Abstract
This paper addresses the control problem for active suspensions of the in-wheel motor driven electric vehicle with consideration of time delay and cyber attacks. The main purpose is to develop an adaptive sliding mode control (SMC) method to improve the suspension performances by handling the issues of time delay and cyber attacks. Firstly, by considering a dynamic vibration absorber to mitigate vibrations, an active suspension model is constructed, in which both the spring dynamic nonlinearity and the damper dynamic segmentation are approximated by the Takagi-Sugeno fuzzy model. Secondly, by introducing an integral-type sliding surface, sufficient conditions are developed to ensure the sliding motion satisfies the asymptotical stability and desired performance requirements despite the occurrence of time delay. Based on the reachability to the sliding surface, a SMC approach is developed such that the closed-loop suspension system can achieve the desired performances of the sliding surface. For a better calculation of the controller gains, the controller design condition is converted to an optimization problem. Finally, various simulation tests are implemented to verify the merits of the proposed adaptive control method.
ICANDVC2023 best presentation paper
Access provided by Autonomous University of Puebla. Download conference paper PDF
Similar content being viewed by others
Keywords
1 Introduction
The electric vehicle has been devoted a great deal of efforts in last decades because it has the advantages of energy-saving and environmental friendliness [1,2,3,4,5]. Specifically, the in-wheel motor-driven (IWMD) vehicle has the prominent advantages of independently and precisely controllable torque, high transmission efficiency, large torque, and fast response. As a result, the IWMD electric vehicle is the main development direction of electric vehicles [6]. However, in the IWMD electric vehicles, installing the motors in the drive wheels indicates that the excitation is directly transmitted to the vehicle body. At the same time, in un-sprung modes, the frequency of vertical excitation increases and the ride comfort and contact stability performance decreases. Hence, some treatments are needed to reduce the impact on ride comfort [7]. Bridgestone company has designed a suspension structure with a wheel motor, which is effective to improve the suspension performances as a dynamic vibration absorber (DVA). It can greatly counteract the road vibration inputs and improve the road holding performance compared to the conventional electric vehicles, but this structure requires the use of active suspension control [8, 9]. Hence, the advanced control technologies of the suspension systems are important to promote the development of IWMD electric vehicles.
To improve suspension responses, many control methods were presented in the field of active suspension control including the adaptive control [10], the robust control [11], the neural network control [12], the sliding model control (SMC) [13] and so on [14,15,16,17]. Among the above control methods, the SMC possesses the advantages of strong robustness and ability to maintain stability despite the system uncertainties and external disturbances. However, traditional SMC usually faces an obvious chattering phenomenon. In line of this consideration, various methods including the terminal SMC, the higher-order SMC and the adaptive sliding model control have been presented to avoid the above problem and to improve the control performances [18]. However, the former two approaches have the disadvantages of needing accurate mathematical models and complicated controller design. Based on the above-mentioned issues, the adaptive SMC approach has been widely investigated [19, 20]. The authors in [21] investigated the adaptive SMC problem for the stabilization of Markovian jump systems. The authors in [22] proposed an adaptive SMC method for the uncertain active suspensions.
The wide application of network brings many benefits, such as improving the system operation rate and communication efficiency. On the other hand, the network may also generate some problems such as time delay and cyber attacks [23]. For electric vehicles, due to the interaction of information among sensors, controllers, and actuators, the active suspension systems are easily susceptible to the cyber attacks. The cyber attacks consume or take up reasonable resources of the system by using malicious data, which may degrade the control performances of active suspensions [24]. To deal with the cyber attacks, the SMC has been widely investigated due to its obvious advantages in resisting external disturbance [25]. However, the parameter uncertainties and time delay were not fully addressed in the above adaptive SMC methods.
In the control strategy of the vehicle, the signal transmission inevitably causes time delay. It should be noted that the time delay can decrease the stability and responses of the vehicle suspension systems [5, 26]. In recent years, there are many control strategies for the time-delay active suspensions, but most of them ignored the cyber attacks [27,28,29]. Although the adaptive SMC has an advantage in handling the cyber attacks, it is still necessary to consider the time delay in the design process of adaptive sliding mode controller.
