Abstract
Hybridization of synthetic with natural fibers has been increasingly studied over the last decades given the potential to partially replace glass fibers with natural ones aiming at meeting both design requirements and environmental concerns. Despite some drawbacks about natural fibers, such as high moisture absorption and low mechanical properties, the combination with synthetic fibers is a suitable route to overcome these drawbacks. Usually, hybrid fiber-reinforced composites need to meet mechanical constraints, and consequently the microstructure of the composite must be taken care of to generate structures with proper mechanical performance. This chapter presents a systematic review on hybrid synthetic/vegetable composites reinforced epoxy composites focusing on research papers published from 2016 to 2020. A total of 531 papers were initially found, but after the exclusion criteria following the PRISMA protocol, 32 articles remained and were included in this review. The presented results focus on the type of microscopy method and analysis of the composites. In brief, this study aims to help to identify the main gaps in the literature related to the proposed topic.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
M.A. Abd El-baky, M.A. Attia, M.M. Abdelhaleem, M.A. Hassan, Mechanical characterization of hybrid composites based on flax, basalt and glass fibers. J. Compos. Mater. 54(27), 4185–4205 (2020)
S.K. Acharya, T. Bera, V. Prakash, S. Pradhan, Effect of stacking sequence on the tribological behaviour of jute-glass hybrid epoxy composite. Mater. Today Proc. [Internet] 28, 936–939 (2019). https://doi.org/10.1016/j.matpr.2019.12.328
Z. Al-Hajaj, R. Zdero, H. Bougherara, Mechanical, morphological, and water absorption properties of a new hybrid composite material made from 4 harness satin woven carbon fibers and flax fibers in an epoxy matrix. Compos. Part A Appl. Sci. Manuf. [Internet] 115, 46–56 (2018). https://doi.org/10.1016/j.compositesa.2018.09.015
J.H.S. Almeida, H.L. Ornaghi, S.C. Amico, F.D.R. Amado, Study of hybrid intralaminate curaua/glass composites. Mater. Des. 42, 111–117 (2012)
J.L.C. Alves, K.S. Prado, J.M.F. de Paiva, Compressive and interlaminar shear strength properties of biaxial fiberglass laminates hybridized with jute fiber produced by vacuum infusion. J. Nat. Fibers [Internet] 00(00), 1–16 (2019). https://doi.org/10.1080/15440478.2019.1697996
S.M.M. Amir, M.T.H. Sultan, M. Jawaid, S.N.A. Safri, A.U.M. Shah, M.R. Yusof, et al., Effects of layering sequence and gamma radiation on mechanical properties and morphology of Kevlar/oil palm EFB/epoxy hybrid composites. J. Mater. Res. Technol. [Internet] 8(6), 5362–5373 (2019). https://doi.org/10.1016/j.jmrt.2019.09.003
A. Behera, J. Dehury, M.M. Thaware, A comparative study on laminated and randomly oriented Luffa-Kevlar reinforced hybrid composites. J. Nat. Fibers [Internet] 16(2), 237–244 (2019). https://doi.org/10.1080/15440478.2017.1414653
M. Bodaghi, C. Cristóvão, R. Gomes, N.C. Correia, Experimental characterization of voids in high fiber volume fraction composites processed by high injection pressure RTM. Compos. Part A Appl. Sci. Manuf. 82, 88–99 (2016)
S.R. Borukati, B.D. Prasad, A. Ramesh, Development and characterization of natural fiber /carbon fiber reinforced hybrid composite material. Mater. Today Proc. [Internet] 18, 5394–5399 (2019). https://doi.org/10.1016/j.matpr.2019.07.567
D.K.K. Cavalcanti, M.D. Banea, J.S.S. Neto, R.A.A. Lima, L.F.M. da Silva, R.J.C. Carbas, Mechanical characterization of intralaminar natural fiber-reinforced hybrid composites. Compos. Part B Eng. [Internet] 175, 107149 (2019). https://doi.org/10.1016/j.compositesb.2019.107149
