Abstract
Machine tool dynamic characteristics are seriously affected by the changes of the machining poses and the spindle bearing joints dynamic properties. As these changes contribute much more complexity and uncertainty for predicting the machine tool dynamic characteristics accurately, a new method is developed to research the changing regularity of the whole machine tool dynamic characteristics in generalized manufacturing space. In this method, the dynamic flexibilities at the spindle nose of x, y, and z directions in the focused frequency range are taken to represent the whole machine tool dynamic characteristics. The response surface method (RSM) and the orthogonal experiment design method are combined to establish the generalized dynamic response model, which contains the information of the spatial poses and the spindle bearing dynamic parameters. To establish this model, the simulations arranged by the orthogonal design are conducted by utilizing the dynamic model modified approach based on the validated finite element model (FEM) of the whole machine tool. With evaluating the fitting degree of this generalized dynamic response model, it can be used to predict the dynamic characteristics in the manufacturing space. Furthermore, an algorithm based on the established model is proposed to calculate the effect factors acting on the whole machine tool dynamic characteristics, which are caused by the changes of the spindle bearing dynamic parameters. The proposed analytical method has been applied in a three-axis vertical machining center to establish its generalized dynamic response model. The dynamic flexibilities at the spindle nose in the generalized manufacturing space are predicted, and they are validated by the dynamic experiments. With the calibrated model, effect factors of the spindle bearing joints are also obtained. All the predicted results support a theoretical basis on the optimal process routes planning, and the proposed analytical method can lay a foundation for further study on the dynamic information of the tool point.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Lee SW, Mayor R, Ni J (2005) Dynamic analysis of a mesoscale machine tool. J Manuf Sci Eng 128(1):194–203
Liang YC, Chen WQ, Bai QS, Sun YZ, Chen GD, Zhang Q, Sun Y (2013) Design and dynamic optimization of an ultraprecision diamond flycutting machine tool for large KDP crystal machining. Int J Adv Manuf Technol 69:237–244
Wang YL, Wu XF, Feng HT(2012) Static and dynamic characteristics optimization for a whole large-sized thread grinder based on joint surface. Journal of Vibration and Shock 31(20):147–152
He SP, Mao XY, Liu XQ, Luo BO, Li B, Peng FY (2016) A new approach based on modal mass distribution matrix to identify weak components of machine tool structure. Int J Adv Manuf Technol 83(1):193–203
Park SS, Chae J (2008) Joint identification of modular tools using a novel receptance coupling method. Int J Adv Manuf Technol 35:1251–1262
Hung JP, Lai YL, Luo TZ (2013) Analysis of the machining stability of a milling machine considering the effect of machine frame structure and spindle bearings: experimental and finite element approaches. Int J Adv Manuf Technol 68:2393–2405
Kolar P, Sulitka M, Janota M (2011) Simulation of dynamic properties of a spindle and tools ystem coupled with a machine tool frame. Int J Adv Manuf Technol 54(1):11–20
Altintas Y, Brecher C, Weck M, Witt S (2005) Virtual machine tool. CIRP Keynote Paper 54(2):115–138
Zaeh M, Siedl D (2007) A new method for simulation of machining performance by integrating finite element and multi-body simulation for machine tools. CIRP Annals- Manufacturing Technology 56(1):383–386
Yang QD, Liu GQ, Wang KH (2008) Dynamics analysis of special structure of milling-head machine tool. Chinese Journal of Mechanical Engineering 21(6):103–107
Zhang GH, Ehmann KF (2015) Dynamic design methodology of high speed micro-spindles for micro/meso-scale machine tools. Int J Adv Manuf Technol 76(1):229–246
