurgical insights for induction heat treaters—part 5: super-hardening phenomenon. Heat Treating Prog:35–37
Prabhudev KH (1989) Handbook of heat treatment of steels. McGraw-Hill, USA
Fujita E, Ogura Y, Kawasaki S, Kojima S, Makita S, Maeda S, Yamane H, Yoshida S (2014) Manufacturing method of high-strength and high-toughness thin steel and heat treatment apparatus. U.S. Patent,
Rudnev V (2005) Be aware of the ‘fine print' in the science of metallurgy of induction hardening: part 1. Ind Heat March 2005:37–42
Rudnev V (2005) Be aware of the ‘fine print' in the science of metallurgy of induction hardening: part 2. Ind Heat May 2005:41–47
Morito S, Yoshida H, Maki T, Huang X (2006) Effect of block size on the strength of lath martensite in low carbon steels. Mat Sci Eng A 438:237–240. https://doi.org/10.1016/j.msea.2005.12.048
Tomita Y, Okabayashi K (1986) Effect of microstructure on strength and toughness of heat-treated low-alloy structural-steels. Metall Trans A 17(7):1203–1209. https://doi.org/10.1007/Bf02665319
Swarr T, Krauss G (1976) The effect of structure on the deformation of as-quenched and tempered martensite in an Fe-0.2 pct C alloy. Metall Trans A 7(1):41–48. https://doi.org/10.1007/BF02644037
Sackl S, Leitner H, Zuber M, Clemens H, Primig S (2014) Induction hardening vs conventional hardening of a heat treatable steel. Metall Mater Trans A 45a(12):5657–5666. https://doi.org/10.1007/s11661-014-2518-4
Morito S, Tanaka H, Konishi R, Furuhara T, Maki T (2003) The morphology and crystallography of lath martensite in Fe-C alloys. Acta Mater 51(6):1789–1799. https://doi.org/10.1016/S1359-6454(02)00577-3
Morito SI,R, Kamiya K, Ohba T, Maki T (2010) Effect of cooling rate on morphology and crystallography of lath martensite in Fe-Ni alloys. Mater Sci Forum 638-642:1459–1463
Jiang B, Dong ZQ, Zhou LY, Zhang CL, Liu YZ (2016) Microstructural characterization and hardening mechanism of steel for large size bearing ring under fast heating and short soaking time condition. Steel Res Int 87(9):1127–1136. https://doi.org/10.1002/srin.201500120
Morito S, Saito H, Ogawa T, Furuhara T, Maki T (2005) Effect of austenite grain size on the morphology and crystallography of lath martensite in low carbon steels. ISIJ Int 45(1):91–94. https://doi.org/10.2355/isijinternational.45.91
Zhang CY, Wang QF, Ren JX, Li RX, Wang MZ, Zhang FC, Sun KM (2012) Effect of martensitic morphology on mechanical properties of an as-quenched and tempered 25CrMo48V steel. Mat Sci Eng A 534:339–346. https://doi.org/10.1016/j.msea.2011.11.078
Krauss G (1999) Martensite in steel: strength and structure. Mat Sci Eng A 273:40–57. doi:Doi https://doi.org/10.1016/S0921-5093(99)00288-9
Kaijalainen AJ, Suikkanen PP, Limnell TJ, Karjalainen LP, Komi JI, Porter DA (2013) Effect of austenite grain structure on the strength and toughness of direct-quenched martensite. J Alloys Compd 577:S642–S648. https://doi.org/10.1016/j.jallcom.2012.03.030
Koistinen DPM, E R (1959) A general equation prescribing the extent of the austenite-martensite transformation in pure iron-carbon alloys and plain carbon steels. Acta Metall 7:59–60
Harris WHC,M (1949) Stabilization of the austenite-martensite transformation. Trans AIME 180:447–470
Speich GR, Leslie WC (1972) Tempering of steel. Metall Trans 3(5):1043–1054. https://doi.org/10.1007/BF02642436
Kristoffersen H, Vomacka P (2001) Influence of process parameters for induction hardening on residual stresses. Mater Des 22(8):637–644. https://doi.org/10.1016/S0261-3069(01)00033-4
Xu DH, Kuang ZB (1996) A study on the distribution of residual stress due to surface induction hardening. J Eng Mater-T Asme 118(4):571–575. https://doi.org/10.1115/1.2805958
Coupard D, Palin-Luc T, Bristiel P, Ji V, Dumas C (2008) Residual stresses in surface induction hardening of steels: comparison between experiment and simulation. Mat Sci Eng A 487(1–2):328–339. https://doi.org/10.1016/j.msea.2007.10.047
Savaria V, Monajati H, Bridier F, Bocher P (2015) Measurement and correction of residual stress gradients in aeronautical gears after various induction surface hardening treatments. J Mater Process Technol 220:113–123. https://doi.org/10.1016/j.jmatprotec.2014.12.009
Holmberg J, Steuwer A, Stormvinter A, Kristoffersen H, Haakanen M, Berglund J (2016) Residual stress state in an induction hardened steel bar determined by synchrotron- and neutron diffraction compared to results from lab-XRD. Mat Sci Eng A 667:199–207. https://doi.org/10.1016/j.msea.2016.04.075
Acknowledgements
The author gratefully acknowledges Dr. Valery Rudnev (FASM, “Professor Induction,” Science and Technology Director, Inductoheat, Inc), Michael Wendel (Process Specialist Heat Treatment, Group Manufacturing Development—MDC), Prof. Kester D. Clarke (Department of Metallurgical and Materials Engineering, Colorado School of Mines), and Prof. J. Zhang (College of Mechanical and Electrical Engineering, Hohai University) for supplying valuable papers on the subject. F. Coticelli is acknowledged for his invaluable editing support.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Prisco, U. Case microstructure in induction surface hardening of steels: an overview. Int J Adv Manuf Technol 98, 2619–2637 (2018). https://doi.org/10.1007/s00170-018-2412-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2412-0