Abstract
In electrical discharge machining (EDM) process, one of the most important aspects is the surface quality of the workpiece. When a uniform and thick recast layer is achieved with characteristics of low roughness, high hardness, and the absence of pores and micro-cracks, it acts as a kind of coating. Such surface is required by mold-making industry, where the molds are subjected to chemical and abrasive wear, and the surface needs to present high resistance against corrosion and abrasive forces. The use of powder particles suspended in the dielectric is a way to provide such improvement and, at the same time, avoiding the need for subsequent polishing. This work investigated the influence of silicon and manganese powders with fine particle sizes, using two different concentrations, suspended in the dielectric when EDM machining AISI H13 tool steel. It evaluated the surface roughness, hardness, and the chemical composition and micro-structure of the recast layer; using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) techniques. The best results were obtained for silicon powder; presenting the surface roughness improved about five times, when compared to the conventional EDM process, as well as a thick and uniform recast layer without micro-cracks and pores. The silicon and the manganese powders also promoted an increase of the recast layer hardness of about 40 % when compared to the conventional EDM process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Van Dijck F, Crookal JR, Heuvelman CJ, Snoyes R (1974) Some results of physical research in EDM. IV International Symposium for Electromachining 1:68-85, Bratislava, Poland
Zolotyck BN (1955) Physikalische grundlagen der elektrofunkenbearbeitung von metallen. VEB, Verlag Technik, Berlin
Crookall JR, Khor bC (1974) Electro-discharge surfaces. Proceedings of the Fifteenth International Machine Tool Design and Research Conference 1:373-384, September 18-20, England
Dibitonto DD, Eubank PT, Mukunk RP, Barrufet MA (1989) Theoretical models of the electrical discharge machining process I: a simple cathode erosion model. J Appl Phys 66:4095–4103
König W, Klocke F (1997) Fertigungsverfahren - 3: Abtragen und Generieren. Springer, Berlin
Kruth PDIJ, Stevens IL, Froyen PDIL, Lauwers DIB (1995) Study of the white layer of a surface machined by die-sinking electro-discharge machining. CIRP Annals 44:169–172
Klocke F (1998) The process sequence in tool and die-making. Proceedings of the XII International Symposium for Electromachining 65-97, Aachen, Germany
Tzeng Y, Chen F (2005) Investigation into some surface characteristics of electrical discharge machined SKD-11 using powder-suspension dielectric oil. J Mater Process Technol 170:385–391
Kansal HK, Singh S, Kumar P (2007) Technology and research developments in powder mixed electric discharge machining (PMEDM). J Mater Process Technol 184:32–41
Jeswani LM (1981) Effect of addition of graphite powder to kerosene used as a dielectric fluid in electrical discharge machining. Wear 70:133–139
Stevens L (1998) Improvement of surface quality in die-sinking EDM. Doctorate Thesis Mechanical Engineering, K.U. Leuven
Kumar S, Singh R, Singh TP, Sethi BL (2009) Surface modification by electrical discharge machining: a review. J Mater Process Technol 209:3675–3687
Simao J, Lee HG, Aspinwall DK, Dewes RC, Aspinwall EM (2003) Workpiece surface modification using electrical discharge machining. Int J Mach Tools Manuf 43:121–128
Furutani K, Saneto A, Takezawa H, Mohri N, Miyake H (2000) Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid. Precis Eng 25:138–144
Mohri N et al (2000) A new process of additive and removal machining by EDM with a thin electrode. CIRP Annals 40:123–126
Narumiya H, et.al. (1989) EDM by powder suspended working fluid. Proceedings of the ISEM- 9:5-8, Nagoya, Japan
Wong YS, Lim LC, Rahuman I, Tee WM (1998) Near mirror-finish phenomenon in EDM using powder-mixed dielectric. J Mater Process Technol 79:30–40
Peças P, Henrique H, Raposo L (2001) Electrical discharge machining with additive: a way of mold steels non-manual polishing. Proceedings of the First International Seminar in Innovative Manufacturing Engineering 1:267-271, CIRP, Genève
Peças P, Henriques E (2008) Effect of the powder concentration and dielectric flow in the surface morphology in electrical discharge machining with powder-mixed dielectric (PMD-EDM). Int J Adv Manuf Technol 37:1120–1132
Mohri N, Tsukamoto J, Fujino M (1985) Mirror-like finishing by EDM. Proceedings of the 25th International Symposium on Machine Tool Design and Research 1:329-336, UK
Mohri N, Tsukamoto J, Fujino M (1988) Surface modification by EDM—an innovation in EDM with semi-conductive electrodes. Proceedings of Winter Annual Meet ASME 34:21-30
Mohri N, Saito N, Higashi MA (1991) A new process of finish machining on free surface by EDM methods. CIRP Annals 1:207–210
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Molinetti, A., Amorim, F.L., Soares, P.C. et al. Surface modification of AISI H13 tool steel with silicon or manganese powders mixed to the dielectric in electrical discharge machining process. Int J Adv Manuf Technol 83, 1057–1068 (2016). https://doi.org/10.1007/s00170-015-7613-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7613-1