Abstract
In this paper, a laser-generated shock wave was used to induce plastic deformation of metallic foils using Plasticine as a flexible support. In this new micro-drawing process, the laser-generated shock wave and the Plasticine are used to replace the conventional metal punch and mold. By undergoing large plastic deformation under the laser-generated shock wave, Plasticine accurately keeps the shape of the deformed workpiece, thereby improving the forming quality. Moreover, this is a damage-free forming process because the Plasticine is softer than metal foils. The feasibility of this new drawing process was conducted experimentally on aluminum, cooper, and titanium foils. The thickness distribution at the cross-section of the work piece was studied to evaluate the risk of crack. Meanwhile, the arrays of craters were fabricated on titanium foils. The results show that mold-free laser shock micro-drawing forming is an effective method to fabricate controlled micro-craters on metallic foils.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Jeong HW, Hata S, Shimokohbe A (2003) Microforming of three-dimensional microstructures from thin-film metallic glass [J]. J Microelectromech Syst 12(1):42–52
Vollertsen F, Hu Z, Niehoff HS, Theiler C (2004) State of the art in micro forming and investigations into micro deep drawing [J]. J Mater Process Technol 151(1):70–79
Dirscherl M, Esser G, Schmidt M (2006) Ultrashort pulse laser bending [J]. J Laser Micro/Nanoeng 1(1):54–60
Ocaña JL, Morales M, Porro JA, García-Ballesteros JJ, Correa C (2011) Laser shock microforming of thin metal sheets with ns lasers [J]. Phys Procedia 12:201–206
Saotome Y, Yasuda K, Kaga H (2001) Microdeep drawability of very thin sheet steels [J]. J Mater Process Technol 113(1):641–647
Jaisingh A, Narasimhan K, Date P, Maiti S, Singh U (2004) Sensitivity analysis of a deep drawing process for miniaturized products [J]. J Mater Process Technol 147(3):321–327
Peng L, Hu P, Lai X, Mei D, Ni J (2009) Investigation of micro/meso sheet soft punch stamping process—simulation and experiments [J]. Mater Des 30(3):783–790
Niehoff SH, Vollertsen F (2005) Laser induced shock waves in deformation processing [J]. Metalurgija 11(3):183–194
Yilbas B, Mansoor S, Arif A (2009) Laser shock processing: modeling of evaporation and pressure field developed in the laser-produced cavity [J]. Int J Adv Manuf Technol 42(3–4):250–262
Irizalp SG, Saklakoglu N, Yilbas BS (2014) Characterization of microplastic deformation produced in 6061-T6 by using laser shock processing [J]. Int J Adv Manuf Technol 71(1–4):109–115
Edwards KR, Edwardson SP, Carey C, Dearden G, Watkins KG (2010) Laser micro peen forming without a tamping layer [J]. Int J Adv Manuf Technol 47(1–4):191–200
Zhou JZ, Yang JC, Zhang YK, Zhou M (2002) A study on super-speed forming of metal sheet by laser shock waves [J]. J Mater Process Technol 129(1–3):241–244
Zhou M, Zhang YK, Cai L (2002) Laser shock forming on coated metal sheets characterized by ultrahigh-strain-rate plastic deformation [J]. J Appl Phys 91(8):5501–5503
Zhou M, Zhang YK, Cai L (2003) Ultrahigh-strain-rate plastic deformation of a stainless-steel sheet with TiN coatings driven by laser shock waves [J]. Appl Phys a-Mater 77(3–4):549–554
Cheng GJ, Pirzada D, Ming Z (2007) Microstructure and mechanical property characterizations of metal foil after microscale laser dynamic forming [J]. J Appl Phys 101(6):063108–7
Vollertsen F, Niehoff HS, Wielage H (2009) On the acting pressure in laser deep drawing [J]. Prod Eng 3(1):1–8
Liu H, Shen Z, Wang X, Wang H, Tao M (2010) Micromould based laser shock embossing of thin metal sheets for MEMS applications [J]. Appl Surf Sci 256(14):4687–4691
Fleischer J, Kotschenreuther J (2007) The manufacturing of micro molds by conventional and energy-assisted processes [J]. Int J Adv Manuf Technol 33(1–2):75–85
Qin Y, Brockett A, Ma Y, Razali A, Zhao J, Harrison C, Pan W, Dai X, Loziak D (2010) Micro-manufacturing: research, technology outcomes and development issues [J]. Int J Adv Manuf Technol 47(9–12):821–837
Nagarajan B, Castagne S, Wang ZK (2013) Mold-free fabrication of 3D microfeatures using laser-induced shock pressure [J]. Appl Surf Sci 268:529–534
Shuqin X, Yuan F (1997) FEM analysis and experimental research on complex forming [J]. J Mater Process Technol 69(1):208–211
Sofuoglu H, Rasty J (2000) Flow behavior of Plasticine used in physical modeling of metal forming processes [J]. Tribol Int 33(8):523–529
Sofuoglu H, Gedikli H (2004) Physical and numerical analysis of three dimensional extrusion process [J]. Comput Mater Sci 31(1–2):113–124
Sofuoglu H (2006) A technical note on the role of process parameters in predicting flow behavior of plasticine using design of experiment [J]. J Mater Process Technol 178(1–3):148–153
Montross CS, Wei T, Ye L, Clark G, Mai Y-W (2002) Laser shock processing and its effects on microstructure and properties of metal alloys: a review [J]. Int J Fatigue 24(10):1021–1036
Liu H, Hu Y, Wang X, Shen Z, Li P, Gu C, Liu H, Du D Guo C (2012) Grain refinement progress of pure titanium during laser shock forming (LSF) and mechanical property characterizations with nanoindentation [J]. Mater Sci Eng A
Maawad E, Sano Y, Wagner L, Brokmeier H-G, Genzel C (2012) Investigation of laser shock peening effects on residual stress state and fatigue performance of titanium alloys [J]. Mater Sci Eng A 536:82–91
Li J, Cheng GJ (2010) Multiple-pulse laser dynamic forming of metallic thin films for microscale three dimensional shapes [J]. J Appl Phys 108(1):013107–013108
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, D., Lin, Y., Gu, C. et al. A mold-free laser shock micro-drawing forming process using Plasticine as the flexible support. Int J Adv Manuf Technol 79, 265–272 (2015). https://doi.org/10.1007/s00170-015-6809-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-6809-8