This paper aims to develop an adaptive SMC method for the IWMD vehicle active suspensions subject to time delay and cyber attacks. This paper has the following features as: (1) An active suspension model is established by considering the spring and damper dynamic nonlinearities, dynamic vibration absorber, time delay and cyber attacks. (2) An integral-type sliding surface is established with consideration of time delay. (3) An adaptive SMC method is proposed to improve the vehicle suspension performance and meet the suspension constraint requirements.
2 Problem Formulation
2.1 Suspension Model of IWMD Vehicles
To simplify the complexity of the suspension dynamics analysis and controller design, a quarter-vehicle suspension model is considered. It can be seen from Fig. 1 that the suspension dynamics can be described as:
where \(z_{d}\), \(z_{u}\) and \(z_{s}\) stand for the vertical displacements of the motor mass \(m_{d}\), un-sprung mass \(m_{u}\) and sprung mass \(m_{s}\). \(z_{w}\) and \(u(t)\) denote the road disturbances and the actuator force. The suspension damping and stiffness coefficients are \(k_{s}\) and \(c_{s}\). The motor damping and stiffness coefficients are \(k_{d}\) and \(c_{d}\). The tire damping and stiffness coefficients are \(k_{t}\) and \(c_{t}\), respectively. And the nonlinear stiffness and damping coefficients are described as [30, 31]:
where \(n\) is the ratio of nonlinear to linear segment \(k_{l}\) of the stiffness coefficient. \(c_{s1}\) and \(c_{s2}\) represent damping coefficient of extension and compression. Defining two premise variables as \(\delta_{1} (t) = (z_{s} - z_{u} )^{2}\) and \(\delta_{2} (t) = \dot{z}_{s} - \dot{z}_{u}\), Eq. (2) can be morphed into
where \(\upsilon (t)\) is a step function.
Regarding to the controller design, the following four key suspension performances are considered as [32]: (1) Ride comfort: It is usually characterized by the body acceleration, thus the following condition is considered:
(2) Handling stability: It can be characterized by the suspension travel, which needs to be smaller than its maximum value, namely,
(3) Road holding ability: The tire should be connected to the road closely and firmly, requiring the dynamic load less than or equal to static load, namely,
Defining the state vector as \(x(t) = \left[ {\begin{array}{*{20}c} {z_{s} - z_{u} } & {\dot{z}_{s} } & {z_{d} - z_{u} } & {\dot{z}_{d} } & {z_{u} - z_{w} } & {\dot{z}_{u} } \\ \end{array} } \right]^{T}\) the road perturbate input as \(\omega (t) = \dot{z}_{w}\), and the control output as \(z(t) = \left[ {\begin{array}{*{20}c} {\ddot{z}_{s} } & {a_{1} (z_{s} - z_{u} )} & {a_{2} (z_{d} - z_{u} )} & {a_{3} (z_{u} - z_{w} )} \\ \end{array} } \right]^{T}\), the suspension model can be converted to
where
Moreover, since the opening-up property of the IWMD vehicle, the cyber attacks are considered when building the suspension system model, which can be shown as
where \(h(x(t))\) represents the cyber attacks on suspension system, which meets the following condition and \(\varepsilon > 0\) is a constant:
Based on (2)-(3), the membership functions are
Therefore, the condition \(\delta_{1} (t) = P_{1} (\delta_{1} (t))z_{\min }^{2} + P_{2} (\delta_{1} (t))z_{\max }^{2}\) can be obtained with \(P_{1} (\delta_{1} (t)) + P_{2} (\delta_{1} (t)) = 1\). Then, the following Takagi-Sugeno (T-S) fuzzy model is obtained as:
Fuzzy Rule \(i\): IF \(\delta_{1} (t)\) is \(P_{v} (\delta_{1} (t))\) and \(\delta_{2} (t)\) is \(Q_{v} (\delta_{2} (t))\), THEN
where \(v = 1,2\) and \(i = 1,2,3,4\). And the matrices \(A_{i}\), \(B_{1i}\), \(B_{2i}\), \(C_{i}\), \(D_{1i}\) and \(D_{2i}\) of system can be obtain by corresponding \(\delta_{1} (t)\) and \(\delta_{2} (t)\), respectively. Furthermore, one has
where the grades of membership \(\eta_{i}\) satisfies \(\eta_{i} \ge 0\) and \(\sum\nolimits_{i = 1}^{4} {\eta_{i} } = 1\), and \(\eta_{1} = P_{1} (\delta_{1} (t)) \times Q_{1} (\delta_{2} (t))\), \(\eta_{2} = P_{1} (\delta_{1} (t)) \times Q_{2} (\delta_{2} (t))\), \(\eta_{3} = P_{2} (\delta_{1} (t)) \times Q_{1} (\delta_{2} (t))\), \(\eta_{4} = P_{2} (\delta_{1} (t)) \times Q_{2} (\delta_{2} (t))\).
