Abstract
The article deals with the properties of the Ti-TiN-(Ti,Cr,Al)N multilayer composite coatings with a nanolayer structure of their wear-resistant layers and the nanolayer period λ within a range from 10 to 900 nm. The studies were focused on the coating nanostructures and the influence of the nanolayer period λ on the performance properties of coated cutting tools during the turning of American Iron and Steel Institute (AISI) 420 (230 HB) martensitic stainless steel. The investigation found that the coatings with the nanolayer period λ = 10–25 nm demonstrated the best resistance to the crater formation on the rake face of cutting tools and to flank wear. The highest wear resistance was demonstrated by a coated tool with the nanolayer period λ = 10 nm.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Kalss, W., Reiter, A., Derflinger, V., Gey, C., Endrino, J.L.: Modern coatings in high performance cutting applications. Int. J. Refract. Hard. Met. 24(5), 399–404 (2006)
Bobzin, K.: High-performance coatings for cutting tools. CIRP J. Manuf. Sci. Technol. 18, 1–9 (2017)
Vereschaka, A.S.: Working Capacity of the Cutting Tool with Wear Resistant Coatings. Mashinostroenie, Moscow (1993)
Bouzakis, K.D., Michailidis, N., Skordaris, G., Bouzakis, E., Biermann, D., M’Saoubi, R.: Cutting with coated tools: coating technologies, characterization methods and performance optimization. CIRP Ann. Manuf. Technol. 61, 703–723 (2012)
Tkadletz, M., Schalk, N., Daniel, R., Keckes, J., Czettl, C., Mitterer, C.: Advanced characterization methods for wear resistant hard coatings: a review on recent progress. Surf. Coat. Technol. 285, 31–46 (2016)
Vereschaka, A., et al.: Investigation of the influence of the thickness of nanolayers in wear-resistant layers of Ti-TiN-(Ti,Cr,Al)N coating on destruction in the cutting and wear of carbide cutting tools. Surf. Coat. Technol. 385, 125402 (2020)
Grigoriev, S., et al.: Investigation of multicomponent nanolayer coatings based on nitrides of Cr, Mo, Zr, Nb, and Al. Surf. Coat. Technol. 401, 126258 (2020)
Vereschaka, A.A., Grigoriev, S.N., Sitnikov, N.N., Oganyan, G.V., Batako, A.: Working efficiency of cutting tools with multilayer nano-structured Ti-TiCN-(Ti, Al)CN and Ti-TiCN-(Ti, Al, Cr)CN coatings: analysis of cutting properties, wear mechanism and diffusion processes. Surf. Coat. Technol. 332, 198–213 (2017)
Vereschaka, A., et al.: Investigation of wear dynamics for cutting tools with multilayer composite nanostructured coatings in turning constructional steel. Wear 420–421, 17–37 (2019)
Baker, M.A., Klose, S., Rebholz, C., Leyland, A., Matthews, A.: Evaluating the microstructure and performance of nanocomposite PVD TiAlBN coatings. Surf. Coat. Technol. 151–152, 338–343 (2002)
Singh, J., Wolfe, D.E.: Nanostructured component fabrication by electron beam-physical vapor deposition. J. Mater. Eng. Perform. 14(4), 448–459 (2005)
Kuzin, V., Grigor’ev, S., Volosova, M.: Effect of a TiC coating on the stress-strain state of a plate of a high-density nitride ceramic under nonsteady thermoelastic conditions, Refract. Ind. Ceram. 54, 376–380 (2014)
Skordaris, G., et al.: Brittleness and fatigue effect of mono- and multi-layer PVD films on the cutting performance of coated cemented carbide inserts. CIRP Ann. Manuf. Technol. 63, 93–96 (2014)
Zhang, S., Sun, D., Yongqing, F., Hejun, D.: Recent advances of superhard nanocomposite coatings: a review. Surf. Coat. Technol. 167, 113–119 (2003)
Leyland, A., Matthews, A.: On the significance of the H/E ratio in wear control: a nano-composite coating approach to optimized tribological behavior. Wear 246, 1–11 (2000)
Alexey, V.: Development of assisted filtered cathodic vacuum arc deposition of nano-dispersed multi-layered composite coatings on cutting tools. Key Eng. Mater. 581, 62–67 (2014)
