Abstract
EDM is a special type of non-traditional machining technique in which material removal takes place due to repeated electrical discharges at short intervals in the presence of a dielectric medium. It is used in high precision machining of all types of conductive materials such as metals, metallic alloys, graphite and even some ceramic materials. In EDM, the main output parameters are the material removal rate (MRR), electrode wear rate (EWR), and surface roughness (R a). It is generally desirable to obtain the maximum MRR with minimum EWR with good surface finish. The dielectrics play a vital role in machining. Even though EDM process has been traditionally used in die sinking industry mostly for machining hard materials, lighter materials like Ti alloy are machined more recently. In some cases, components made out of soft metals like Aluminium alloys are machined in EDM due to the intricacy of profiles, blind prismatic holes and inaccessible areas by other machining methods. This paper aims to investigate the effect of using different dielectrics, viz., biodiesel, transformer oil and kerosene on the material removal rate, electrode wear and surface roughness in EDM. Based on Taguchi’s design of experiments, machining were carried out on Aluminium Alloy 6063 specimens using a die-sinking EDM machine fitted with a copper electrode. The results show that the biodiesel as a dielectric has better performance in MRR, EWR and surface finish in comparison with kerosene and transformer oil. However, performance sustainability and the environmental effect of biodiesel have to be studied.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Kunieda M, Lauwers B, Rajurkar KP, Schumacher BM (2005) Advancing EDM through fundamental insight into the process. CIRP Annals-Manufacturing Technology 54(2):64–87
Krar SF, Check AF (1997) Electrical discharge machining, Technology of Machine Tools. Glencoe/McGraw-Hill, New York
Abbas NM, Solomon DG, Bahari Md F (2007) A review on current research trends in electrical discharge machining (EDM). Int J Mach Tools Manuf 47:1214–1228
Kiyak M, Cakir O (2007) Examination of machining parameters on surface roughness in EDM of tool steel. J Mater Process Technol 191:141–144
Zhang Y, Liu Y, Ji R, Cai B (2011) Study of the recast layer of a surface machined by sinking electrical discharge machining using water-in-oil emulsion as dielectric. Appl Surf Sci 257:5989–5997
Wong YS, Lim LC, Rahuman I, Tee WM (1998) Near-mirror-finish phenomenon in EDM using powder-mixed dielectric. J Mater Process Technol 79:30–40
Koenig W, Joerres L (1987) Aqueous solutions of organic compounds as dielectric for EDM sinking. CIRP Ann Manuf Technol 36:105–109
Chen SL, Yan BH, Huang FY (1999) Influence of kerosene and distilled water as dielectrics on the electric discharge machining characteristics of Ti–6Al–4V. J Mater Process Technol 87:107–111
Leao FN, Pashby IR (2004) A review on the use of environmentally friendly dielectric fluids in electrical discharge machining. J Mater Process Technol 149:341–346
Sivapirakasam SP, Mathew J, Surianarayanan M (2011) Constituent analysis of aerosol generated from die sinking electrical discharge machining process. Process Safe Environ Prot 89:141–150
Liu Y, Ji R, Zhang Y, Zhang H (2010) Investigation of emulsion for die sinking EDM. Int J Adv Manuf Technol 47:403–409
Kibria G, Sarkar BR, Pradhan BB, Bhattacharyya B (2010) Comparative study of different dielectrics for micro-EDM performance during micro hole machining of Ti-6Al-4 V alloy. Int J Adv Manuf Technol 48:557–570
Wei C, Zhao L, Hu D, Ni J (2013) Electrical discharge machining of ceramic matrix composites with ceramic fiber reinforcements. International Journal of Advance Manufacturing Technology 64:187–194
Tonshoff HK, Egger R, Klocke F (1996) Environmental and safety aspects of electro physical and electrochemical processes. CIRP Ann Manuf Technol 45:553–568
Tan XC, Liu F, Cao HJ, Zhang H (2002) A decision-making framework model of cutting fluid selection for green manufacturing and a case study. J Mater Process Technol 129:467–470
Kunieda M, Yoshida M, Taniguchi N (1997) Electrical discharge machining in gas. CIRP Ann Manuf Technol 46:143–146
Nguyen MD, Rahman M, Wong YS (2012) An experimental study on micro-EDM in low-resistivity deionized water using short voltage pulses. Int J Adv Manuf Technol 58:533–544
