Abstract
This chapter proposes a novel smart fuzzy control algorithm for mitigation of dynamic responses of seismically excited bridge structures equipped with control devices. The smart fuzzy controller is developed through the combination of discrete wavelet transform, backpropagation neural networks, and Takagi-Sugeno fuzzy model. To demonstrate the effectiveness of the proposed smart fuzzy controller, it is tested on a highway bridge equipped with magneto rheological (MR) dampers. It controls the smart dampers installed on the abutments of the highway bridge structure. The 1940 El-Centro and Kobe earthquakes are used as disturbance signals. It is demonstrated that the smart fuzzy controller is effective in reducing the structural responses of the highway bridge under a variety of seismic excitations.
Access provided by CONRICYT-eBooks. Download chapter PDF
Similar content being viewed by others
Keywords
1 Introduction
In recent years, smart control strategies have attracted a great deal of attention from the structural engineering community [39, 3, 4, 5, 6, 10, 28, 29, 31]. However, a difficult problem in dealing with smart structures is creating an effective control model for a nonlinear dynamic structure under a variety of environmental forces [21, 23–26, 37, 6, 15]. Nonlinear systems occur when highly nonlinear hysteretic dampers, such as the magnetorheological (MR) dampers, are implemented into a structure to aid in the structure’s ability to withstand the destructive environmental forces such as strong winds and earthquake loads [36]. Being able to mathematically model the structure-nonlinear damping system and its corresponding controller is a challenging task in smart control. Therefore, the challenge is to create a mathematical model to develop a relationship between the input and output of a smart structure that uses a nonlinear damping device. This chapter proposes a new smart control system for reducing nonlinear behavior of a seismically excited highway bridge structure with smart dampers.
The development of an effective smart control algorithm is essential in smart structures to operate the smart dampers within large civil structures. The goals of an effective smart controller is to reliably control how a system will behave under a variety of dynamic loading scenarios such as far- and near-field earthquakes, considering interactions between the structure and the smart dampers. Smart control algorithms can be separated into two categories: model-based and model-free algorithms [25]. The model-based control methods use the structural properties of the system, including stiffness and damping systems that are intrinsically imbedded in the structure and its materials [7, 8]. The model-free control approaches are implemented through training data to the input-output map of the structure employing the smart dampers [37, 38]. This model-free approach is useful to bridge the gap between the linear and nonlinear parts of the smart system. This has successfully been done with neural networks as well as fuzzy logic systems. In particular, the incorporation of the two systems provides a better learning model to use for training the model-free control models.
In this chapter, a new smart control model is developed through the integration of best features of discrete wavelet transform (WT), and fuzzy logic theory and neural network (NN). The first model used as a part of the proposed system in this chapter is a rule-based fuzzy logic. The fuzzy logic model has the main advantage of being used as a nonparametric method for system identification and control system design, and has been researched previously [44, 40, 21, 22, 27–33, 35], as well as general studies into the uncertainties and complexities of the dynamic system [34, 23]. Using a Takagi-Sugeno (TS) model for fuzzy logic theory allows for a representation of nonlinear systems using fuzzy rules and local linear models [40, 19, 41, 12, 20, 9, 11, 23, 42]. A disadvantage of using fuzzy inference systems as a control model is that it needs a time consuming optimization process of the parameters. The optimization process can be very complex, leading itself to the inclusion of NNs. The use of a NN is to develop a learning mechanism that emulates that of the human brain, such that it creates a network of interlinked nodes. These nodes, being connected, compute an output from the input to the node, and create a series of links between all nodes. As mentioned previously, the use of a fuzzy inference system can be complex and difficult in computations. Using a NN in combination with a fuzzy inference system can create a model that is more efficient. The NN adjusts parameters throughout the entirety of computation. The regulated parameters improve performance and decreases errors of the system. It is able to learn patterns and make adjustments as needed to further create a more improved model because it emulates the human brain and its cognitive mechanism. It has been studied previously to create a full model structure [16].
