Abstract
The purpose of this paper is to explore the influence of particle shape on the mechanical behaviors of granular materials using the discrete element method (DEM). Particles with random polygonal shapes were generated using ‘clumps’ (groups of circular particles). The relationships between the particle-scale parameters and the macroscopic responses of granular materials were identified by simulating the biaxial compression tests on numerical samples. The effects of particle shape on the shear strength and deformation of granular materials were analyzed. The micromechanics of the macroscopic responses were investigated through a variety of mechanism demonstrations and micromechanical analysis .
Access provided by CONRICYT-eBooks. Download conference paper PDF
Similar content being viewed by others
Keywords
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.
1 Introduction
Granular materials such as sand, gravel, ballast, rockfill, consist of a mixture particles with different sizes and different shapes. Previous studies [1, 4, 10, 16, 20] have shown that particle shape has significant influences on the macro-mechanical behavior of granular materials. The underlying mechanism results from the particle level interactions which are mainly affected by particle shape.
The discrete element method (DEM ), which was pioneered by Cundall and Strack [6], has been applied in the research fields of granular materials and accepted as an excellent approach to investigate both the macro-mechanical behavior and the underlying micro-mechanism of granular materials . However, the particle shape cannot be reproduced in DEM environment directly as the base element is disk (2D situation) or sphere (3D situation) in the early DEM models. In order to investigate the particle shape effect on the constitutive behaviors of granular materials using DEM, several methods have been proposed to approximate the real particle shapes. An agglomerate of discs or spheres (overlapping and non-overlapping) was introduced to model the irregular particle shapes [5, 7, 8, 12, 13, 17, 18, 19]. In addition, non-spherical base elements such as polygon-shaped elements [2, 3], ellipse-shaped elements [9, 14, 15] were developed to introduce the particle shape effect. However, the simulation of real particle shapes requires a mass of discs or spheres, which may significantly decrease the computation efficiency. The irregular particle shapes are also hard to be considered in large scale analysis , at least with present available computational facility. In addition, ellipse-shaped elements and polygonal elements used in previous literatures cannot reflect the randomness of the real particle shapes.
In this paper, a novel method is proposed to simulate the complex shape of granular materials in the frame of polygonal shape under DEM environment. The generation of random polygon-shaped particle is first briefly introduced. Then a series of biaxial compression tests are conducted. The particle shape effects on the mechanical behaviors of granular materials, including the shear strength, volume strain, and peak friction angle are discussed. Lastly, conclusions and remarks are provided to guide further studies.
2 Modeling Method of Particle Shape
In previous studies the particle shape was generally simulated by polygonal or elliptical elements, which can represent the real particle shape on some degree (e.g. [2, 3, 14]). In this paper the particle shape is generated under the frame of polygonal shape.
The polygonal shape is generated by randomly selecting points on the circle before lining the adjacent two points along a counter-clockwise direction (see Fig. 1). This process abides by an algorithm that forms a convex polygon from the randomly selected points. Polar coordinate is used to determine the position of each vertex based on the local coordinate of the circle as follows:
where \(\theta_{k}\) is the angle corresponding to the kth edge, \(b_{k}\) and \(\delta\) are random number in the interval [0, 1], n is the total number of edges of a polygon. As the introduction of \(b_{k}\) and \(\delta\), the sum of \(\theta_{k}\) may not equal to \(2\pi\), \(\theta_{k}\) should be corrected to make the polygon closed. The correction equation is described as follows:
The coordinate of polygon vertex is determined as follows:
where \(\left( {x_{0} ,y_{0} } \right)\) is the center coordinate of the circle in global Cartesian Coordinate System, r is the radius of the circle, \(\alpha\) is an original phase angle which can be described as \((\frac{\pi }{2} \times rand)\), where rand is a random value in the range of [0, 1].