2.2 Adaptive Sliding Mode Controller
Firstly, the following sliding surface is constructed as:
where the constant matrix \(H \in \Re^{1 \times 4}\) will be design to guarantee that \(HB_{2i}\) is nonsingular and \(HB_{1i} = 0\). Based on the parallel distribution compensation, the following control law can be obtained:
Control Rule \(j\): IF \(\delta_{1} (t)\) is \(P_{v} (\delta_{1} (t))\) and \(\delta_{2} (t)\) is \(Q_{v} (\delta_{2} (t))\), THEN
where the local control gain matrix \(K_{j}\) will be obtained by subsequent calculations. Hence, we have the global fuzzy controller as follows:
By combining Eq. (14) and Eq. (12), the closed-loop model of IWMD vehicle active suspension system is
As shown in Fig. 2, the control flow of the IWMD vehicles nonlinear suspension is presented. The active suspension system is subject to both road interference and cyber attacks. However, the closed-loop system (15) will be asymptotically stable and achieve the desired performance after being processed by the designed sliding mode controller. In a word, a robust adaptive SMC method is proposed for the IWMD vehicle active suspension such that the asymptotical stability and the following condition are satisfied:
3 Main Results
3.1 Stability Analysis of the Sliding Motion
Theorem 1.
For the given positive scalars \(\tau_{1}\), \(\tau_{2}\), \(\gamma\), \(\kappa_{1}\), \(\kappa_{2}\), and control gains \(\overline{K}_{j}\). The closed-loop system (15) ensure the asymptotical stability and guarantee the \(H_{\infty }\) performance in (16), if there exist positive definite matrices \(\overline{E}_{1}\), \(\overline{E}_{2}\), \(\overline{F}_{1}\), \(\overline{F}_{2}\), \(\overline{X}\), general matrix \(\overline{W}\) that satisfies \(\left[ {\begin{array}{*{20}c} {\overline{F}_{2} } & {\overline{W}} \\ * & {\overline{F}_{2} } \\ \end{array} } \right] > 0\), such that
where \(i,j = 1,2,3,4\) \(\overline{\Theta }_{ij} = \left[ {\begin{array}{*{20}c} {\overline{\Lambda }_{ij}^{11} } & {\overline{\Lambda }_{ij}^{12} } \\ * & {\overline{\Lambda }_{ij}^{22} } \\ \end{array} } \right]\), and
\(\overline{\Lambda }_{22} { = }diag\{ 2\kappa \overline{X} - \kappa^{2} \overline{F}_{1} ,2\kappa \overline{X} - \kappa^{2} \overline{F}_{2} , - I\}\), \(\overline{\Lambda } = [\overline{X}A_{i} ]_{s} + \overline{E}_{1} + \overline{E}_{2} - \overline{F}_{1}\).
Moreover, the control gain is calculated as \(K_{j} = \overline{K}_{j} \overline{X}^{ - 1}\).
Proof.
Constructing a Lyapunov function as:
The derivative of (20) is obtained as
Based on Jensen’s inequality [33], the following condition holds
According to Reciprocal convex inequality [34], it follows that
And the matrix \(W\) meets the conditions \(\left[ {\begin{array}{*{20}c} {F_{2} } & W \\ * & {F_{2} } \\ \end{array} } \right] > 0\).