However, due to the complexities of training the using NNs, computation time can become excessive. Therefore, wavelet transform (WT) is used in conjunction with the combined fuzzy inference system, and NNs to compress input data and decrease computation time. WTs, combined with the neuro-fuzzy (NF) model, leads to a wavelet-based NF model (WNF). The WT can be used to filter out high or low frequency components from a time series. The WT improves upon previous methods due to its ability to incorporate an adjustable window function. It allows a user to analyze particular data points in a time series, rather than the entire time window, which is the case in Fourier transforms. Fast Fourier transforms (FFT) have been used previously for damage detection, system identification, and control systems, but require a fixed time-window for the entire data set [14]. This limitation of the FFT can induce difficulty when analyzing data for long periods of time, as in the case of real-time structural control, and can lead to missing key components, such as a particular control frequency. The WT allows for an adjustable window, and therefore is able to look into any portion of a time series. WTs can also be used as a means of filtering, which is critical in the use of the WNF control model. As previously mentioned, the NF system requires high computation time due to the stochastic learning mechanism of the NNs. Being able to decrease the amount of data points while still maintaining the important components allows for a reduced computational cost. The proposed model uses two levels of discrete WTs for compressing input data. Note that fuzzy logic controllers [2] and neuro-fuzzy controllers [13] have been widely researched previously. However, these controllers need extensive computation time to achieve adequate performance. Therefore, the creation of the new WNF system provides for decreased computation times while maintaining the performance. Thus, the creation of the WNF system for means of smart control algorithm is innovative in its application to smart damping systems for mitigation of responses of highway bridge structures.
2 Smart Highway Bridge Systems
2.1 Highway Bridge
To facilitate research in structural control, a benchmark bridge was developed based on an existing structure located at the crossing of the 91 and 5 highways in Orange County of California, USA [1]. A prestressed concrete box-girder is used with the span of 58.5 m. The deck has a width of 12.95 and 15 m for the east and west spans, respectively. The bridge carries four lanes of traffic atop columns of 6.9 m in height. The location of the bridge is within 20 km of two faults, the Whittier-Ellsinore and Newport-Inglewood fault zones, showing a great need for structural control due to its susceptibility to seismic events. Figure 1 shows the bridge schematic.
2.2 Magnetorheological (MR) Dampers
In recent years, smart structures have emerged from many engineering fields because the performance of structural systems can be improved without either significantly increasing the structure mass or requiring high cost of control power. They may be called intelligent structures, adaptive structures, active structures, and the related technologies adaptronics, structronics, etc. The reason to use these terminologies is that a smart structure is an integration of actuators, sensors, control units, and signal processing units with a structural system. The materials that are commonly used to implement the smart structure: piezoelectrics, shape memory alloys, electrostrictive, magnetostrictive materials, polymer gels, magnetorheological fluid, etc., researched in detail by Hurlebaus and Gaul [17].
Semiactive control systems have been applied to large structures because the semiactive control strategies combine favorable features of both active and passive control systems. Semiactive control devices include variable-orifice dampers, variable-stiffness devices, variable-friction dampers, controllable-fluid dampers, shape memory alloy actuators, piezoelectrics, etc., as described by Hurlebaus and Gaul [17]. In particular, one of the controllable-fluid dampers, magnetorheological (MR) damper has attracted attention in recent years because it has many attractive characteristics.
In general, a MR damper consists of a hydraulic cylinder, magnetic coils, and MR fluids that consist of micron-sized magnetically polarizable particles floating within oil-type fluids as shown in Fig. 2.
The MR damper is operated as a passive damper; however, when a magnetic field is applied to the MR fluids, the MR fluids are changed into a semi-solid state in a few milliseconds. This is one of the most unique aspects of the MR damper compared to active systems: the active control system malfunction might occur if some control feedback components, e.g., wires and sensors, are broken for some reasons during a severe earthquake event; while a semiactive system is still operational as at least a passive damping system even when the control feedback components are not functioning properly. Its characteristics are summarized by Kim et al. [23].