A Fish code is written to realize this process based on the initial sample generated in PFC2D. The data of polygonal vertexes is saved as a text file to produce the areas of polygons in Finite Element (FE) environment. After generating the areas of polygons, the meshing technique embedded in ANSYS is applied to mesh the areas with a desired element size. Then the area and the central coordinate of each element are calculated and the information of the corresponding disk with the same area and central coordinate is outputted to a text file. Lastly, the text file is inputted into PFC2D and the clumps composed of overlapping discs are created by grouping the balls within the same surface of the irregularly shaped particle. The generation process is shown as Fig. 2. Figure 3 shows the randomly generated polygon with different number of edges. It is obvious that polygonal particle with more edges is much closer to a disk.
As the center of each disk is seated on the mass centroid of each corresponding element and the disk has same area with the replaced element, the total mass is unchanged after the replacement as well as the particle inertia. This method can avoid the particle inertia problem mentioned by Ferellec and McDowell [7].
3 Biaxial Compression Simulation Tests
3.1 Generation of Samples
A series of biaxial compression simulations were implemented in PFC2D environment. The polygonal particle generating method mentioned above was used to generate particles with different shapes. Samples with a desired porosity were generated in a space with 600 mm height and 300 mm width. All samples were isotropically compressed with a servomechanism to a confining pressure of 0.8 MPa before biaxial shearing. All the compression tests were carried out under a gravity-free environment. The input parameters are listed in Table 1. A uniform particle size distribution was used with the particle diameter ranges from 10 to 20 mm. The number of polygon edges, n, was used as a shape descriptor (as shown in Fig. 3) and the element size used was 0.003 m.
Three kinds of polygon with different edges (i.e., n = 4, 6, 8) and a perfect disk were used to generate four different samples with an initial porosity of 17 % (Fig. 4). The area conversion ratio \(\alpha = A_{aim} /A_{orig}\), was introduced to describe the overall sphericity of the desired sample (e.g. Figure 2d) compared with that of the original sample (e.g. Figure 2a). \(A_{aim}\) and \(A_{orig}\) are the total area of the particles of desired sample and the total area of the particles of original sample, respectively. Apparently, \(\alpha\) increases with the increasing number of polygon edges. The maxima of \(\alpha\), i.e. 1, can be obtained when the sample is composed of ideal circular particle (see Fig. 4d). The parameters of numerical samples with different-shaped particles were shown in Table 2.
3.2 Results and Discussions
The deviatoric stress versus axial strain and volumetric strain versus axial strain curves of different samples were monitored during the tests and shown in Fig. 5.
The peak deviatoric stress decreased with the increasing number of polygonal edges (see Fig. 5a). This was consistent with the conclusion of [11] that particles with more angular shape cause an increase in shear strength. The peak deviatoric stresses and peak friction angles of different samples obtained from the simulation results were shown in Fig. 6. The volumetric stain variation of different samples (see Fig. 5b) reflected the particle shape effect as well. For S-4, the sample behaved a strong shear contraction as the circular particles have no rolling resistance. For samples with shaped particles, the more angular the particle shape was, the larger shear contraction and shear dilatancy can be mobilized.
4 Conclusions
A novel polygonal particle shape generating method for DEM using the meshing technique embedded in ANSYS and overlapping discs has been developed. The method can produce irregular particle shape randomly under the frame of polygonal shape. The particle inertia of irregularly shaped particles generated in DEM environment is same as original particle inertia. Particle shape effects on the mechanical behavior of granular materials were investigated based on this method. The numerical results match the finding of Matsushima and Saomoto [11] very well. This method provides a feasible way to study the particle shape effects on granular materials. In the proposed numerical simulation, complex particle shape was not considered as well as the particle breakage. The other kind of simplified particle shape and particle breakage will be discussed in subsequent papers.
