Abstract
Rubber profile manufacturers have strong incentives to optimize the design of their extrusion dies and reduce the longer development times. Computational fluid dynamics (CFD) modeling is today the most effective alternative to traditional methods for adjusting die geometry and extrusion parameters. However, in practical terms, CFD modeling is often hindered by particular features of the extrusion process such as the lack of a single constitutive equation for all types of rubber flow. This article proposes a practical methodology based on simulation results and experimental data from an easy-to-build 4-channel die to help in the selection of the most adequate constitutive model of a rubber blend. The methodology was validated in a particular ethylene-propylene-diene monomer (EPDM). Characterization experiments were first carried out to obtain three constitutive models: Herschel-Bulkley, Bird-Carreau, and power law. Then, the EPDM was extruded in the manufactured die, and the total rubber that passes through the 4-channel die together with the inlet pressure was measured. CFD simulations of the 4-channel die were lastly analyzed. In our case study, the Bird-Carreu model, experimentally obtained by dynamic mechanical analysis, turned out to be the best candidate model for the EPDM studied. Subsequently, we demonstrated that a valid constitutive equation can be effectively selected by applying the methodology proposed with relatively low cost.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Cho JR, Choi JH (2016) Numerical investigation of weather strip extrusion forming process by thermal flow analysis. Int J Adv Manuf Technol :1–11
Marcos González A, Pernía Espinoza AV, Alba Elías F et al (2007) A neural network-based approach for optimising rubber extrusion lines. Int J Comput Integr Manuf 20(8):828–837
Li Y, Yang H, Xing Z (2016) Numerical simulation and process optimization of squeeze casting process of an automobile control arm. Int J Adv Manuf Technol :1–7
Milivoje MK, Louis GR (2007) Design of extrusion dies. In: Encyclopedia of Chemical Processing, vol null. vol null. Taylor & Francis, pp 633–649
Gonçalves ND, Carneiro OS, Nóbrega JM (2013) Design of complex profile extrusion dies through numerical modeling. J Non-Newtonian Fluid Mech 200(0):103–110
Singhry HB, Abd Rahman A, Imm NS (2015) Effect of advanced manufacturing technology, concurrent engineering of product design, and supply chain performance of manufacturing companies. Int J Adv Manuf Technol :1–7
Cox WP, Merz EH (1958) Correlation of dynamic and steady flow viscosities. J Polym Sci 28(118):619–622
Liu P, Shuisheng X, Cheng L (2012) Die structure optimization of large, multi-cavity aluminum profile using numerical simulation and experiments. Mater Des 36:152–160
Martínez de Pisón FJ, Barreto C, Pernía Espinoza AV et al (2008) Modelling of an elastomer profile extrusion process using support vector machines (SVM). J Mater Process Technol 197(1–3):161–169
Elgeti S, Probst M, Windeck C et al (2012) Numerical shape optimization as an approach to extrusion die design. Finite Elem Anal Des 61(0):35–43
Michaeli W (1992) Extrusion dies for plastic and rubber: design and engineering computations, 2nd edn. Hanser Gardner Publications, Munich
Mu Y, Zhao G, Chen A et al (2013) Modeling and simulation of polymer melts flow in the extrusion process of plastic profile with metal insert. Int J Adv Manuf Technol 67(1):629–646
Mu Y, Zhao G, Wu X et al (2010) An optimization strategy for die design in the low-density polyethylene annular extrusion process based on FES/BPNN/NSGA-II. Int J Adv Manuf Technol 50(5):517–532
Barreto Cabrera C, Ordieres Meré J, Castejón Limas M et al (2010) A data-driven manufacturing support system for rubber extrusion dies. Int J Prod Res 48(8):1–13
Dafermus C, Ericksen JL, Kinderlehrer D (1987) Amorphous polymers and non-Newtonian fluids. Springer, New York, NY
Siegbert R, Yesildag N, Frings M et al (2015) Individualized production in die-based manufacturing processes using numerical optimization. Int J Adv Manuf Technol 80(5):851–858
Ostwald W (1925) Concerning the function rate of the viscosity of dispersion systems. Kolloid Zeitschrift 36:248–150
Liang JZ (1996) A study of the die-swell behaviour of rubber compounds during short-die extrusion. J Mater Process Technol 59(3):268–271