2.3 Smart Controller
In 1985, Takagi and Sugeno suggested an effective way for modeling complex nonlinear systems by introducing linear equations in consequent parts of a fuzzy model. It has led to reduction of computational cost because it does not need any defuzzification procedure. The fuzzy system used in the WNF model is of the form [22].
where R j is the jth fuzzy rule, N j is the number of fuzzy rules, \(P_{ij}\) are fuzzy sets centered at the jth operating point, and \(u_{FZ}^{i}\) are premise variables that can be either input or output values. The equation of the consequent part \(z = f(u_{FZ}^{1} , \ldots ,u_{FZ}^{i} )\) can be any linear equation. Using fuzzy interpolation methods, all of the local subsystems are integrated
where \(W_{j} (u_{FZ}^{i} ) = \prod\nolimits_{i = 1}^{n} {} \mu_{{p_{i,j} }} (u_{FZ}^{i} )\), n is the number of input variables and \(\mu_{{p_{i,j} }} (u_{FZ}^{i} )\) is the membership grade of \(u_{FZ}^{i}\) in \(P_{i,j}\). However, the main challenge in using a fuzzy model is the optimization of its parameters. Therefore, incorporating NNs to create a neuro-fuzzy system allows for these parameters to be optimized during computation.
The architecture of a NF model is shown in Fig. 3. This figure represents a two inputs, one output, and three membership functions (MFs). Each layer has particular tasks to complete before the data moves to the next layer.
In layer 1, the function of the node is represented by
For a Gaussian MF used in this simulation,
where \(a_{1}\) and \(a_{2}\) are adjustable parameters of the Gaussian function. This MF is applied to each input in layer 1. Layer 2 then outputs the product of all inputs into layer 2, known as the firing strength
Layer 3 takes a ratio of these layer 2 firing strengths in order to normalize the layer 2 outputs, such that
Layer 4 then applies a node function to the normalized firing strengths
The last layer summates the layer inputs
The output of this NF system is then used in a hybrid learning algorithm to create a linear combination of the consequent parameters. The key parameters for this simulation include the number of iterations, or epochs, the number of MFs and the type of MF, as well as the step size of the function. In this study, the premise part is determined by backpropagation algorithm while the consequent parameters are optimized using the least square estimator. Four Gaussian membership functions are adopted, the number of iterations is 300, the iteration step size is 0.9 and the increase rate of the step size is 1.2. Types of MFs can vary from a generalized bell function, Gaussian functions, sigmoidal functions, trapezoidal function, as well as other forms. Each change of variables will yield different output results [18, 43]. The fuzzy inference system sets up rules based on the number of MFs used in simulation. Fuzzy rules are set up for a five MF system. Each number represents one of the twenty-five fuzzy regions that are created through the use of five MFs in the neuro-fuzzy model. The fuzzy region is defined by the premise, and the output is generated through the consequent.
The inclusion of discrete wavelet transforms allows for an effective method to rid the control system of extraneous data, or noise. This methodology uses Daubechie wavelets filters in order to de-noise response data that are then used as inputs to the smart fuzzy control model. As mentioned earlier, the use of discrete wavelet transforms allows for a fixed time-frequency resolution. It means that the window function is chosen, and then the resolution is fixed through processing. A reduction in the number of data points required for accurate representation of the system is possible due to representation of the function with several discretization steps. The proposed algorithm for the smart fuzzy control is shown in Fig. 4.
This control model proposes the use of two levels of discrete wavelet transform as a means of filtering as well as training the optimal control force. The architecture of this proposed smart fuzzy control system is depicted in Fig. 5. The smart fuzzy control algorithm is a two-input, one-output system to determine the control force of an MR damper. For this study, the inputs to the smart fuzzy control system are displacement and acceleration measurements. These were determined through an iterative process to maximize the results from training of the smart fuzzy control system, where velocity and drift responses were also studied to find the combination with the most favorable results. Next, simulations were performed on a highway bridge under a variety of earthquake loads to successfully reduce the seismic responses.
2.4 Simulation
Many simulations were performed to determine the best arrangement of control forces. It was found that the computation of only two control forces would need to be calculated for optimal voltage signals: x-direction and y-direction. This bridge is equipped with sixteen MR dampers in each x- and y-directions; all the MR dampers in each direction are commanded by a single control signal. To train the input-output mapping function of the smart fuzzy control model, an artificial earthquake signal that includes characteristics of the 1940 El-Centro and Kobe earthquake, as shown in Figs. 6 and 7.