Combining (21)–(23), the following condition can be obtained:
where \(\varsigma^{T} (t) = col\{ x(t),\dot{x}(t),x(t - \tau_{1} ),x(t - \tau (t)),x(t - \tau_{2} ),\omega (t)\}\), and
where \(\Theta_{ij} = \Lambda_{ij}^{11} - \Lambda_{ij}^{12} \Lambda_{22}^{ - 1} (\Lambda_{ij}^{12} )^{T}\). In other words, when the following condition is true, \({\mathcal{J} < 0}\) holds:
Moreover, when \(\omega (t) = 0\), the derivative \(\dot{V}(t) < 0\) of Lyapunov function can be easily obtained, thus the IWMD vehicle active suspension system (15) is asymptotically stable. Under \(V(0) = 0\) and \(V(\infty ) \ge 0\), one has
Thus, the \(H_{\infty }\) performance can be guaranteed.
Define \(\Xi = diag\{ X^{ - 1} ,X^{ - 1} ,X^{ - 1} ,X^{ - 1} ,I,I,I,I\}\), and pre- and post-multiply \(\Xi\) and its transposition to (26) and (27). Define \(K_{j} = \overline{K}_{j} \overline{X}^{ - 1}\), \(\overline{E}_{1} = X^{ - 1} E_{1} X^{ - 1}\), \(\overline{E}_{2} = X^{ - 1} E_{2} X^{ - 1}\), \(\overline{F}_{1} = X^{ - 1} F_{1} X^{ - 1}\), \(\overline{F}_{2} = X^{ - 1} E_{2} X^{ - 1}\), and \(\overline{W} = X^{ - 1} W_{3} X^{ - 1}\). Based on Schur complement and \(\overline{X}\overline{F}_{\alpha }^{ - 1} \overline{X} \le 2\kappa_{\alpha } \overline{X} - \kappa_{{_{\alpha } }}^{2} \overline{F}_{\alpha }\), the Eqs. (17) and (18) can be obtained. Thus, the asymptotic stability and the performance (16) of the suspension system (15) can be guaranteed.
3.2 Reachability Analysis
Theorem 2.
The active suspension system (15), can approach a specified sliding mode surface \(s(t) = 0\) in limited time with the following SMC strategy as
where \(\varphi (t) = \mu + \varepsilon (t)\left\| {x(t)} \right\|\), and the updating rule of \(\varepsilon (t)\) can be expressed as
where \(\mu > 0\) and \(\rho > 0\) the known constants.
Proof:
Considering the Lyapunov function \(V_{s} (t)\) shown below:
Combining (13) and (29), the derivative of sliding-surface function \(s(t)\) can be derived as
In addition, the derivative of \(V_{s} (t)\) can be expressed as
where \(\left\| {s(t)} \right\| \ne 0\), which indicates the trajectories of the suspension system can all arrive at the specified sliding-mode surface \(s(t) = 0\) in a finite time.
4 Simulation Results
Various simulations are carried out to verify the performance of the adaptive SMC for active suspensions of IWMD vehicles under cyber attacks. The parameters of suspension model are shown in Table 1.
Given scalars \(\tau_{1} = 0.015\) s,\(\tau_{2} = 0.020\) s,\(a_{1} = 5\), \(a_{2} = 25\), \(a_{3} = 10\), \(\kappa_{1} = 0.1\), \(\kappa_{2} = 0.1\) and \(\mu = 0.5\), \(\rho = 0.1\), and the matrix \(H = [\begin{array}{*{20}c} {100} & {100} & 0 & 0 & {100} & {100} \\ \end{array} ]\) such that \(HB_{2i}\) is nonsingular and \(HB_{1i} = 0\). And the function of cyber attacks is set as \(h(x(t)) = - \sum\nolimits_{j = 1}^{4} {0.2K_{j} x(t)}\). To highlight the effectiveness of the proposed method, the robust H∞ control method is selected as a comparison, which is labeled ‘Comparison’ in subsequent results. In addition, the \(H\infty\) performance index \(\gamma_{\min } = {17}{\text{.2039}}\) and controller gains can be obtained by solving Theorem 1.
4.1 Bump Response
The following bumpy road is selected as the disturbance input:
where \(A = 0.05 \, m\) and \(l = 6 \, m\), respectively, and \(v = 10 \, m/s\).
