Abstract
The prediction of the deviation of bending point in asymmetric V-die bending is extremely needed for practical application. An analytical model and a series of experiments are performed to characterize high strength steel (HSS) sheet metal parts fabricated by asymmetric V-die bending dies and trapezoid sheet. The proposed strategy uses an elementary bending theory to develop a basic model to predict the position deviation of bending point of asymmetric V-die bending process and to test its viability for a trapezoid sheet. Accordingly, a series of experiments obtained good agreement with the calculations. The effects of die radius on deviation in the bending point were experimentally tested to identify the behavior of position deviation in sheet metal bending processes. The experimental results show the important role of contact friction on deviation change; however, its value, i.e., friction coefficient, is always difficult to be determined in calculation. In conclusion, the interactive effects of process parameters are complex and show the important roles of die radius and sheet width on deviation change. The results of this study can be considered when developing process design guidelines for asymmetric processes in HSS sheets.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bakhshi-Jooybari M, Rahmani B, Daeezadeh V, Gorji A (2009) The study of spring-back of CK67 steel sheet in V-die and U-die bending processes. Mater Des 30(7):2410–2419
Narayanasamy R, Padmanabhan P (2009) Application of response surface methodology for predicting bend force during air bending process in interstitial free steel sheet. Int J Adv Manuf Technol 44:38–48
Farsi MA, Arezoo B (2009) Development of a new method to determine bending sequence in progressive dies. Int J Adv Manuf Technol 43:52–60
Yu HY (2009) Variation of elastic modulus during plastic deformation and its influence on springback. Mater Des 30:846–850
Ramezani M, Mohd Ripin Z, Ahmad R (2010) Modelling of kinetic friction in V-bending of ultra-high-strength steel sheets. Int J Adv Manuf Technol 46:101–110
Ramezani M, Mohd Ripin Z (2010) A friction model for dry contacts during metal-forming processes. Int J AdvManuf Technol 51:93–102
Fu Z, Mo J (2010) Multiple-step incremental air-bending forming of high-strength sheet metal based on simulation analysis. Mater Manuf Process 25(8):808–816
Ozturk F, Ece RE, Polat N, Koksal A (2010) Effect of warm temperature on springback compensation of titanium sheet. Mater Manuf Process 23(9):1021–1024
Fu Z, Mo J (2011) Springback prediction of high-strength sheet metal under air bending forming and tool design based on GA–BPNN. Int J Adv Manuf Technol 53(5–8):473–483
Chatti S, Hermi N (2011) The effect of non-linear recovery on springback prediction. Comput Struct 89(13–14):1367–1377
Baseri H, Bakhshi-Jooybari M, Rahmani B (2011) Modeling of spring-back in V-die bending process by using fuzzy learning back-propagation algorithm. Expert Syst Appl 38(7):8894–8900
Kardes Sever N, Mete OH, Demiralp Y, Choi C, Altan T (2012) Springback prediction in bending of AHSS-DP 780. Proc NAMRI/SME 40:1–10
Fu ZM (2012) Numerical simulation of springback in air-bending forming of sheet metal. Appl Mech Mater 121–126:3602–3606
Malikov V, Ossenbrink R, Viehweger B, Michailov V (2012) Experimental investigation and analytical calculation of the bending force for air bending of structured sheet metals. Adv Mater Res 418–420:1294–1300
Duc-Toan N, Seung-Han Y, Dong-Won J, Tien-Long B, Young-Suk K (2012) A study on material modeling to predict spring-back in Vbending of AZ31 magnesium alloy sheet at various temperatures. Int J Adv Manuf Technol 62:551–562
Lee JY, Lee JW, Lee MG, Barlat F (2012) An application of homogeneous anisotropic hardening to springback prediction in pre-strained U-draw/bending. Int J Solids Struct 49(25):3562–3572
Song Y, Yu Z (2013) Springback prediction in T-section beam bending process using neural networks and finite element method. Archives of Civil and Mechanical Engineering 13(2):229–241
Parsa MH, Mohammadi SV (2014) Al3105/polypropylene/Al3105 laminates springback in V-die bending. Int J Adv Manuf Technol 75(5):849–860
Zong YY, Liu P, Guo B, Shan DB (2015) Springback evaluation in hot v-bending of Ti-6Al-4V alloy sheets. Int J Adv Manuf Technol 76(1):577–585
Fang Z, Jiang ZY, Wei DB (2015) Study on springback in micro V-bending with consideration of grain heterogeneity. Int J Adv Manuf Technol 78(5):1075–1085
Leu DK (2013) Position deviation in V-die bending process with asymmetric bend length. Int J Adv Manuf Technol 64:93–103
Leu DK (2015) Position deviation of bending point in V-die bending process with asymmetric dies. Int J Adv Manuf Technol 79:1095–1108
Leu DK (1997) A simplified approach for evaluation bendability and springback in plastic bending of anisotropic sheet metals. J Mater Process Technol 66:9–17
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Leu, DK. Position deviation of bending point in asymmetric V-die bending process with HSS trapezoid sheet. Int J Adv Manuf Technol 91, 3727–3735 (2017). https://doi.org/10.1007/s00170-017-0029-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0029-3