Abstract
Powder injection-molding (PIM) simulations are useful to identify appropriate combinations of material, process, and geometry variables required for successful manufacturing outcomes. PIM simulations can identify optimized processing parameters without the requirement of expensive trials when changes are made to feedstock composition or geometry design. However, PIM simulations require physical, thermal, and rheological feedstock properties as input data that require additional time, expertise, and expense. Whereas injection-molding simulation platforms typically offer over 5000 listings of property datasets for polymers, there are presently fewer than 5 such listings for ceramics and metals. The present work compares experimentally measured physical, thermal, and rheological properties for an aluminum nitride (AlN) feedstock to estimated values based on known filler properties and semi-empirical models. Injection-molding experimental studies carried out on a simple test geometry showed reasonable correspondence to PIM simulations using the two datasets. Further, mold-filling simulations were performed on complex heat-sink substrate geometries to compare the output of PIM simulations using experimentally measured and estimated feedstock property datasets. The present study indicates the merit of using estimated feedstock properties as input parameters in mold-filling simulations that could be extended for a variety of material systems and geometries early in the PIM design stage.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
German RM, Atre SV (2013) PIM 2013 market study. New York
Atre SV, Park S-J, Zauner R, German RM (2007) Process simulation of powder injection moulding: identification of significant parameters during mould filling phase. Powder Metall 50:76–85. doi:10.1179/174329007X185607
Urval R, Lee S, Atre SV et al (2008) Optimisation of process conditions in powder injection moulding of microsystem components using a robust design method: part I. primary design parameters. Powder Metall 51:133–142. doi:10.1179/174329008X284796
Kate KH, Onbattuvelli VP, Enneti RK et al (2012) Measurements of powder–polymer mixture properties and their use in powder injection molding simulations for aluminum nitride. JOM 64:1048–1058. doi:10.1007/s11837-012-0404-3
Ahn S, Chung ST, Atre SV et al (2008) Integrated filling, packing and cooling CAE analysis of powder injection moulding parts. Powder Metall 51:318–326. doi:10.1179/174329008X284903
Park S-J, Ahn S, Kang TG et al (2010) A review on computer simulations in powder injection molding. Int J Powder Metall 46:37–46
Onbattuvelli VP, Enneti RK, Park S-J, Atre SV (2013) The effects of nanoparticle addition on SiC and AlN powder–polymer mixtures: packing and flow behavior. Int J Refract Met Hard Mater 36:183–190. doi:10.1016/j.ijrmhm.2012.08.014
Onbattuvelli VP (2010) The effects of nanoparticle addition on the processing, structure and properties of SiC and AlN
Groza JR, Zavaliangos A (2000) Sintering activation by external electrical field. Mater Sci Eng A 287:171–177. doi:10.1016/S0921-5093(00)00771-1
Biswas K, Schneider J, Rixecker G, Aldinger F (2005) Comparative bending creep behaviour of silicon carbide sintered with oxynitride additives. Scr Mater 53:591–596. doi:10.1016/j.scriptamat.2005.04.024
Gu J, Zhang Q, Dang J et al (2009) Thermal conductivity and mechanical properties of aluminum nitride filled linear low-density polyethylene composites. Polym Eng Sci 49:1030–1034. doi:10.1002/pen.21336
Kochetov R, Andritsch T, Lafont U et al (2009) Preparation and dielectric properties of epoxy - BN and epoxy - AlN nanocomposites. In: IEEE Electr Insul Conf 2009 EIC 2009 pp 397–400
Zhou W (2011) Thermal and dielectric properties of the AlN particles reinforced linear low-density polyethylene composites. Thermochim Acta 512:183–188. doi:10.1016/j.tca.2010.10.003
