Abstract
Higher requirement of the performance of spline shaft has been put forward with the development of aerospace technology. As a precision advanced manufacturing technology, radial forging technology is suitable for the manufacturing of high-performance spline shaft. Aiming at the influence of process parameters on plastic forming in single-tooth radial forging (STRF) process of spline shaft, the effects of process parameters such as initial forging temperature of the blank, forging speed of the dies, and friction condition on the forming load, and distribution of equivalent stress and equivalent strain of the workpiece were investigated. Firstly, the introduction to STRF process of spline shaft was given. And then a finite element model was established based on the FORGE software, and the range of each process parameter was determined. Through the finite element analysis, the influence laws of various parameters of STRF process on spline shaft forming were obtained. The simulation results show that the forming load and equivalent stress decrease with the increasing of the initial forging temperature of the blank, and increase with the increasing of the forging speed. Within the friction coefficient range, the effect of friction conditions on die load and equivalent stress is not significant. The equivalent strain and the cumulative plastic deformation degree of the material are almost unchanged under different parameter condition. The obtained results in this paper can provide reference for the application and development of advanced manufacturing process of high-performance gear parts used in aerospace.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Li Y, Zhao S, Zhao Y et al (2014) Analysis and experiment on the effect of system parameters on the axial-infeed rolling forming process of spline shaft. J Mech Eng 50(22):50–56 (in Chinese)
Luo Y, Ma Z, Fang X et al (2021) Influencing factors of effective tooth depth in the cylindrical gear rolling process with axial infeed. Int J Adv Manuf Technol 118:497–510
Fu X, Wang B, Wang T (2021) Experimental and numerical investigations on the deformation defects by gear rolling process with local induction heating. Int J Adv Manuf Technol 117:835–844
Hou H, Zhao Y, Cui M et al (2021) Experimental study on the axial-infeed incremental warm rolling process for spline shaft production. Int J Adv Manuf Technol 112:2177–2186
Wang Z et al (2008) Numerical simulation of involutes spline shaft in cold rolling forming. J Cent South Univ Technol 15(S2):278–283
Zhang D, Zhao S, Wu S et al (2015) Phase characteristic between dies before rolling for thread and spline synchronous rolling process. Int J Adv Manuf Technol 81:513–528
Lu Q, Yu D et al (2020) Analysis on fracture of output spline shaft for a certain type of turbine stater. Aviat Maint Eng (10):109–112
Li K, Zhao S et al (2021) Discussion of near net forming process for complex curved tooth profile using radial forging. Heavy Mach (05):19–23
Simonov MY, Shaimanov GS et al (2016) Effect of structure on the dynamic crack resistance and special features of the micromechanism of crack growth in steel 35Kh after cold radial forging. Met Sci Heat Treat 58(1–2):82–90
Darki S, Raskatov EY (2020) Analysis of the hot radial forging process according to the finite element method. Int J Adv Manuf Technol 110:1061–1070
Panov D, Pertsev A, Smirnov A et al (2019) Metastable austenitic steel structure and mechanical properties evolution in the process of cold radial forging. Materials (Basel) 12(2058):1–18
Li K, Zhao S, Zhang C et al (2022) Deformation behavior during single-tooth radial forging of large-scale spline shaft. J Plast Eng 29(02):69–75 (in Chinese)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this chapter
Cite this chapter
Li, K., Zhao, S., Zhang, D., Zhang, C. (2024). Study on Effect of Single-Tooth Radial Forging Process Parameters on Spline Shaft Forming. In: Liu, Z., Li, R., He, X., Zhu, Z. (eds) Advances and Challenges in Advanced Unmanned Aerial Systems. ICAUAS 2023. Springer Aerospace Technology. Springer, Singapore. https://doi.org/10.1007/978-981-99-8045-1_41
Download citation
DOI: https://doi.org/10.1007/978-981-99-8045-1_41
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-8044-4
Online ISBN: 978-981-99-8045-1
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)