Vereschaka, A.A., et al.: Effect of adhesion and the wear-resistant layer thickness ratio on mechanical and performance properties of ZrN-(Zr, Al, Si)N coatings. Surf. Coat. Technol. 357, 218–234 (2019)
Vereschaka, A., et al.: Effect of adhesion and tribological properties of modified composite nano-structured multi-layer nitride coatings on WC-Co tools life. Tribol. Int. 128, 313–327 (2018)
Vereschaka, A., Tabakov, V., Grigoriev, S., Sitnikov, N., Andreev, N., Milovich, F.: Investigation of wear and diffusion processes on rake faces of carbide inserts with Ti-TiN-(Ti, Al, Si)N composite nanostructured coating. Wear 416–417, 72–80 (2018)
Hovsepian, P., et al.: TiAlN based nanoscale multilayer coatings designed to adapt their tribological properties at elevated temperatures. Thin Solid Films 485, 160–168 (2005)
Antonov, M., Hussainova, I., Sergejev, F., Kulu, P., Gregor, A.: Assessment of gradient and nanogradient PVD coatings behavior under erosive, abrasive and impact wear conditions. Wear 267(5–8), 898–906 (2009)
Vereschaka, A.A., et al.: Nano-scale multi-layered coatings for improved efficiency of ceramic cutting tools. Int. J. Adv. Manuf. Technol. 90(1–-4), 27–43 (2017)
Contreras, E., Galindez, Y., Rodas, M.A., Bejarano, G., Gómez, M.A.: CrVN/TiN nanoscale multilayer coatings deposited by DC unbalanced magnetron sputtering. Surf. Coat. Technol. 332, 214–222 (2017)
Bobzin, K., Brögelmann, T., Kruppe, N.C., Arghavani, M., Mayer, J., Weirich, T.E.: Plastic deformation behavior of nanostructured CrN/AlN multilayer coatings deposited by hybrid dcMS/HPPMS. Surf. Coat. Technol. 332, 253–261 (2017)
Hovsepian, P., Ehiasarian, A.P., Deeming, A., Schimpf, C.: Novel TiAlCN/VCN nanoscale multilayer PVD coatings deposited by the combined high-power impulse magnetron sputtering/unbalanced magnetron sputtering (HIPIMS/UBM) technology. Vacuum 82, 1312–1317 (2008)
Zhang, Z.G., et al.: Microstructures and tribological properties of CrN/ZrN nanoscale multilayer coatings. Appl. Surf. Sci. 255, 4020–4026 (2009)
Araujo, J.A., Araujo, G.M., Souza, R.M., Tschiptschin, A.P.: Effect of periodicity on hardness and scratch resistance of CrN/NbN nanoscale multilayer coating deposited by cathodic arc technique. Wear 330–331, 469–477 (2015)
Araujo, J.A., Giorjão, R.A.R., Bettini, J., Souza, R.M., Tschiptschin, A.P.: Modeling intrinsic residual stresses built-up during growth of nanostructured multilayer NbN/CrN coatings. Surf. Coat. Technol. 308, 264–272 (2016)
Kamath, G., Ehiasarian, A.P., Purandare, Y., Hovsepian, P.: Tribological and oxidation behaviour of TiAlCN/VCN nanoscale multilayer coating deposited by the combined HIPIMS/(HIPIMS-UBM) technique. Surf. Coat. Technol. 205, 2823–2829 (2011)
Hovsepian, P., Ehiasarian, A.P., Braun, R., Walker, J., Du, H.: Novel CrAlYN/CrN nanoscale multilayer PVD coatings produced by the combined high power impulse magnetron sputtering/unbalanced magnetron sputtering technique for environmental protection of γ-TiAl alloys. Surf. Coat. Technol. 204, 2702–2708 (2010)
AL-Bukhaiti, M.A., Al-Hatab, K.A., Tillmann, W., Hoffmann, F., Sprute T.: Tribological and mechanical properties of Ti/TiAlN/TiAlCN nanoscalemultilayer PVD coatings deposited on AISI H11 hot work tool steel. Appl. Surf. Sci. 318, 180–190 (2014)
Yanga, Y., Yeob, I., Parkc, S., Oh, Y.: Microstructure and phase forming behavior of chrome based multi-composition nitride coatings with nanolayer structures. Ceram. Int. 40, 11567–11573 (2014)
Wang, M., Toihara, T., Sakurai, M., Kurosaka, W., Miyake, S.: Surface morphology and tribological properties of DC sputtered nanoscale multilayered TiAlN/CNx coatings. Tribol. Int. 73, 36–46 (2014)
