Abstract
2060 Al–Cu–Li alloy plates with 2- and 1-mm thickness were welded by a fiber laser beam. The weld microstructure features and the mechanical properties such as microhardness and tensile strength of 2060 Al–Cu–Li alloy laser beam-welded joint were investigated to study the influence of welding parameters on the weld bead. By microstructure and mechanical property analysis, it is found that weld width as well as penetration depth increases with the increase of laser power when the welding speed is constant. The microstructures of the fusion line and fusion zone show similar dendrite morphologies with traditional cast structure under the thermal cycling. Fine grain zone can be observed near the fusion line. Welding porosities exist in the microstructure of 2060 Al–Cu–Li laser beam-welded joint. Porosity ratio increases at first, and then declines, and then increases again with the increase of laser power. The larger heat input causes the lower microhardness distribution of the corresponding joint. The optimized welding parameters of fiber laser beam welding of 2- and 1-mm-thick 2060 Al–Cu–Li alloys are 2500 W and 3 m/min and 2300 W and 4 m/min, respectively.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Schubert E, Klassen M, Zerner I, Walz C, Sepold G (2001) Light-weight structures produced by laser beam joining for future applications in automobile and aerospace industry. J Mater Process Technol 115(1):2–8
Haboudou A, Peyre P, Vannes AB, Peix G (2003) Reduction of porosity content generated during Nd:YAG laser welding of A356 and AA5083 aluminium alloys. Mater Sci Eng A 363(1–2):40–52
Wang X, Wang H, Lu F, Carlson BE, Wu Y (2014) Analysis of solidification cracking susceptibility in side-by-side dual-beam laser welding of aluminum alloys. Int J Adv Manuf Technol 73(1–4):73–85
İpekoğlu G, Erim S, Çam G (2014) Effects of temper condition and post weld heat treatment on the microstructure and mechanical properties of friction stir butt-welded AA7075 Al alloy plates. Int J Adv Manuf Technol 70(1–4):201–213
Casalino G, Mortello M (2016) Modeling and experimental analysis of fiber laser offset welding of Al-Ti butt joints. Int J Adv Manuf Technol 83(1–4):89–98
Wang Q, Chen H, Zhu Z, Qiu P, Cui Y (2016) A characterization of microstructure and mechanical properties of A6N01S-T5 aluminum alloy hybrid fiber laser-MIG welded joint. Int J Adv Manuf Technol. doi:10.1007/s00170-015-8280-y
Ancona A, Lugarà PM, Sorgente D, Tricarico L (2007) Mechanical characterization of CO2 laser beam butt welds of AA5083. J Mater Process Technol 191(1–3):381–384
Yang ZB, Tao W, Li LQ, Chen YB, Li FZ, Zhang YL (2012) Double-sided laser beam welded T-joints for aluminum aircraft fuselage panels: process, microstructure, and mechanical properties. Mater Des 33:652–658
Gao M, Chen C, Mei S, Wang L, Zeng X (2014) Parameter optimization and mechanism of laser–arc hybrid welding of dissimilar Al alloy and stainless steel. Int J Adv Manuf Technol 74(1–4):199–208
Dursun T, Soutis C (2014) Recent developments in advanced aircraft aluminium alloys. Mater Des 56:862–871
Molian PA, Srivatsan TS (1990) Weldability of aluminium-lithium alloy 2090 using laser welding. J Mater Sci 25:3347–3358
Hou KH, Baeslack WAI (1996) Effect of solute segregation on the weld fusion zone microstructure in CO2 laser beam and gas tungsten arc welds in Al-Li-Cu alloy 2195. J Mater Sci Lett 15(3):208–213
Shi Y, Zhong F, Li X, Gong S, Chen L (2007) Effect of laser beam welding on tear toughness of a 1420 aluminum alloy thin sheet. Mater Sci Eng A 465(1–2):153–159
Fu B, Qin G, Meng X, Ji Y, Zou Y, Lei Z (2014) Microstructure and mechanical properties of newly developed aluminum–lithium alloy 2A97 welded by fiber laser. Mater Sci Eng A 617:1–11
Yan J, Gao M, Li G, Zhang C, Zeng X, Jiang M (2013) Microstructure and mechanical properties of laser-MIG hybrid welding of 1420 Al-Li alloy. Int J Adv Manuf Technol 66(9–12):1467–1473
Karabin LM, Bray GH, Rioja RJ, Venema G, (2012) Al-Li-Cu-Mg-(Ag) Products for lower wing skin applications. Proceedings of the 13th international conference on aluminum alloys (ICAA13). 529–534
Zhang X, Yang W, Xiao R (2015) Microstructure and mechanical properties of laser beam welded Al–Li alloy 2060 with Al–Mg filler wire. Mater Des 88:446–450
Zhan X, Wang Y, Liu Y, Zhang Q, Li Y, Wei Y (2015) Investigation on parameter optimization for laser welded butt joint of TA15 alloy. Int J Adv Manuf Technol. doi:10.1007/s00170-015-7900-x
Li G, Gao M, Chen C, Zhang C, Zeng XY (2014) Characterisation comparison of laser and laser–arc hybrid welding of Invar 36 alloy. Sci Technol Weld Join 19(1):30–37
Zhang MJ, Chen GY, Zhang Y, Wu KR (2013) Research on microstructure and mechanical properties of laser keyhole welding–brazing of automotive galvanized steel to aluminum alloy. Mater Des 45:24–30
Kong JP, Park TJ, Kim JK, Uhm SH, Woo IS, Lee JS, Park BG et al (2011) Characterization of laser welds in Al–10wt.% Si coated ferritic stainless steel. Mater Des 32(2):917–925
Pang S, Chen W, Wang W (2014) A quantitative model of keyhole instability induced porosity in laser welding of titanium alloy. Metall Mater Trans A 45(6):2808–2818
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gu, C., Wei, Y., Zhan, X. et al. Investigation of welding parameters on microstructure and mechanical properties of laser beam-welded joint of 2060 Al–Cu–Li alloy. Int J Adv Manuf Technol 91, 771–780 (2017). https://doi.org/10.1007/s00170-016-9806-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9806-7