Figures 8, 9, 10, 11, 12 and 13 show the simulation results. Figures 8 and 9 are the relative displacement responses to the 1940 El-Centro and Kobe earthquakes, respectively. Figures 10 and 11 are the absolute acceleration responses to the 1940 El-Centro and Kobe earthquakes, respectively. Figures 12 and 13 are the base shear forces at the column to the 1940 El-Centro and Kobe earthquakes, respectively. The dotted lines represent the uncontrolled responses; while the solid red lines are the responses of the smart fuzzy control systems. As shown in figures, the proposed smart fuzzy control system is effective in mitigating the dynamic responses of highway bridge structures for most cases.
As a means of validation and comparison, several evaluation indices are used. These indices compare structural responses and control outputs of the proposed smart control system to that of the uncontrolled structure, showing how much each index is reduced [1].
here \(\hat{F}_{bi} (t)\) is the time history of shear force of the ith degree of freedom of the control system, \(\hat{F}_{0b,\hbox{max} }\) is the maximum shear force of the uncontrolled structure, \(M_{bi} (t)\) is the time history of overturning moment, \(M_{0b,\hbox{max} }\) is the maximum overturning moment of the uncontrolled structure, \(\hat{y}_{mi} (t)\) is the time history of the midspan displacement, \(\hat{y}_{0m,\hbox{max} } (t)\) is the maximum midspan displacement of the uncontrolled structure, \(\left| {\ddot{\hat{y}}_{mi} (t)} \right|\) is the time history of the midspan acceleration, \(\ddot{\hat{y}}_{0m,\hbox{max} } (t)\) is the maximum acceleration of the uncontrolled structure, \(\hat{y}_{bi} (t)\) is the time history of the abutment displacement, \(\hat{y}_{0b,\hbox{max} }\) is the maximum abutment displacement of the uncontrolled structure, \({\hat{\Phi }}_{i} (t)\) is the time history of the ductility, \({\hat{\Phi }}_{\hbox{max} }\) is the maximum ductility of the uncontrolled structure, \(d\hat{E}_{i}\) is the dissipated energy of curvature at the column, \(\hat{E}_{\hbox{max} }\) is the maximum dissipated energy of the curvature at the column of the uncontrolled structure, \(\hat{N}_{c,d}\) is the number of plastic connections of the control system, \(\hat{N}_{d}\) is the number of plastic connections of the uncontrolled system, \(\left| . \right|\) denotes the absolute value, \(\left\| . \right\|\) denotes the normalized value, \(\hat{f}_{l} (t)\) is the time history of the control force from the control device, \(\hat{W}\) is the seismic weight of the system, \(\hat{d}_{l} (t)\) is the stroke of the control device, \(x_{0m,\hbox{max} }\) is the maximum bearing deformation of the uncontrolled system, \(\hat{P}_{l} (t)\) is the time history of the instantaneous power required for the control device, \(\dot{\hat{x}}_{0m,\hbox{max} }\) is the maximum velocity of bearing of the uncontrolled system, and \(\hat{x}_{c,k}\) is the discrete state vector for the control algorithm. Table 1 shows the evaluation results of the proposed smart control systems. It is observed from Table 1 that the “Max” peak response quantities using the smart controller are quite effective in reducing structural vibration to both the El-Centro and Kobe earthquakes. In particular, peak evaluation criteria J 2, J 3, J 5 ~ J 11, and J 13, J 14, J 16 and J 18 are significantly reduced during both ground motions. It should be noted that structural displacement responses are directly related to safety of the bridge structures.
3 Conclusion
In this chapter, a novel smart control system is proposed for seismic response controls of seismically-excited bridge structures employing magnetorheological (MR) dampers. The smart control system is an integrated model of Takagi-Sugeno fuzzy model, wavelet transforms, and artificial neural networks. Using the smart fuzzy control system combines the positive attributes of the three described methodologies to create a system that is believed to yield more efficient results for system control of smart structures and shorter training times. To train the input–output mapping function of the smart fuzzy control model, an artificial earthquake signal and an MR damper force signal are used as a disturbance input signal and a control input, respectively, while acceleration response is used as output data. It is demonstrated from the simulation that the proposed smart fuzzy control model is effective in reducing the behavior of the seismically excited bridge-MR damper system.