M. Chapman, H.N. Dhakal, Effects of hybridisation on the low velocity falling weight impact and flexural properties of flax-carbon/epoxy hybrid composites. Fibers 7(11), 95 (2019)
Z. Daneshjoo, M.M. Shokrieh, M. Fakoor, A micromechanical model for prediction of mixed mode I/II delamination of laminated composites considering fiber bridging effects. Theor. Appl. Fract. Mech. [Internet] 2018(94), 46–56 (2018). https://doi.org/10.1016/j.tafmec.2017.12.002
C. Devalve, R. Pitchumani, Simulation of void formation in liquid composite molding processes. Compos. Part A Appl. Sci. Manuf. [Internet] 51, 22–32 (2013). https://doi.org/10.1016/j.compositesa.2013.03.016
H.N. Dhakal, M. Sain, Enhancement of mechanical properties of flax-epoxy composite with carbon fiber hybridisation for lightweight applications. Materials (Basel) 13(1), 109 (2020)
H.N. Dhakal, S.O. Ismail, S.O. Ojo, M. Paggi, J.R. Smith, Abrasive water jet drilling of advanced sustainable bio-fiber-reinforced polymer/hybrid composites: a comprehensive analysis of machining-induced damage responses. Int. J. Adv. Manuf. Technol. 99(9–12), 2833–2847 (2018)
V. Fiore, T. Scalici, D. Badagliacco, D. Enea, G. Alaimo, A. Valenza, Aging resistance of bio-epoxy jute-basalt hybrid composites as novel multilayer structures for cladding. Compos. Struct. [Internet] 160, 1319–1328 (2017). https://doi.org/10.1016/j.compstruct.2016.11.025
P. Ganeshkumar, S. Gopalakrishnan, Systematic reviews and meta-analysis: understanding the best evidence in primary healthcare. J. Fam. Med. Prim. Care 2(1), 9 (2013)
S.C. Garcea, Y. Wang, P.J. Withers, X-ray computed tomography of polymer composites. Compos. Sci. Technol. [Internet] 156, 305–319 (2018). https://doi.org/10.1016/j.compscitech.2017.10.023
R. Giridharan, Preparation and property evaluation of glass/ramie fibers reinforced epoxy hybrid composites. Compos. Part B Eng. [Internet] 167, 342–345 (2019). https://doi.org/10.1016/j.compositesb.2018.12.049
R. Giridharan, M.P. Jenarthanan, Preparation and characterisation of glass and cotton fibers reinforced epoxy hybrid composites. Pigment Resin Technol. 48(4), 272–276 (2019)
L.K. Grunenfelder, S.R. Nutt, Void formation in composite prepregs – effect of dissolved moisture. Compos. Sci. Technol. [Internet] 70(16), 2304–2309 (2010). https://doi.org/10.1016/j.compscitech.2010.09.009
Y.K. Hamidi, L. Aktas, M.C. Altan, Three-dimensional features of void morphology in resin transfer molded composites. Compos. Sci. Technol. 65(7–8), 1306–1320 (2005)
M. J R, G. Goud, Development of Calotropis procera-glass fibers reinforced epoxy hybrid composites: dynamic mechanical properties. J. Nat. Fibers [Internet] 00(00), 1–8 (2020). https://doi.org/10.1080/15440478.2020.1745119
A.S. Jeyasekaran, K.P. Kumar, S. Rajarajan, Numerical and experimental analysis on tensile properties of banana and glass fibers reinforced epoxy composites. Sadhana – Acad. Proc. Eng. Sci. 41(11), 1357–1367 (2016)
A. Karimzadeh, M.Y. Yahya, M.N. Abdullah, K.J. Wong, Effect of stacking sequence on mechanical properties and moisture absorption characteristic of hybrid PALF/glass fiber composites. Fibers Polym. 21(7), 1583–1593 (2020)
M.Y. Khalid, M.A. Nasir, A. Ali, A. Al Rashid, M.R. Khan, Experimental and numerical characterization of tensile property of jute/carbon fabric reinforced epoxy hybrid composites. SN Appl. Sci. [Internet] 2(4) (2020). https://doi.org/10.1007/s42452-020-2403-2
T.S. Lundström, B.R. Gebart, C.Y. Lundemo, Void formation in RTM. J. Reinf. Plast. Compos. 12(12), 1339–1349 (1993)
