Abstract
In this paper, the “trial-and-repair” process of the extrusion die is transferred from the workshop to the computer for a complex hollow aluminum profile used in high-speed trains. Firstly, a finite element (FE) model of the extrusion process is established with the arbitrary Lagrangian–Eulerian code HyperXtrude. To balance the material flow velocity in the die cavity, more than ten baffle plates are used and distributed in the welding chamber. Then, taking the exit velocity uniformity as the evaluating criterion, the initial extrusion die is modified by adjusting the shapes, the layout, and the heights of the baffle plates. Through a series of modifications, the velocity difference in the cross-section of the extrudate decreases significantly from 102.3 mm/s with the initial die to 26.6 mm/s with the final one. The local twisted or bent deformation of the extrudate is well controlled with the optimal die. Finally, a real extrusion die is manufactured and a practical profile is extruded. The difference in the rib thickness of the profile between the experimental measurements and desired dimensions is 0.12 mm, which satisfies the practical requirements. Moreover, the microstructures in the profile and its ribs are examined, and no heat defects are observed in the profile. Therefore, the virtual tryout of the extrusion die in this work are well verified, and the design rules of extrusion dies could provide theoretical guidance for practical repairs of complex extrusion dies in workshop.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Reiso O (2004) Extrusion of AlMgSi alloys. Mater Forum 28:32–46
Koopman AJ (2008) Analysis tools for the design of aluminium extrusion dies. Dissertation, University of Twente
Lee JM, Kim BM, Kang CC (2005) Effects of chamber shapers of porthole die on elastic deformation and extrusion process in condenser tube extrusion. Mater Des 26:327–336
Peng Z, Sheppard T (2005) Effect of die pockets on multi-hole die extrusion. Mater Sci Eng A407:89–97
Kloppenborg T, Schwane M, Ben Khalifa N, Tekkaya AE, Brosius A (2012) Experimental and numerical analysis of material flow in porthole die extrusion. Key Eng Mater 491:97–104
Carmai SJJ, Pitakthapanaphong S, Sechjarern S (2008) 3D finite element analysis of metal flow in hot aluminium extrusion of T-shaped profile with various offset pockets. J Achiev Mater Manuf Eng 31:463–468
Donati L, Tomesani L, Shikorra M (2009) The effect of pocket shape in extrusion dies. Int J Mater Form 2:97–100
He YF, Xie SS, Cheng L, Huang GJ, Fu Y (2010) FEM simulation of aluminum extrusion process in porthole die with pockets. Trans Nonferrous Metals Soc China 20:1067–1071
Fang G, Zhou J, Duczczyk J (2010) FEM-assisted design of a multi-hole pocket die to extrude U-shaped aluminum profiles with different wall thicknesses. Key Eng Mater 424:213–220
Chen H, Zhao GQ, Zhang CS, Liu JW (2011) Effects of welding chamber step on extrusion process of a complex hollow profile. Adv Mater Res 148–149:1684–1688
Chen H, Zhao GQ, Zhang CS, Wen DS (2011) Effects of multi-step welding chamber on extrusion product quality and die strength. Appl Mech Mater 44–47:311–315
Zhang CS, Zhao GQ, Sun XM, Chen H, Gao BJ (2011) Optimization design of baffle plates in porthole die for aluminum profile extrusion. J Mater Des Appl 225:255–265
Li F, Jin JF, Guan J, Liu XJ (2009) Effect of inner cone punch on metal flow in extrusion process. Int J Adv Manuf Technol 42:489–496
Rout AK, Maity K (2011) Numerical and experimental study on the three-dimensional extrusion of square section from square billet through a polynomial-shaped curved die. Int J Adv Manuf Technol 54:495–506
Hwang YM, Chen JM (2013) Surface permeation and die design during rod extrusion processes. Int J Adv Manuf Technol 69:397–403
Liu P, Xie SS, Cheng L (2012) Die structure optimization for a large, multi-cavity aluminum profile using numerical simulation and experiments. Mater Des 36:152–160
Lof L, Blokhuis Y (2002) FEM simulations of the extrusion of complex thin-walled aluminium sections. J Mater Process Technol 122:344–354
HyperXtrude 10.0 manual, Altair Engineering, Inc.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, C., Zhao, G., Guan, Y. et al. Virtual tryout and optimization of the extrusion die for an aluminum profile with complex cross-sections. Int J Adv Manuf Technol 78, 927–937 (2015). https://doi.org/10.1007/s00170-014-6691-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6691-9