References
Abbireddy, C.O.R., Clayton, C.R.I.: The impact of particle form on the packing and shear behaviour of some granular materials: an experimental study. Granul. Matter 17(4), 427–438 (2015)
Alonso-Marroquin, F., Luding, S., Herrmann, H.J., Vardoulakis, I.: Role of anisotropy in the elastoplastic response of a polygonal packing. Phys. Rev. E 71(5), 051304 (2005)
Azéma, E., Radjai, F., Peyroux, R., Saussine, G.: Force transmission in a packing of pentagonal particles. Phys. Rev. E 76(1), 011301 (2007)
Cho, G.C., Dodds, J., Santamarina, J.C.: Particle shape effects on packing density, stiffness, and strength: natural and crushed sands. J. Geotech. Geoenviron. Eng. 132(5), 591–602 (2006)
Cil, M.B., Alshibli, K.A.: Modeling the influence of particle morphology on the fracture behavior of silica sand using a 3D discrete element method. C.R. Méc. 343(2), 133–142 (2015)
Cundall, P.A., Strack, O.D.L.: A discrete numerical model for granular assemblies. Geotechnique 29(1), 47–65 (1979)
Ferellec, J.F., McDowell, G.R.: A method to model realistic particle shape and inertia in DEM. Granul. Matter 12(5), 459–467 (2010)
Katagiri, J., Matsushima, T., Yamada, Y.: Simple shear simulation of 3D irregularly-shaped particles by image-based DEM. Granul. Matter 12(5), 491–497 (2010)
Lin, X., Ng, T.T.: A three-dimensional discrete element model using arrays of ellipsoids. Geotechnique 47(2), 319–329 (1997)
Lu, M., McDowell, G.R.: The importance of modelling ballast particle shape in the discrete element method. Granul. Matter 9(1–2), 69–80 (2007)
Matsushima, T., Saomoto, H.: Discrete element modeling for irregularly-shaped sand grains. In: Mestat (ed.) Proceedings of NUMGE2002: Numerical Methods in Geotechnical Engineering, pp. 239–246 (2002)
Matsushima, T., Katagiri, J., Uesugi, K., Tsuchiyama, A., Nakano, T.: 3D shape characterization and image-based DEM simulation of the lunar soil simulant FJS-1. J. Aerosp. Eng. 22(1), 15–23 (2009). doi:10.1061/(ASCE)0893-1321
Mollon, G., Zhao, J.: Characterization of fluctuations in granular hopper flow. Granul. Matter 15(6), 827–840 (2013)
Ng, T.T.: Particle shape effect on macro-and micro-behaviors of monodisperse ellipsoids. Int. J. Numer. Anal. Meth. Geomech. 33(4), 511–527 (2009)
Ouadfel, H., Rothenburg, L.: Stress–force–fabric’relationship for assemblies of ellipsoids. Mech. Mater. 33(4), 201–221 (2001)
Santamarina, J.C., Cho, G.C.: Soil behaviour: the role of particle shape. In: Advances in Geotechnical Engineering: The Skempton Conference, vol. 1, pp. 604–617. Thomas Telford (2004, March)
Shi, C., Li, D.J., Xu, W.Y., Wang, R.: Discrete element cluster modeling of complex mesoscopic particles for use with the particle flow code method. Granul. Matter 17(3), 377–387 (2015)
Stahl, M., Konietzky, H.: Discrete element simulation of ballast and gravel under special consideration of grain-shape, grain-size and relative density. Granul. Matter 13(4), 417–428 (2011)
Thomas, P.A., Bray, J.D.: Capturing nonspherical shape of granular media with disk clusters. J. Geotech. Geoenviron. Eng. 125(3), 169–178 (1999)
Ting, J.M., Meachum, L., Rowell, J.D.: Effect of particle shape on the strength and deformation mechanisms of ellipse-shaped granular assemblages. Eng. Comput. 12(2), 99–108 (1995)
Acknowledgments
This work is supported by the National Natural Science Foundation of China (Grant No. 51379161 and 51322905).
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2017 Springer Science+Business Media Singapore
About this paper
Cite this paper
Zhou, W., Xu, K., Yang, L., Ma, G. (2017). Influence of Particle Shape on Mechanical Behavior of Granular Materials. In: Li, X., Feng, Y., Mustoe, G. (eds) Proceedings of the 7th International Conference on Discrete Element Methods. DEM 2016. Springer Proceedings in Physics, vol 188. Springer, Singapore. https://doi.org/10.1007/978-981-10-1926-5_28
Download citation
DOI: https://doi.org/10.1007/978-981-10-1926-5_28
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-10-1925-8
Online ISBN: 978-981-10-1926-5
eBook Packages: Physics and AstronomyPhysics and Astronomy (R0)