Figure 3 plots the bump response results for IWMD vehicle active suspension systems. Figure 3(a) shows that the body acceleration of the proposed control method has lower peaks than the other two cases, which means the ride comfort is better guaranteed. Figure 3(b)-(c) illustrates that the fluctuation ranges of the suspension travel and tire deflection are smaller than that of the comparison and the passive suspension, which means the handling stability and road holding ability are ensured by the proposed control method. Figure 3(d) illustrates the actuator force under two control strategies. In other words, Fig. 3 shows the adaptive SMC method has an excellent performance.
Figure 4 presents the variation trends of \(s(t)\) and the adaptive parameter \(\varepsilon (t)\). It can be seen from Fig. 4(a) that the sliding variable changes with bump road interference. Figure 4(b) shows that the parameter \(\varepsilon (t)\) varies from the system states to a constant. In addition, Fig. 4 shows that the sliding motion is achieved in finite time.
4.2 Random Response
The following random road excitation is considered:
where \(v_{0} = 5 \, m/s\), \(a = 0.5 \, m/s^{2}\), \(n_{0} { = }0.1 \, m^{ - 1}\) and \(n_{c} { = }0.01 \, m^{ - 1}\), \(n(t)\) denotes a white noise and \(G_{q} (n_{0} ) = 64 \times 10^{ - 6} m^{3}\) is selected in this simulation of random road.
The dynamic responses of the IWMD vehicle suspension system under random response are plotted in Fig. 5. It is observed from Fig. 5(a) that the body acceleration is greatly reduced by the proposed controller compared to the other two cases. Figure 5(b)-(c) presents the suspension travel constraint and the tire deflection constraint are guaranteed, which also shows that the performance of the design SMC method is more outstanding than the comparison and passive suspension. The actuator forces of the proposed control scheme and comparison are revealed in Fig. 5(d).
The changing trends of the sliding surface and adaptive parameter under random road interference are illustrated in Fig. 6. From Fig. 6(a) we can see that the sliding surface \(s(t)\) is changing along with the system state, which means the sliding mode motion can be achieved in a finite time. Figure 6(b) shows that the parameter \(\varepsilon (t)\) increases along with the time, which is in line with the trend of the definition of \(\varepsilon (t)\).
5 Conclusion
An adaptive SMC problem for active suspensions of IWMD electric vehicles under time delay and cyber attacks was investigated in this paper. First of all, a T-S fuzzy model has been constructed to capture the nonlinearity of the IWMD vehicle suspension dynamics, and it provided a powerful foundation for the controller design. Then, a set of sufficient conditions were developed to ensure the asymptotical stability and constraint performances of the sliding motion despite the occurrence of time delay and cyber attacks. Moreover, an adaptive SMC strategy was proposed to guarantee the closed-loop active suspension system can achieve the desired performances guaranteed by the specific sliding surface. Finally, the simulation results illustrated the superiority of the proposed adaptive SMC scheme. In the future, the energy-saving control issue will be investigated for the suspension systems [35, 36].
