Abstract
Despite of the studies in the last decades, there are still some gaps in understanding of the distinctive behaviors of orthogonal turn-milling. In order to improve the performance of this new technology, deeper investigations are required. This work deals with the mechanics in non-eccentric orthogonal turn-milling. The engaged areas of both side edge and end edge are analyzed. Then, the boundary conditions used to extract them are derived. The two sets of cutting force coefficients for the side edge and end edge are calibrated based on slot milling and plunge milling, respectively. The total cutting forces are calculated as a sum of the cutting forces on both side edge and end edge. The proposed cutting force model is validated experimentally on a five-axis machine tool. In addition, comparative experiments have been conducted to investigate the effects of cutting depth and longitudinal feed rate on the cutting force in tool axis direction.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Schulz H (1990) High speed turn-milling—a new precision manufacturing technology for the machining of rotationally symmetrical workpiece. CIRP Ann Manuf Technol 39(1):107–109
Schulz H, Kneisel T (1994) Turn-milling of hardened steel—an alternative to turning. CIRP Ann Manuf Technol 43(1):93–96
Choudhury SK, Mangrulkar KS (2000) Investigation of orthogonal turn-milling for the machining of rotationally symmetrical workpieces. J Mater Process Technol 99(1–3):120–128
Savas V, Ozay C (2007) Analysis of the surface roughness of tangential turn-milling for machining with end milling cutter. J Mater Process Technol 186(1–3):279–283
Savas V, Ozay C (2008) The optimization of the surface roughness in the process of tangential turn-milling using genetic algorithm. Int J Adv Manuf Technol 37(3–4):335–340
Karaguzel U, Olgun U, Uysal E, Budak E, Bakkal M (2015) Increasing tool life in machining of difficult-to-cut materials using nonconventional turning processes. Int J Adv Manuf Technol 77(9–12):1993–2004
Pogačnik M, Kopač J (2000) Dynamic stabilization of the turn-milling process by parameter optimization. Proc Instn Mech Engrs Part B 214(2):127–135
Neagu C, Gheorghe M, Dumitrescu A (2005) Fundamentals on face milling processing of straight shafts. J Mater Process Technol 166(3):337–344
Jiang Z, Liu X, Deng X (2011) Modeling and simulation on surface texture of workpiece machined by tangential turn-milling based on matlab, 2nd International Conference on Artificial Intelligence, Management Science and Electronic Commerce. AIMSEC 2011–Proceedings, Zhengzhou, China, pp 4072–4075
Zhu L, Li H, Wang W (2013) Research on rotary surface topography by orthogonal turn-milling. Int J Adv Manuf Technol 69(9–12):2279–2292
Uysal E, Karaguzel U, Budak E, Bakkal M (2014) Investigating eccentricity effects in turn-milling operations. 6th CIRP International Conference on High Performance Cutting, Procedia CIRP, vol 14. Elsevier, Amsterdam, pp 176–181
Peng F, Liu Y, Lin S, Yan R, Yang S, Li B (2015) An investigation of workpiece temperature in orthogonal turn-milling compound machining. Trans ASME J Manuf Sci Eng 137:011014
Cai Y, Ma Y, Huang C, Yao X Swept area modeling and cutter wear study in turn-milling. Int J Adv Manuf Technol. http://dx.doi.org/10.1007/s00170-015-7021-6.
Jiang Z, Jia C (2006) Theoretical cutting force of non-eccentricity orthogonal turn-milling (in Chinese). Chin J Mech Eng 42(9):23–28
Filho JMC (2012) Prediction of cutting forces in mill turning through process simulation using a five-axis machining center. Int J Adv Manuf Technol 58(1–4):71–80
Karagüzel U, Uysal E, Budak E, Bakkal M (2015) Analytical modeling of turn-milling process geometry, kinematics and mechanics. Int J Mach Tools Manuf 91:24–33
Qiu W, Liu Q, Yuan S (2015) Modeling of cutting forces in orthogonal turn-milling with round insert cutters. Int J Adv Manuf Technol 78(5–8):1211–1222
Yan R, Tang X, Peng F, Wang Y, Qiu F. The effect of variable cutting depth and thickness on milling stability for orthogonal turn-milling. Int J Adv Manuf Technol, http://dx.doi.org/10.1007/s00170-015-7418-2.
Dang JW, Zhang WH, Yang Y, Wan M (2010) Cutting force modeling for flat end milling including bottom edge cutting effect. Int J Mach Tools Manuf 50(11):986–997
Wan M, Lu M-S, Zhang W-H, Yang Y (2012) A new ternary-mechanism model for the prediction of cutting forces in flat end milling. Int J Mach Tools Manuf 57:34–45
Liu C, Wang G, Dargusch MS (2012) Modelling, simulation and experimental investigation of cutting forces during helical milling operations. Int J Adv Manuf Technol 63(9–12):839–850
Altintas Y (2000) Manufacturing automation—metal cutting mechanics, machine tool vibrations, and CNC. Cambridge University Press, Cambridge
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Qiu, W., Liu, Q., Ding, J. et al. Cutting force prediction in orthogonal turn-milling by directly using engagement boundaries. Int J Adv Manuf Technol 86, 963–975 (2016). https://doi.org/10.1007/s00170-015-8173-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-8173-0