Wu J, Wang JS, Wang LP, Li T, You Z (2009) Study on the stiffness of a 5-DOF hybrid machine tool with actuation redundancy. Mech Mach Theory 44(2):289–305
Zaghbani I, Songmene V (2009) Estimation of machine-tool dynamic parameters during machining operation through operational modal analysis. Int J Mach Tools Manuf 49(12–13):947–957
Liu HT, Zhao WH (2010) Dynamic characteristic analysis for machine tools based on concept of generalized manufacturing space. Journal of Mechanical Engineering 46(21):54–60
Sun MN, Yin GF, Hu T, Hu XB (2013) Method of dynamic stiffness participation factors identification of machine tool joints based on the generalized dynamic information model. Journal of mechanical engineering 49(11):61–69
Li TJ, Ding XH, Cheng K (2015) Machine tool dynamics based on spatial statistics. Journal of mechanical engineering 51(21):87–94
Huang H, Zhang SY, Liu XJ, He ZX (2015) Research on cutting stability of generalized manufacturing space based on response surface mode. Journal of zhejiang university (engineering science) 49(7):1215–1223
Law M, Phani AS, Altintas Y (2013a) Position-dependent multibody dynamic modeling of machine tools based on improved reduced order models. Journal of Manufacturing Science & Engineering 135(2):2186–2199
Ding WZ, Huang XD, Wang ML, Zhu SQ (2013) An approach to evaluate the effects of nonlinear traveling joints on dynamic behavior of large machine tools. Int J Adv Manuf Technol 68(9):2025–2232
Chen K (2009) Machine tool design. Springer, London
Yan R, Chen W, Peng FY (2012) Closed-loop stiffness modeling and stiffness index analysis for multi-axis machining system. Journal of Mechanical Engineering 48(1):177–184
Wu WJ, Liu Q (2011) Dynamics analysis of aparallel mill-turn tool spindle head driven by dual-linear motors using extended transfer matrix method. Chinese Journal of Mechanical Engineering 24(5):859–869
Cao HG, Li B, He ZJ (2012) Chatter stability of milling with speed-varying of spindles. International Journal of Machine Tool & Manufacture 52(1):50–58
Zhang J, Schmitz T, Zhao WH, Lu BH (2013) Receptance coupling for tool point dynamics prediction on machine tools. Chinese Journal of Mechanical Engineering 24(3):340–345
Chen X, Zhao J, Zhang W (2016) Process optimization and typical application based on geometrical analysis and response surface method for high-speed five-axis ball-end milling operation. Int J Adv Manuf Technol. doi:10.1007/s00170-016-9143-x
Liu S (2015) Multi-objective optimization design method for the machine tool’s structural parts based on computer-aided engineering. Int J Adv Manuf Technol 78(5):1053–1065
Mi L, Yin GF, Sun MN (2012) Effects of preloads on joints on dynamic stiffness of a whole machine tool structure. J Mech Sci Technol 26:495–508
Jiang SY, Zhu SL (2010) Dynamic characteristic parameters of linear guideway joint with ball screw. Journal of mechanical engineering 4:92–99
Deng CY, Yin GF, Fang H, Meng ZYX (2015) Dynamic characteristics optimization for a whole vertical machining center based on the configuration of joint stiffness. Int J Adv Manuf Technol (2015) 76(5):1225–1242
Liao BY, Zhou XM, Yin ZH (2004) Modern mechanical dynamics and its application: modeling, analysis, simulation, modification, control, optimization. Beijing.
Zhang XL (2002) The dynamic characteristics of machine joint surface and its application. Beijing.
Huang YM (1985) The research of contact rigidity of machine tools slide ways and its influence factors. Journal of Xi'an University of Technology 3:16–25
Law M, Altintas Y, Srikanth A (2013b) Rapid evaluation and optimization of machine tools with position dependent stability. Int J Mach Tools Manuf 68(3):81–90
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Deng, C., Liu, Y., Zhao, J. et al. Analysis of the machine tool dynamic characteristics in manufacturing space based on the generalized dynamic response model. Int J Adv Manuf Technol 92, 1411–1424 (2017). https://doi.org/10.1007/s00170-017-0201-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0201-9