Abstract
With advances in 3D printing technology, now honeycomb structures can be made with virtually unlimited unit cell geometries and cell arrangements giving a wide range of possible mechanical properties. However, studies on such structures have been mainly limited to the hexagonal honeycombs with little work done on other cell geometries. This paper investigates the effect of unit cell geometry on the in-plane compressive response and energy absorption behaviour of honeycombs using full-scale non-linear numerical simulations. Nine types of honeycombs are designed from different unit cell shapes, but having the same relative density. Finite element analysis is used to simulate the honeycombs’ behaviour under uniaxial compression loading. The results showed that unit cell geometry and cell arrangement affect the honeycombs’ compressive response significantly and provide different energy absorption characteristics. This comparison study shows that the honeycombs in which the deformation mode is dominated by bending of cell edges present a lower stiffness (effective modulus) and compressive strength, but a smoother plateau stress. The honeycombs having their deformation mode dominated by plastic buckling present a higher stiffness with less stable and undulated plateau stress. The results of this study provide more understanding in predicting the global behaviour of honeycomb structures and their energy absorption characteristic through their micro-topology. The effect of cell shape and its arrangement on the selection of honeycombs for energy absorption application is discussed and a methodology is proposed to balance the energy absorption with maximum transmitted stress, which is crucial for energy-absorbing design of structures.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gibson LJ, Ashby MF (1997) Cellular solids: structure and properties, second edn. Cambridge University Press, Cambridge, pp 1–510
Ashby MF (2006) The properties of foams and lattices. Philos Trans R Soc A Math Phys Eng Sci 364(1838):15–30
Srivastava V, Srivastava R (2014) On the polymeric foams: modeling and properties. J Mater Sci 49(7):2681–2692
Liu Y, Zhang X-C (2009) The influence of cell micro-topology on the in-plane dynamic crushing of honeycombs. Int J Impact Eng 36(1):98–109
Bates SRG, Farrow IR, Trask RS (2016) 3D printed polyurethane honeycombs for repeated tailored energy absorption. Mater Des 112:172–183
Habib FN et al (2017) In-plane energy absorption evaluation of 3D printed polymeric honeycombs. Virtual Phys Prototyp 12(2):117–131
Hedayati R et al (2016) Mechanical properties of additively manufactured thick honeycombs. Materials 9(8):613–636
Hedayati R et al (2016) Mechanical properties of additively manufactured octagonal honeycombs. Mater Sci Eng C 69:1307–1317
Papka SD, Kyriakides S (1994) In-plane compressive response and crushing of honeycomb. J Mech Phys Solids 42(10):1499–1532
Papka SD, Kyriakides S (1998) Experiments and full-scale numerical simulations of in-plane crushing of a honeycomb. Acta Mater 46(8):2765–2776
Ruan D et al (2003) In-plane dynamic crushing of honeycombs—a finite element study. Int J Impact Eng 28(2):161–182
Mozafari H et al (2015) In plane compressive response and crushing of foam filled aluminum honeycombs. J Compos Mater 49(26):3215–3228
Bates SRG, Farrow IR, Trask RS (2016) 3D printed elastic honeycombs with graded density for tailorable energy absorption. In: Park G (ed) Active and Passive Smart Structures and Integrated Systems Proc SPIE Vol. 9799, Las Vegas, United States
Wang A-J, McDowell D (2004) In-plane stiffness and yield strength of periodic metal honeycombs. J Eng Mater Technol 126(2):137–156
Papka SD, Kyriakides S (1998) In-plane crushing of a polycarbonate honeycomb. Int J Solids Struct 35(3):239–267
SYSTEMES D, Simulia, ABAQUS/CAE User's Manual (2014) ABAQUS Documentation V6 7
Standard, I., ISO 13314: 2011 (E) (2011) Mechanical testing of metals—ductility testing—compression test for porous and cellular metals. Ref Number ISO 13314(13314):1–7
Vesenjak M et al (2010) Cell shape effect evaluation of polyamide cellular structures. Polym Test 29(8):991–994
Lu G, Yu T (2003) In: Yu TX (ed) Energy absorption of structures and materials. Woodhead, Cambridge
Li QM, Magkiriadis I, Harrigan JJ (2006) Compressive strain at the onset of densification of cellular solids. J Cell Plast 42(5):371–392
Avalle M, Belingardi G, Montanini R (2001) Characterization of polymeric structural foams under compressive impact loading by means of energy-absorption diagram. Int J Impact Eng 25(5):455–472
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Habib, F.N., Iovenitti, P., Masood, S.H. et al. Cell geometry effect on in-plane energy absorption of periodic honeycomb structures. Int J Adv Manuf Technol 94, 2369–2380 (2018). https://doi.org/10.1007/s00170-017-1037-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-1037-z