References
Agrawal A, Tan P, Nagarajaiah S, Zhang J (2009) Benchmark structural control problem for a seismically excited highway bridge—Part I: Phase I problem definition. Struct Control Health Monit 16:509–529
Ahlawat AS, Ramaswamy A (2002) Multi objective optimal design of FLC driven hybrid mass damper for seismically excited structures. Earthquake Eng Struct Dynam 31:1459–1479
Arsava SK, Kim Y, El-Korchi T, Park HS (2013) Nonlinear system identification of smart structures under high impact loads. J Smart Mater Struc 22. doi:10.1088/0964-1726/22/5/055008
Arsava SK, Chong JW, Kim Y (2014) A novel health monitoring scheme for smart structures. J Vib Control. doi:10.1177/1077546314533716
Arsava SK, Nam Y, Kim Y (2015) Nonlinear system identification of smart reinforced concrete structures under high impact loads. J Vib Control. doi:10.1177/1077546314563966
Arsava SK, Kim Y, Kim KH, Shin BS (2015) Smart fuzzy control of reinforced concrete structures excited by collision-type forces. Expert Syst Appl 42(21):7929–7941
Cha YJ, Agrawal AK, Kim Y, Raich A (2012) Multi-objective genetic algorithms for cost-effective distributions of actuators and sensors in large structures. Expert Syst Appl 39:7822–7833
Cha YJ, Kim Y, Raich A, Agrawal AK (2013) Multi-objective optimization for actuator and sensor layouts of actively controlled 3D buildings. J Vib Control 19:942–960
Chen Y, Yang B, Abraham A, Peng L (2007) Automatic design of hierarchical Takagi-Sugeno Type fuzzy systems using evolutionary algorithms. IEEE Trans Fuzzy Syst 15:385–397
Chong JW, Kim Y, Chon K (2014) Nonlinear multiclass support vector machine-based health monitoring system for buildings employing magnetorheological dampers. J Intell Mater Syst Struct 25:1456–1468
Du H, Zhang N (2008) Application of evolving Takagi-Sugeno Fuzzy Model to nonlinear system identification. Appl Soft Comput 8:676–686
Faravelli L, Yao T (1996) Use of adaptive networks in fuzzy control of civil structures. Microcomput Civil Eng 12:67–76
Gu Z, Oyadiji S (2008) Application of MR damper in structural control using ANFIS Method. Comput Struct 86:427–436
Gurley K, Kareem A (1999) Applications of wavelet transforms in earthquake, wind and ocean engineering. Eng Struct 21:149–167
Hughes JE, Kim Y, El-Korchi T (2015) Radar technology for structural hazard mitigation. J Vib Control
Hung SL, Huang CS, Wen CM, Hsu YC (2003) Nonparametric identification of a building structure from experimental data using wavelet neural network. Computer-Aided Civil Infrastruct Eng 18:356–368
Hurlebaus S, Gaul L (2006) Smart structure dynamics. Mech Syst Signal Process 20:255–286
Jang JSR (1993) ANFIS: adaptive-network-based fuzzy inference system. IEEE Trans Syst Man Cybern 23:665–685
Johansen TA (1994) Fuzzy model based control: stability, robustness, and performance issues. IEEE Trans Fuzzy Syst 2:221–234
Johansen TA, Babuška R (2003) Multiobjective identification of Takagi-Sugeno fuzzy models. IEEE Trans Fuzzy Syst 11:847–860
Kim Y, Langari R (2007) Nonlinear identification and control of a building structure with a magnetorheological damper system. American control conference, New York
Kim Y, Hurlebaus S, Sharifi R, Langari R (2009a) Nonlinear identification of MIMO smart structures. ASME dynamic systems and control conference, Hollywood, California
Kim Y, Langari R, Hurlebaus S (2009) Semiactive nonlinear control of a building using a magnetorheological damper system. Mech Syst Signal Process 23:300–315
Kim Y, Hurlebaus S, Langari R (2010) Control of a seismically excited benchmark building using linear matrix inequality-based semiactive nonlinear fuzzy control. ASCE J Struct Eng 136(8):1023–1026
