Abstract
A layer of titanium carbon nitride (TiCN) coating was deposited on YT14 cutting tool by a cathodic arc ion plating (CAIP); the friction-wear behaviors of TiCN coating at the temperatures of 200, 300, and 400 °C were investigated by a high-temperature friction-wear tester. The results show that a metallurgical bonding is formed at the TiCN coating interface, of which the bonding strength is 58.15 N measured by scratch test. The average coefficient of friction (COF) of TiCN coating at the temperatures of 200, 300, and 400 °C is 0.2931, 0.5252, and 0.4114, respectively; the wear rates increase gradually with the wear temperatures. The TiO2 that is produced during the wear improves the lubrication of the coating; the wear mechanisms are primarily composed of oxidation wear, abrasive wear, and adhesive wear, accompanied by slight fatigue wear.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Aslantas K, Ucun İ, Çicek A (2012) Tool life and wear mechanism of coated and uncoated Al2O3/TiCN mixed ceramic tools in turning hardened alloy steel. Wear 274–275:442–451
Chinchanikar S, Choudhury SK (2015) Cutting force modeling considering tool wear effect during turning of hardened AISI 4340 alloy steel using multi-layer TiCN/Al2O3/TiN-coated carbide tools. Int J Adv Manuf Technol. doi:10.1007/s00170-015-7662-5
Kong DJ, Fu GZ (2015) Nanoindentation analysis of TiN, TiAlN and TiAlSiN coatings prepared by cathode ion plating. Sci China Technol Sci 58(1):1360–1368
Rasool G, Mridha S, Stack MM (2015) Mapping wear mechanisms of TiC/Ti composite coatings. Wear 328–329:498–508
Yang YL, Zhang D, Yan W, Zheng YR (2010) Microstructure and wear properties of TiCN/Ti coatings on titanium alloy by laser cladding. Opt Lasers Eng 48:119–124
Ren XY, Peng ZJ, Hu YB, Wang CB, Fu ZQ, Yue W, Qi LH, Miao HZ (2013) Abrasive wear behavior of TiCN cermets under water-based slurries with different abrasives. Tribol Int 66:35–43
Bonny K, De Baets P, Vleugels J et al (2008) Reciprocative sliding wear of ZrO2-TiCN composites against WC-Co cemented carbide. Wear 265(11–12):1767–1775
Vereschaka A, Volosova MA, Batako AD, Vereshchaka AS, Mokritskii BY (2015) Development of wear-resistant coatings compounds for high-speed steel tool using a combined cathodic vacuum arc deposition. Int J Adv Manuf Technol. doi:10.1007/s00170-015-7808-5
Liu Y, Huang CZ, Liu HL, Zou B (2015) Mechanical properties and microstructure of Ti(C5N5)-TiB2-(W7Ti3)C composite cutting tool materials. Int J Adv Manuf Technol 79:949–957
Zou B, Chen M, Li SS (2011) Study on finish-turning of NiCr20TiAl nickel-based alloy using Al2O3/TiN-coated carbide tools. Int J Adv Manuf Technol 53:81–92
Kong DJ, Guo HY (2015) Friction-wear behaviors of AlTiN coating by cathodic arc ion plating at high temperatures. Tribol Int 88:31–39
Downey J, O’Leary P, Raghavendra R (2014) Comparison and analysis of audible sound energy emissions during s ingle point machining of HSTS with PVD TiCN cutter insert across full tool life. Wear 313(1–2):53–62
Tang AT, Chen M, Wang J, Liu CP, Pan FS, Wang WQ (2011) Phase evolution during carbothermic reduction process of ilmenite for TiCxN1-x composite powders. Rare Metal Mater Eng 40(S3):281–285
Li JL, Zhang SH, Li MX (2013) Influence of the C2H2 flow rate on gradient TiCN films deposited by multi-arc ion plating. Appl Sur Sci 283:134–144
Aramcharoen A, Mativenga PT (2008) White layer formation and hardening effects in hard turning of H13 tool steel with CrTiAlN and CrTiAlN/MoST-coated carbide tools. Int J Adv Manuf Technol 36:650–657
Feng WR, Zhou H, YangS Z (2010) Nano-indentation and wear-resistance behaviors of TiCN films by pulsed plasma on cemented carbide cutting tool. Mater Sci Eng A 527:4767–4770
Meng JH, Lu JJ, Wang JB, Yang SR (2006) Tribological behavior of TiCN-based cermets at elevated temperatures. Mater Sci Eng A 418:68–76
Wang QZ, Zhou F, Chen KM, Wang ML, Qian T (2011) Friction and wear properties of TiCN coatings sliding against SiC and steel balls in air and water. Thin Solid Films 519:4830–4841
Wang QZ, Zhou F, Gao S, Zhou ZF, Li LKY, Yan JW (2015) Effect of counterparts on the tribological properties of TiCN coatings with low carbon concentration in water lubrication. Wear 328–329:356–362
Polcar T, Kubart T, Novák R, Kopecký L, Široky Ṕ (2005) Comparison of tribological behaviour of TiN, TiCN and CrN at elevated temperatures. Surf Coat Technol 193:192–199
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Dejun, K., Haoyuan, G. Microstructures and high-temperature wear performances of cathodic arc ion plating on YT14 cutting tool. Int J Adv Manuf Technol 85, 2597–2605 (2016). https://doi.org/10.1007/s00170-015-8140-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-8140-9