References
Li, W., Xie, Z., Wong, P.K., et al.: Adaptive-event-trigger-based fuzzy nonlinear lateral dynamic control for autonomous electric vehicles under insecure communication networks. IEEE Trans. Industr. Electron. 68(3), 2447–2459 (2021)
Zhao, J., Li, W., Hu, C., et al.: Robust Gain-scheduling path following control of autonomous vehicles considering stochastic network-induced delay. IEEE Trans. Intell. Transp. Syst. 23(12), 23324–23333 (2022)
Na, J., Huang, Y., Wu, X., et al.: Active adaptive estimation and control for vehicle suspensions with prescribed performance. IEEE Trans. Control Syst. Technol. 26(6), 2063–2077 (2018)
Huang, Y., Na, J., Wu, X., et al.: Approximation-free control for vehicle active suspensions with hydraulic actuator. IEEE Trans. Industr. Electron. 65(9), 7258–7267 (2018)
Huang, Y., Wu, J., Na, J., et al.: Unknown system dynamics estimator for active vehicle suspension control systems with time-varying delay. IEEE Trans. Cybern. 52(8), 8504–8514 (2022)
Zhao, Z., Taghavifar, H., Du, H., et al.: In-wheel motor vibration control for distributed-driven electric vehicles: a review. IEEE Trans. Transp. Electrification 7(4), 2864–2880 (2021)
Gao, Z., Wong, P.K., Zhao, J., et al.: Robust switched H∞ control of T-S fuzzy-based MRF suspension systems subject to input saturation and time-varying delay. IEEE Trans. Industr. Electron. (2023). https://doi.org/10.1109/TIE.2023.3303611
Shao, X., Naghdy, F., Du, H.: Reliable fuzzy H∞ control for active suspension of in-wheel motor driven electric vehicles with dynamic damping. Mech. Syst. Signal Process. 87, 365–383 (2017)
Zhao, J., Dong, J., Wong, P.K., et al.: Interval fuzzy robust non-fragile finite frequency control for active suspension of in-wheel motor driven electric vehicles with time delay. J. Franklin Inst. 359(12), 5960–5990 (2022)
Liu, Y., Zeng, Q., Tong, S., et al.: Adaptive neural network control for active suspension systems with time-varying vertical displacement and speed constraints. IEEE Trans. Industr. Electron. 66(12), 9458–9466 (2019)
Sun, W., Pan, H., Yu, J., et al.: Reliability control for uncertain half-car active suspension systems with possible actuator faults. IET Control Theory Appl. 8, 746–754 (2014)
Zapateiro, M., Luo, N., Karimi, H., et al.: Vibration control of a class of semi-active suspension system using neural network and backstepping techniques. Mech. Syst. Signal Process. 23, 1946–1953 (2009)
Wen, S., Zeng, Z., Yu, X., et al.: Fuzzy control for uncertain vehicle active suspension systems via dynamic sliding-mode approach. IEEE Trans. Syst. Man Cybern.: Syst. 47(1), 24–32 (2017)
Li, W., Xie, Z., Zhao, J., et al.: Static-output-feedback based robust fuzzy wheelbase preview control for uncertain active suspensions with time delay and finite frequency constraint. IEEE/CAA J. Autom. Sinica 8(3), 664–678 (2021)
Na, J., Li, Y., Huang, Y., et al.: Output feedback control of uncertain hydraulic servo systems. IEEE Trans. Industr. Electron. 67(1), 490–500 (2019)
Zhang, C., Na, J., Wu, J., et al.: Proportional-integral approximation-free control of robotic systems with unknown dynamics. IEEE/ASME Trans. Mechatron. 26(4), 2226–2236 (2020)
Na, J., Chen, Q., Ren, X., et al.: Adaptive prescribed performance motion control of servo mechanisms with friction compensation. IEEE Trans. Industr. Electron. 61(1), 486–494 (2014)
Dong, X., Yu, M., Chen, W., et al.: Adaptive fuzzy sliding mode control for magneto-rheological suspension system considering nonlinearity and time delay. J. Vib. Shock 28(11), 55–60 (2009)
Li, H., Yu, J., Liu, H., et al.: Adaptive sliding-mode control for nonlinear active suspension vehicle systems using T-S fuzzy approach. IEEE Trans. Industr. Electron. 60(8), 3328–3338 (2013)
Jin, X., Yang, G.: Adaptive sliding mode fault-tolerant control for nonlinearly chaotic systems against network faults and time-delays. J. Franklin Inst. 350(5), 1206–1220 (2013)
Li, H., Shi, P., Yao, D.: Adaptive sliding-mode control of markov jump nonlinear systems with actuator faults. IEEE Trans. Autom. Control 62(4), 1933–1939 (2017)