Zhu BL, Ma J, Wu J et al (2010) Study on the properties of the epoxy-matrix composites filled with thermally conductive AlN and BN ceramic particles. J Appl Polym Sci 118:2754–2764. doi:10.1002/app.32673
Risbud SH, Groza JR, Kim MJ (1994) Clean grain boundaries in aluminium nitride ceramics densified without additives by a plasma-activated sintering process. Philos Mag Part B 69:525–533. doi:10.1080/01418639408240126
Khor KA, Cheng KH, Yu LG, Boey F (2003) Thermal conductivity and dielectric constant of spark plasma sintered aluminum nitride. Mater Sci Eng A 347:300–305. doi:10.1016/S0921-5093(02)00601-9
Medraj M Understanding AlN sintering through computational thermodynamics combined with experimental investigation. J Mater Process Tech 161:415–422
Qiao L, Zhou H, Fu R (2003) Thermal conductivity of AlN ceramics sintered with CaF2 and YF3. Ceram Int 29:893–896. doi:10.1016/S0272-8842(03)00033-6
Miyashiro F, Iwase N, Tsuge A et al (1990) High thermal conductivity aluminum nitride ceramic substrates and packages. IEEE Trans Compon Hybrids Manuf Technol 13:313–319. doi:10.1109/33.56163
Cardarelli F (2008) Materials handbook: a concise desktop reference. Springer Science & Business Media
Bae J-W, Kim W, Cho S-H, Lee S-H (2000) The properties of AlN-filled epoxy molding compounds by the effects of filler size distribution. J Mater Sci 35:5907–5913. doi:10.1023/A:1026741300020
Bauccio M (1994) ASM engineered materials reference book. ASM International
Granta’s CES EduPack and teaching resources: supporting Materials Education. http://www.grantadesign.com/education/. Accessed 27 Sep 2013
Jackson TB, Virkar AV, More KL et al (1997) High-thermal-conductivity aluminum nitride ceramics: the effect of thermodynamic, kinetic, and microstructural factors. J Am Ceram Soc 80:1421–1435. doi:10.1111/j.1151-2916.1997.tb03000.x
Slack GA (1964) Thermal conductivity of pure and impure silicon, silicon carbide, and diamond. J Appl Phys 35:3460. doi:10.1063/1.1713251
YimWM, Paff RJ (1974) Thermal expansion of AlN, sapphire, and silicon. J Appl Phys 45:1456. doi:10.1063/1.1663432
Qiao L, Zhou H, Xue H, Wang S (2003) Effect of Y2O3 on low temperature sintering and thermal conductivity of AlN ceramics. J Eur Ceram Soc 23:61–67. doi:10.1016/S0955-2219(02)00079-1
Qiao L, Zhou H, Chen K, Fu R (2003) Effects of Li2O on the low temperature sintering and thermal conductivity of AlN ceramics. J Eur Ceram Soc 23:1517–1524. doi:10.1016/S0955-2219(02)00344-8
Kate KH, Enneti RK, Park S-J et al (2014) Predicting powderpolymer mixture properties for PIM design. Crit Rev Solid State Mater Sci 39:197–214. doi:10.1080/10408436.2013.808986
Ashby MF (2010) Materials selection in mechanical design. Butterworth-Heinemann
HaynesWM(2014) CRC handbook of chemistry and physics, 95th edition. CRC Press
Center PUTPR (1970) Thermophysical properties ofmatter: specific heat: metallic elements and alloys, by Y. S. Touloukian and E. H. Buyco. IFI/Plenum
Nakano H, Watari K, Hayashi H, Urabe K (2002) Microstructural characterization of high-thermal-conductivity aluminum nitride ceramic. J Am Ceram Soc 85:3093–3095. doi:10.1111/j.1151-2916.2002.tb00587.x
Smothers WJ (2009) 1981 New England section topical meeting on nonoxide ceramics: ceramic engineering and science proceedings, volume 3, number 1/2. John Wiley & Sons
Shoemaker J (2006) Moldflow design guide: ’a resource for plastics engineers. Hanser Publications, Munich
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kate, K.H., Enneti, R.K. & Atre, S.V. Influence of feedstock properties on the injection molding of aluminum nitride. Int J Adv Manuf Technol 90, 2813–2826 (2017). https://doi.org/10.1007/s00170-016-9530-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9530-3