Vereshchaka, A.A., Vereshchaka, A.S., Mgaloblishvili, O., Morgan, M.N., Batako, A.D.: Nano-scale multilayered-composite coatings for the cutting tools. Int. J. Adv. Manuf. Technol. 72(1–4), 303–317 (2014)
Fominski, V.Yu., Grigoriev, S.N., Celis, J.P., Romanov, R.I., Oshurko, V.B.: Structure and mechanical properties of W–Se–C/diamond-like carbon and W–Se/diamond-like carbon bi-layer coatings prepared by pulsed laser deposition. Thin Solid Films 520(21), 6476–6483 (2012)
Fominski, V.Yu., Grigoriev, S.N., Gnedovets, A.G., Romanov, R.I.: Pulsed laser deposition of composite Mo-Se-Ni-C coatings using standard and shadow mask configuration. Surf. Coat. Technol. 206(24), 5046–5054 (2012)
Metel, A.S., Grigoriev, S.N., Melnik, Y.A., Prudnikov, V.V.: Glow discharge with electrostatic confinement of electrons in a chamber bombarded by fast electrons. Plasma Phys Rep. 37, 628–637 (2011)
Grigoriev, S.N., Melnik, Y.A., Metel, A.S., Panin, V.V., Prudnikov, V.V.: Broad beam source of fast atoms produced as a result of charge exchange collisions of ions accelerated between two plasmas. Instrum. Exp. Tech. 52, 602–608 (2009)
Grigoriev, S., Melnik, Y., Metel, A.: Broad fast neutral molecule beam sources for industrial-scale beam-assisted deposition. Surf. Coat. Technol. 156(1–3), 44–49 (2002)
Grigoriev, S.N., Melnik, Y.A., Metel, A.S., Panin, V.V.: A compact vapor source of conductive target material sputtered by 3-keV Ions at 0.05-Pa pressure. Instrum. Exp. Tech. 52, 731–737 (2009)
Metel, A.S., Grigoriev, S.N., Melnik, Y.A., Bolbukov, V.P.: Broad beam sources of fast molecules with segmented cold cathodes and emissive grids. Instrum. Exp. Tech. 55, 122–130 (2012)
Grigoriev, S.N., Metel’, A.S., Fedorov, S.V.: Modification of the structure and properties of high-speed steel by combined vacuum-plasma treatment. Met. Sci. Heat Treat. 54(1–2), 8–12 (2012)
Grigoriev, S., Metel, A.: Plasma- and beam- assisted deposition methods. Nato Sci. Ser. II Math. Phys. Chem. 155, 147–154 (2004)
Vereschaka, A.A., Grigoriev, S.N., Vereschaka, A.S., Popov, A.Y., Batako, A.D.: Nano-scale multilayered composite coatings for cutting tools operating under heavy cutting conditions. Procedia CIRP 14, 239–244 (2014)
Oliver, W.C., Pharr, G.M.J.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation. J. Mater. Res. 7, 1564–1583 (1992)
Chen, L., Du, Y., Wang, A.J., Wang, S.Q., Zhou, S.Z.: Effect of Al content on microstructure and mechanical properties of Ti-Al-Si-N nanocomposite coatings. Int. J. Refract. Hard. Met. 27(4), 718–721 (2009)
Acknowledgments
The study was supported by a grant from the Russian Science Foundation (project No. 21-19-00612). The study used the equipment from the Centre for collective use of Moscow State Technological University STANKIN (agreement No. 075-15-2021-695, 26/07/2021). The coating structure was investigated using the equipment of the Centre for collective use of scientific equipment “Material Science and Metallurgy”, purchased with the financial support of the Ministry of Science and Higher Education of the Russian Federation (GK 075-15-2021-696).
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Vereschaka, A. et al. (2022). Influence of the Nanostructure Parameters of Wear-Resistant Coatings on the Properties of Carbide Tools. In: Batako, A., Burduk, A., Karyono, K., Chen, X., Wyczółkowski, R. (eds) Advances in Manufacturing Processes, Intelligent Methods and Systems in Production Engineering. GCMM 2021. Lecture Notes in Networks and Systems, vol 335. Springer, Cham. https://doi.org/10.1007/978-3-030-90532-3_11
Download citation
DOI: https://doi.org/10.1007/978-3-030-90532-3_11
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-90531-6
Online ISBN: 978-3-030-90532-3
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)