Abstract
This work reports the performance evaluation of low-cost hot embossing processes of fine three-dimensional microstructures, namely (i) cylindrical microlens array, (ii) plano-convex aspheric Fresnel lens, and (iii) pyramidal array structures. All those optical elements were replicated by employing a low-cost hot embossing tool in optical quality acrylic material. Scanning electron microscopy and optical interference microscopy techniques were used to quantitatively measure the obtained structures. In terms of the replication fidelity with respect to the mold counterpart, the resulting optical elements presented at least 96 % of dimensional fidelity at micro- and nanometer scale, including the structures with sharp edges present in the Fresnel lens. In terms of the surface optical quality, resulting root mean square surface roughness of at least one tenth of wavelength was obtained, considering applications in the visible range of spectrum. The results showed that even nanostructures generated by the material removal mechanisms during mold fabrication, such as crystal grain elastic recovery, were well replicated with differences in the range of few of nanometers which is within the vertical resolution of the employed optical interference technique.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Herzig HP (1997) Micro-optics: elements, systems and applications. Taylor and Francis, Bristol, p 61
Hung KY, Chen YK, Huang SH, Shye DC (2010) Molding and hot forming techniques for fabricating plastic aspheric lenses with high blue-light transmittance. Microsyst Technol 16:1439–1444
Su Y, Shah J, Liwei L (2004) Implementation and analysis of polymeric microstructure replication by micro injection molding. J Micromech Microeng 14:415–422
Metwally K, Barriere T, Khan-Malek C (2016) Replication of micrometric and sub-micrometric structured surfaces using micro-injection and micro-injection compression moulding. Int J Adv Manuf Technol 83:779–789
Mosaddegh P, Angstadt DC (2008) Micron and sub-micron feature replication of amorphous polymers at elevated mold temperature without externally applied pressure. J Micromech Microeng (18)035036
Singh A, Metwally K, Michel G, Queste S, Robert L, Malek CK (2011) Injection moulding using an exchangeable Si mould insert. Micro Nanosyst 3:230–235
Shen YK, Chang HJ, Lin CT (2006) Study on optical properties of microstructure of lightguiding plate for micro injection molding and micro injection-compression molding. Mater Sci Forum 505–507:229–234
Shan XC, Maeda R, Murakoshi Y (2003) Micro hot embossing for replication of microstructures. Jpn J Appl Phys 42:3859–3862
Lee BK, Kim DS, Kwon TH (2004) Replication of microlens arrays by injection molding. Microsyst Technol 10:531–535
Huang K (2008) Rapid replication of nanostructures made with a polymer using simple injection molding. J Appl Polym Sci 107:497–500
Hattori S, Nagato K, Hamaguchi T, Nakao M (2010) Rapid injection molding of high-aspect-ratio nanostructures. Microelectron Eng 87(2010):1546–1549
Holger Becker H, Heim U (2000) Hot embossing as a method for the fabrication of polymer high aspect ratio structures. Sensors Actuators 83:130–135
Griffiths CA, Dimov SS, Brousseau EB, Packianather MS (2008) The finite element analysis of melt flow behaviour in micro-injection moulding. IMechE B: J Eng Manuf 222:1107–1118
Romankiw LT, Croll IM, Hatzakis M (1993) Think small: one day it may be worth a billion. Interface, Summer, p 17–57
Malacara-Hernández D, Malacara-Doblado D (2015) What is a Hartmann test? Appl Opt 54:9
Carvalho LA, Chamon W, Schor P, Castro JC (2006) Quantitative comparison of different-shaped wavefront sensors and preliminary results for defocus aberrations on a mechanical eye. Arq Bras Oftalmol 69(2):239–47
Goodman JW (1996) Introduction to Fourier optics, 2nd edn, chapter 4, p 63
Sinzinger S, Jahns Y (2003) Diffractive microoptics. In: Microoptics, 2nd edn, p 154-158
Seabra AC et al (2000) Increasing the optical coupling efficiency of planar photodetectors: electron beam writing of an integrated microlens array on top of an MSM device. International Topical Meeting on Optical Computing, Quebec, pp 890–894
Rees JD (1982) Non-Gaussian imaging properties of GRIN fiber lens arrays. Appl Opt 21(6):1009–1012
Goodman JW, Dias AR, Woody LM (1978) Fully parallel, highspeed incoherent optical method for performing discrete Fourier transformation. Opt Lett 2(1):1–3
Monteiro DWL (2002) CMOS-based integrated wavefront sensor. Delft University Press, Delft, p 78
Artzner GE (1992) Microlens arrays for Shack-Hartmann wavefront sensors. Opt Eng 31(6):1311–1322
Yoon GY et al (1996) Shack Hartmann wave-front measurement with a large F-number plastic microlens array. Appl Opt 35(1):188–192
Chang SI et al (2006) Microlens array diffuser for a light-emitting diode backlight system. Opt Lett 31(20):3016–3018
Tripathi A, Chronis N (2011) A doublet microlens array for imaging micron-sized objects. J Micromech Microeng 21(10):105024
Aina W, Jun Y, Dongmei C, Hao R (2010) Design and fabrication of a pyramid wavefront sensor. Opt Eng 49(7):073401
Ragazzoni R (1996) Pupil plane wavefront sensing with an oscillating prism. J Mod Opt 43:289
Iglesias I, Ragazzoni R, Julien Y, Artal P (2002) Extended source pyramid wave-front sensor for the human eye. Opt Express 10:419
Chamot SR, Dainty C, Esposito S (2006) Adaptive optics for ophthalmic applications using a pyramid wavefront sensor. Opt Express 14:518, 2525
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Cirino, G.A., Granado, R.M., Mohammed-Brahim, T. et al. Assessment of replication fidelity of optical microstructures by hot embossing. Int J Adv Manuf Technol 88, 303–316 (2017). https://doi.org/10.1007/s00170-016-8757-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8757-3