S. Margabandu, S. Subramaniam, An experimental investigation of thrust force, delamination and surface roughness in drilling of jute/carbon hybrid composites. World J. Eng. 17(5), 661–674 (2020)
C.M. Meenakshi, A. Krishnamoorthy, Study on the effect of surface modification on the mechanical and thermal behaviour of flax, sisal and glass fiber-reinforced epoxy hybrid composites. J. Renew. Mater. 7(2), 153–169 (2019)
D.C.S. Monte Vidal, H.L. Ornaghi, F.G. Ornaghi, F.M. Monticeli, H.J.C. Voorwald, M.O.H. Cioffi, Effect of different stacking sequences on hybrid carbon/glass/epoxy composites laminate: thermal, dynamic mechanical and long-term behavior. J. Compos. Mater. 54(6), 731–743 (2020)
F.M. Monticeli, H.L. Ornaghi, H.J.C. Woorwald, M.O.H. Cioffi, Three-dimensional porosity characterization in carbon/glass fiber epoxy hybrid composites. Compos. Part A Appl. Sci. Manuf. 125, 105555 (2019)
F.M. Monticeli, J.H.S. Almeida, R.M. Neves, F.G. Ornaghi, H.L. Ornaghi, On the 3D void formation of hybrid carbon/glass fiber composite laminates: a statistical approach. Compos. Part A Appl. Sci. Manuf. [Internet] 137, 106036 (2020). https://doi.org/10.1016/j.compositesa.2020.106036
H.L. Ornaghi, A.S. Bolner, R. Fiorio, A.J. Zattera, S.C. Amico, Mechanical and dynamic mechanical analysis of hybrid composites molded by resin transfer molding. J. Appl. Polym. Sci. 118, 887–896 (2010)
S. Paciornik, J. d́Almeida, Digital microscopy and image analysis applied to composite materials characterization. Rev. Mater. 15(2), 183–191 (2010)
A.L. Pereira, M.D. Banea, J.S.S. Neto, D.K.K. Cavalcanti, Mechanical and thermal characterization of natural intralaminar hybrid composites based on sisal. Polymers (Basel) 12(4), 866 (2020)
M. Ramesh, R. Logesh, M. Manikandan, N.S. Kumar, D.V. Pratap, Mechanical and water intake properties of banana-carbon hybrid fiber reinforced polymer composites. Mater. Res. 20(2), 365–376 (2017)
A.K. Reis, F.M. Monticelli, R.M. Neves, L. Felipe, D.P. Santos, Creep behavior of polyetherimide semipreg and epoxy prepreg composites: structure vs. property relationship. J. Compos. Mater. 54, 4121 (2020)
M.J.M. Ridzuan, M.S.A. Majid, M. Afendi, M.N. Mazlee, A.G. Gibson, Thermal behaviour and dynamic mechanical analysis of Pennisetum purpureum/glass-reinforced epoxy hybrid composites. Compos. Struct. [Internet] 152, 850–859 (2016a). https://doi.org/10.1016/j.compstruct.2016.06.026
M.J.M. Ridzuan, M.S. Abdul Majid, M. Afendi, K. Azduwin, N.A.M. Amin, J.M. Zahri, et al., Moisture absorption and mechanical degradation of hybrid Pennisetum purpureum/glass-epoxy composites. Compos. Struct. [Internet] 141, 110–116 (2016b). https://doi.org/10.1016/j.compstruct.2016.01.030
M.J.M. Ridzuan, M.S. Abdul Majid, S.M. Hafis, K. Azduwin, The effects of alkali treatment on the mechanical and morphological properties of Pennisetum purpureum/glass-reinforced epoxy hybrid composites. Plast. Rubber Compos. 46(10), 421–430 (2017)
D. Romanzini, H.L.J. Ornaghi, S.C. Amico, A.J. Zattera, Preparation and characterization of ramie-glass fiber reinforced polymer matrix hybrid composites. Mater. Res. 15(3), 415–420 (2012)
D. Romanzini, A. Lavoratti, H.L. Ornaghi, S.C. Amico, A.J. Zattera, Influence of fiber content on the mechanical and dynamic mechanical properties of glass/ramie polymer composites. Mater. Des. [Internet] 47, 9–15 (2013). https://doi.org/10.1016/j.matdes.2012.12.029
E.H. Saidane, D. Scida, M. Assarar, R. Ayad, Damage mechanisms assessment of hybrid flax-glass fiber composites using acoustic emission. Compos. Struct. [Internet] 174, 1–11 (2017). https://doi.org/10.1016/j.compstruct.2017.04.044