Pang, H., Shang, Y., Yang, J.: An adaptive sliding mode-based fault-tolerant control design for half-vehicle active suspensions using T-S fuzzy approach. J. Vib. Control 26(17), 1411–1424 (2020)
Li, W., Wang, ., Zhao, J., et al.: Fuzzy output feedback steering control of lane keeping assistance systems with aperiodic sampling, IEEE/ASME Trans. Mechatron., Accepted for Publication
Cetinkaya, A., Ishii, H., Hayakawa, T.: Networked control under random and malicious packet losses. IEEE Trans. Autom. Control 62(5), 2434–2449 (2017)
Yang, C., Xia, J., Park, J., et al.: Sliding mode control for uncertain active vehicle suspension systems: an event-triggered H∞ control scheme. Nonlinear Dyn. 103, 3209–3221 (2021)
Ding, F., Han, X., Jiang, C., et al.: Fuzzy dynamic output feedback force security control for hysteretic leaf spring hydro-suspension with servo valve opening predictive management under deception attack. IEEE Trans. Fuzzy Syst. 30(9), 3736–3747 (2022)
Zhao, J., Liu, J., Wong, P.K., et al.: Generalized fuzzy subset method for time-varying multi-state reliability of perturbation failure coupling measurement system with limited expert knowledge. IEEE Trans. Fuzzy Syst. 31(7), 2412–2424 (2023)
Ding, F., Shan, H., Han, X., et al.: Security-based resilient triggered output feedback lane keeping control for human–machine cooperative steering intelligent heavy truck under denial-of-service attacks. IEEE Trans. Fuzzy Syst. 31(7), 2264–2276 (2023)
Li, W., Xie, Z., Zhao, J., et al.: Improved AET robust control for networked T-S fuzzy systems with asynchronous constraints. IEEE Trans. Cybern. 52(3), 1465–1478 (2022)
Zhao, J., Wong, P.K., Li, W., et al.: Reliable fuzzy sampled-data control for nonlinear suspension systems against actuator faults. IEEE/ASME Trans. Mechatron. 27(6), 5518–5528 (2022)
Na, J., Huang, Y., Wu, X., et al.: Active suspension control of quarter-car system with experimental validation. IEEE Trans. Syst., Man Cybern.: Syst. 52(8), 4714–4726 (2022)
Na, J., Huang, Y., Wu, X., et al.: Adaptive finite-time fuzzy control of nonlinear active suspension systems with input delay. IEEE Trans. Cybern. 50(6), 2639–2650 (2020)
Zhao, J., Wang, X., Wong, P.K., et al.: Multi-objective frequency domain-constrained static output feedback control for delayed active suspension systems with wheelbase preview information. Nonlinear Dyn. 103(2), 1757–1774 (2021)
Li, W., Xie, Z., Zhao, J., et al.: Human-machine shared steering control for vehicle lane keeping systems via a fuzzy observer-based event-triggered method. IEEE Trans. Intell. Transp. Syst. 23(8), 13731–13744 (2022)
Zhang, M., Jing, X., Zhang, L., et al.: Toward a finite-time energy-saving robust control method for active suspension systems: exploiting beneficial state-coupling, disturbance, and nonlinearities. IEEE Trans. Syst., Man, Cybern.: Syst. 53(9), 5885–5896 (2023)
Zhang, M., Zhou, Z., Zhao, J., et al.: Energy-saving robust tracking control for active suspension systems with beneficial coupling/disturbance, IEEE/ASME Trans. Mechatron. (2023)
Acknowledgements
This work was supported in part by the National Natural Science Foundation of China under Grant 52175127, in part by the Guangdong Basic and Applied Basic Research Foundation under Grant 2022A1515011495, Grant 2022A1515110301 and Grant 2023A1515012327, in part by the research grant of the University of Macau under Grant MYRG2022–00099-FST and Grant MYRG-GRG2023–00235-FST-UMDF, in part by the research grant of the University of Macau under Grant UMMTP-2022-PD01.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Li, W., Zhao, J., Deng, M., Gao, Z., Wong, P.K. (2024). Adaptive Sliding Mode Control for Active Suspensions of IWMD Electric Vehicles Subject to Time Delay and Cyber Attacks. In: Jing, X., Ding, H., Ji, J., Yurchenko, D. (eds) Advances in Applied Nonlinear Dynamics, Vibration, and Control – 2023. ICANDVC 2023. Lecture Notes in Electrical Engineering, vol 1152. Springer, Singapore. https://doi.org/10.1007/978-981-97-0554-2_31
Download citation
DOI: https://doi.org/10.1007/978-981-97-0554-2_31
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-97-0553-5
Online ISBN: 978-981-97-0554-2
eBook Packages: EngineeringEngineering (R0)