Sienz J, Goublomme A, Luege M (2010) Sensitivity analysis for the design of profile extrusion dies. Comput Struct 88(9–10):610–624
Meeten GH (2002) Constant-force squeeze flow of soft solids. Rheol Acta 41:557–566
Zienkiewicz OC, Taylor RL, Zhu JC (2005) The finite element method for fluid dynamics, 6th edn. Butterworth-Heinemann, Oxford
del Coz Díaz JJ, García Nieto PJ, Bello García A et al (2008) Finite volume modeling of the non-isothermal flow of a non-Newtonian fluid in a rubber’s extrusion die. J Non-Cryst Solids 354(47–51):5334–5336
del Coz Díaz JJ, García Nieto PJ, Ordieres Meré J et al (2007) Computer simulation of the laminar nozzle flow of a non-Newtonian fluid in a rubber extrusion process by the finite volume method and experimental comparison. J Non-Cryst Solids 353(8–10):981–983
Vaddiraju SR, Kostic M, Reifschneider L et al. (2004) Extrusion simulation and experimental validation to optimize precision design dies. In: ANTEC 2004-Annual Technical Conference Proceedings, Chicago, IL. Society of Plastics Engineers, pp 76–80
Carneiro OS, Nóbrega JM, Pinho FT et al (2001) Computer aided rheological design of extrusion dies for profiles. J Mater Process Technol 114(1):75–86
Ha YS, Cho JR, Kim TH et al (2008) Finite element analysis of rubber extrusion forming process for automobile weather strip. J Mater Process Technol 201(1–3):168–173
Ganvir V, Lele A, Thaokar R et al (2009) Prediction of extrudate swell in polymer melt extrusion using an Arbitrary Lagrangian Eulerian (ALE) based finite element method. J Non-Newtonian Fluid Mech 156(1–2):21–28
Mitsoulis E, Georgiou GC, Kountouriotis Z (2012) A study of various factors affecting Newtonian extrudate swell. Comput Fluids 57(0):195–207
Edwards KL (1998) A designers’ guide to engineering polymer technology. Mater Des 19:57–67
Mompean G, Thais L, Tomé MF et al (2011) Numerical prediction of three-dimensional time-dependent viscoelastic extrudate swell using differential and algebraic models. Comput Fluids 44(1):68–78
Pauli L, Behr M, Elgeti S (2013) Towards shape optimization of profile extrusion dies with respect to homogeneous die swell. J Non-Newtonian Fluid Mech 200(0):79–87
Al-Muslimawi A, Tamaddon-Jahromi HR, Webster MF (2013) Simulation of viscoelastic and viscoelastoplastic die-swell flows. J Non-Newtonian Fluid Mech 191(0):45–56
Müllner HW, Eberhardsteiner J, Mackenzie-Helnwein P (2009) Constitutive characterization of rubber blends by means of capillary-viscometry. Polym Test 28(1):13–23
Müllner HW, Wieczorek A, Eberhardsteiner J (2011) Experimental determination of shear-thinning behaviour during extrusion of rubber blends. Strain 47(2):167–172
ANSYS I (2011) ANSYS POLYFLOW User’s Guide, 14th edn. ANSYS, Inc, Canonsburg, PA
Versteeg H, Malalasekera W (2007) An introduction to computational fluid dynamics: the finite volume method, 2nd edn. Pretince Hall
Cengel YA, Cimbala JM (2006) Fluid mechanics: fundamentals and applications, 2nd edn. McGraw-Hill, New York, NY
ANSYS I (2011) ANSYS Meshing user’s guide, 14th edn. ANSYS, Inc, Canonsburg, PA
del Coz Díaz JJ, García Nieto PJ, Suarez Sierra JL et al (2013) Nonlinear thermal optimization of external light concrete mulit-holded brick walls by the finite element method. Int J Heat Mass Transf 51:1530–1541
Chhabra RP (2010) Non-Newtonian fluid: an introduction. In: Deshpande AP, Krishnan JM, Kumar S (eds) Rheology of complex fluids. Springer, New York, NY
Zhu H, Kim YD, De Kee D (2005) Non-Newtonian fluids with a yield stress. J Non-Newtonian Fluid Mech 129(3):177–181
Smyrnaios DN, Tsamopoulos JA (2001) Squeeze flow of Bingham plastics. J Non-Newtonian Fluid Mech 100:165–190
Jones DS (1999) Dynamic mechanical analysis of polymeric systems of pharmaceutical and biomedical significance. Int J Pharm 179(2):167–178
Author information
Authors and Affiliations
Corresponding author
Electronic supplementary material
Figure S1
Velocity contour plots obtained from the CFD simulation results using (a) Herschel-Bulkley curve, (b) power law and (c) Bird-Carreau equation. (JPEG 498 kb)
Rights and permissions
About this article
Cite this article
Urraca, R., Pernía-Espinoza, A., Díaz, I. et al. Practical methodology for validating constitutive models for the simulation of rubber compounds in extrusion processes. Int J Adv Manuf Technol 90, 2377–2387 (2017). https://doi.org/10.1007/s00170-016-9537-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9537-9