Altug M, Erdem M, Ozay C (2015) Experimental investigation of kerf of Ti6Al4V exposed to different heat treatment processes in WEDM and optimization of parameters using genetic algorithm. Int J Adv Manuf Technol 78:1573–1583
Singh H (2012) Experimental study of distribution of energy during EDM process for utilization in thermal models. Int J Heat Mass Transf 55:5053–5064
Zahiruddin M, Kunieda M (2012) Comparison of energy and removal efficiencies between micro and macro EDM. CIRP Ann Manuf Technol 61:187–190
Zhang Y, Liu Y, Ji R, Cai B, Shen Y (2013) Sinking EDM in water-in-oil emulsion. Int J Adv Manuf Technol 65:705–716
Ming QY, He LY (1995) Powder-suspension dielectric fluid for EDM. J Mater Process Technol 52:44–54
Pecas P, Henriques E (2008) Effect of the powder concentration and dielectric flow in the surface morphology in electrical discharge machining with powder-mixed dielectric (PMD-EDM). Int J Adv Manuf Technol 37:1120–1132
Khalid Hussain S, Kuppan P (2012) Performance of electrical discharge machining using aluminium powder suspended distilled water. Turkish J Eng Env Sci 36:195–207
Bhattacharya A, Batish A, Singh G, Singla VK (2012) Optimal parameter settings for rough and finish machining of die steels in powder-mixed EDM. Int J Adv Manuf Technol 61:537–548
Jiang Y, Zhao W, Xi X, Gu L, Kang X (2011) Detecting discharge status of small-hole EDM based on wavelet transform. Int J Adv Manuf Technol. doi:10.1007/s00170-011-3679-9
Jeswani ML (1981) Electrical discharge machining in distilled water. Wear 72:81–88
Tariq Jilani S, Pandey PC (1984) Experimental investigations into the performance of water as dielectric in EDM. Int J Mach Tool Des Res 24:31–43
Masuzawa T, Tanaka K, Nakamura Y (1983) Water-based dielectric solution for EDM. CIRP Ann Manuf Technol 32:119–122
Yan BH, Tsai HC, Huang FY (2005) The effect in EDM of a dielectric of a urea solution in water on modifying the surface of titanium. Int J Mach Tools Manuf 45:194–200
Tao J, Shih AJ, Jun N (2008) Experimental study of the dry and near dry electrical discharge milling processes. Journal of Manufacturing Science Engineering 130:1–9
Zhang QH, Zhang JH, Deng JX, Qin Y, Niu ZW (2002) Ultrasonic vibration electrical discharge machining in gas. J Mater Process Technol 129:135–138
Valaki JB, Rathod PP (2015) Assessment of operational feasibility of waste vegetable oil based bio dielectric fluid for sustainable electric discharge machining. Int J Adv Manuf Technol. doi:10.1007/s00170-015-7169-0
Pandey H, Dhakar K, Dvivedi A, Kumar P (2015) Parametric investigation and optimization of near-dry electrical discharge machining. Journal of Scientific & Industrial Research 74:508–511
Ji R, Liu Y, Zhang Y, Liu J, Li X (2011) Study on emulsion for electrical discharge milling of SiC ceramic. Adv Sci Lett 4(3):1214–1218
Liu YH, Ji RJ, Li XP, Yu LL, Zhang HF, Li QY (2008) Effect of machining fluid on the process performance of electric discharge milling of insulating Al2O3 ceramic. International Journal of Machine Tools & Manufacture 48:1030–1035
Choudhary SK, Jadoun RS (2014) Current advanced research and development of electric discharge machining (EDM): a review. International Journal of Research in Advent Technology 2:273–297
Kiyak M, Bilal EA, Erhan A (2015) Effects of discharge energy density on wear rate and surface roughness in EDM. Int J Adv Manuf Technol. doi:10.1007/s00170-015-6840-9
Wang X, Zhidong L, Rongyuan X, Zongjun T, Yinhui H (2014) Research on the influence of dielectric characteristics on EDM of titanium alloy. Int J Adv Manuf Technol. doi:10.1007/s00170-014-5716-8
Ji R, Liu Y, Zhang Y, Cai B, Ma J, Li X (2012) Influence of dielectric and machining parameters on the process performance for electric discharge milling of SiC ceramic. Int J Adv Manuf Technol 59:127–136. doi:10.1007/s00170-011-3493-1
Liu Y, Ji R, Zhang Y, Zhang H (2010) Investigation of emulsion for die sinking EDM. Int J Adv Manuf Technol 47:403–409. doi:10.1007/s00170-009-2209-2
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
P., S., B., M. Investigation on the influence of different types of dielectrics in electrical discharge machining. Int J Adv Manuf Technol 92, 277–291 (2017). https://doi.org/10.1007/s00170-017-0039-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0039-1