Kim Y, Langari R, Hurlebaus S (2010) Model-based multi-input, multi-output supervisory semiactive nonlinear fuzzy controller. Computer-Aided Civil Infrastruct Eng 25:387–393
Kim Y, Kim C, Langari R (2010) Novel bio-inspired smart control for hazard mitigation of civil structures. J Smart Mater Struct 19:115009. doi:10.1088/0964-1726/19/11/115009
Kim Y, Hurlebaus S, Langari R (2011) Fuzzy identification of building-MR damper system. Int J Intell Fuzzy Syst 22(4):185–205
Kim Y, Chong JW, Chon K, Kim JM (2013) Wavelet-based AR-SVM for health monitoring of smart structures. J Smart Mater Struct 22(1):015003. doi:10.1088/0964-1726/22/1/015003
Kim Y, Mallick R, Bhowmick S, Chen B (2013) Nonlinear system identification of large-scale smart pavement systems. Expert Syst Appl 40:3551–3560
Kim Y, Kim KH, Shin BS (2014) Fuzzy model forecasting of offshore bar-shape profiles under high waves. Expert Syst Appl 41:5771–5779
Kim Y, Bai JW, Albano LD (2014) Fragility estimates of smart structures with sensor faults. J Smart Mater Struct 22:125012. doi:10.1088/0964-1726/22/12/125012
Kim Y, Shin SS, Plummer JD (2014) A wavelet-based autoregressive fuzzy model for forecasting algal blooms. Environ Model Softw 62:1–10
Kim Y, Kim YH, Lee S (2015) Multivariable nonlinear identification of smart buildings. Mech Syst Signal Process 62–63:254–271
Langari R (1999) Past, present and future of fuzzy control: a case for application of fuzzy logic in hierarchical control. In: Proceedings, 18th international conference of the north american fuzzy information processing society-NAFIPS, New York City, New York, USA, pp 760–765
Mohammadzadeh S, Kim Y, Ahn J (2015) PCA-based neuro-fuzzy model for system identification of smart structures. J Smart Struct Syst 15(4):1139–1158
Mitchell R, Kim Y, El-Korchi T (2012) System identification of smart structures using a wavelet neuro-fuzzy model. J Smart Mater Struct 21. doi:10.1088/0964-1726/21/11/115009
Mitchell R, Kim Y, El-Korchi T, Cha YJ (2013) Wavelet-neuro-fuzzy control of hybrid building-active tuned mass damper system under seismic excitations. J Vib Control 19(12):1881–1894
Mitchell R, Cha YJ, Kim Y, Mahajan A (2015) Active control of highway bridges subject to a variety of earthquake loads. Earthq Eng Eng Vib 14(2):253–263
Sharifi R, Kim Y, Langari R (2010) Sensor fault isolation and detection of smart structures J Smart Mater Struct 19. doi:10.1088/0964-1726/19/10/105001
Takagi T, Sugeno M (1985) Fuzzy identification of systems and its applications to modeling and control. IEEE Trans Syst Man Cybern 15:116–132
Yager RR, Filev DP (1993) Unified Structure and parameter identification of fuzzy models. IEEE Trans Syst Man Cybern 23:1198–1205
Yan G, Zhou LL (2006) Integrated fuzzy logic and genetic algorithms for multi-objective control of structures using MR dampers. J Sound Vib 296:368–382
Yang YN, Lin S (2005) Identification of parametric variations of structures based on least squares estimation and adaptive tracking technique. ASCE J Eng Mech 131:290–298
Zadeh LA (1965) Fuzzy sets. Inf Control 8:338–353
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2017 Springer International Publishing AG
About this chapter
Cite this chapter
Kim, Y., Mahajan, A.A. (2017). Smart Control of Seismically Excited Highway Bridges. In: Papadrakakis, M., Plevris, V., Lagaros, N. (eds) Computational Methods in Earthquake Engineering. Computational Methods in Applied Sciences, vol 44. Springer, Cham. https://doi.org/10.1007/978-3-319-47798-5_14
Download citation
DOI: https://doi.org/10.1007/978-3-319-47798-5_14
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-47796-1
Online ISBN: 978-3-319-47798-5
eBook Packages: EngineeringEngineering (R0)