E.H. Saidane, D. Scida, M.J. Pac, R. Ayad, Mode-I interlaminar fracture toughness of flax, glass and hybrid flax-glass fiber woven composites: Failure mechanism evaluation using acoustic emission analysis. Polym. Test [Internet] 75, 246–253 (2019). https://doi.org/10.1016/j.polymertesting.2019.02.022
M.C. Seghini, F. Touchard, F. Sarasini, L. Chocinski-Arnault, M.R. Ricciardi, V. Antonucci, et al., Fatigue behaviour of flax-basalt/epoxy hybrid composites in comparison with non-hybrid composites. Int. J. Fatigue [Internet] 139, 105800 (2020). https://doi.org/10.1016/j.ijfatigue.2020.105800
L. Shamseer, D. Moher, M. Clarke, D. Ghersi, A. Liberati, M. Petticrew, et al., Preferred reporting items for systematic review and meta-analysis protocols (prisma-p) 2015: elaboration and explanation. BMJ [Internet] 349, 1–25 (2015). https://doi.org/10.1136/bmj.g7647
S. Shenoy Heckadka, R. Pai Ballambat, V. Kini Manjeshwar, M. Kumar, P. Hegde, A. Kamath, Influence of stack sequence on the mechanical characteristics of hybrid composites analyzed using cone beam computed tomography and scanning electron microscopy. Polym. Compos. 41, 5059–5071 (2020)
R. Siva, T.N. Valarmathi, K. Palanikumar, A.V. Samrot, Study on a novel natural cellulosic fiber from Kigelia africana fruit: characterization and analysis. Carbohydr. Polym. [Internet] 244, 116494 (2020). https://doi.org/10.1016/j.carbpol.2020.116494
Y. Swolfs, I. Verpoest, L. Gorbatikh, Recent advances in fiber-hybrid composites: materials selection, opportunities and applications. Int. Mater. Rev. [Internet] 64(4), 181–215 (2019). https://doi.org/10.1080/09506608.2018.1467365
M. Venkatasudhahar, P. Kishorekumar, R.N. Dilip, Influence of stacking sequence and fiber treatment on mechanical properties of carbon-jute-banana reinforced epoxy hybrid composites. Int. J. Polym. Anal. Charact. [Internet] 25(4), 238–251 (2020). https://doi.org/10.1080/1023666X.2020.1781481
A. Wong, L.H. Mark, M.M. Hasan, C.B. Park, The synergy of supercritical CO2and supercritical N2in foaming of polystyrene for cell nucleation. J. Supercrit. Fluids [Internet] 90, 35–43 (2014). https://doi.org/10.1016/j.supflu.2014.03.001
R. Yahaya, S.M. Sapuan, M. Jawaid, Z. Leman, E.S. Zainudin, Effect of fiber orientations on the mechanical properties of kenaf–aramid hybrid composites for spall-liner application. Def. Technol. [Internet] 12(1), 52–58 (2016). https://doi.org/10.1016/j.dt.2015.08.005
M.I. Yusuff, N. Sarifuddin, Z. Ahmad, Mechanical properties of woven carbon fiber/kenaf fabric reinforced epoxy matrix hybrid composites. Malays. J. Microsc. 15(1), 10–16 (2019)
Acknowledgments
The authors would like to thank the following granting foundations. FM Monticeli (FAPESP); RM Neves (CAPES); JHS Almeida Jr. (CAPES); and HL Ornaghi Jr. (CNPq Process number 151438/2020-0).
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 Springer Nature Singapore Pte Ltd.
About this entry
Cite this entry
Monticeli, F.M., Neves, R.M., Almeida, J.H.S., Ornaghi, H.L. (2022). Microscopic Analysis of Hybrid Synthetic/Vegetable Fiber-Reinforced Epoxy Composites. In: Mavinkere Rangappa, S., Parameswaranpillai, J., Siengchin, S., Thomas, S. (eds) Handbook of Epoxy/Fiber Composites . Springer, Singapore. https://doi.org/10.1007/978-981-19-3603-6_38
Download citation
DOI: https://doi.org/10.1007/978-981-19-3603-6_38
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-19-3602-9
Online ISBN: 978-981-19-3603-6
eBook Packages: Chemistry and Materials ScienceReference Module Physical and Materials ScienceReference Module Chemistry, Materials and Physics