Abstract
Spray drying is widely used in the food industry to obtain products in the form of powder (Masters 1991; Filková and Mujumdar 1999; Nijdam and Langrish 2005; Roustapour et al. 2006; León et al. 2010). Three types of modes of contact between drying air and the food product can be found: parallel (co-current), counter-current, or mixed (fountain). The latter is a combination of parallel and counter current flow patterns, which implies that the already dry material comes into contact with drops being sprayed, favoring the formation of agglomerates. In turn, the formation of agglomerates raises the rehydration capacity of the final product (Masters 1991; Vega et al. 2001; Peighambardoust et al. 2011). Although spray drying is a common method used for drying thermolabile materials, there are few reports about the dehydrating conditions used for Aloe vera industrial processing. This plant is widely used in the pharmaceutical, cosmetological, and food areas because of the beneficial effects it provides as a functional ingredient in food and cosmetic products (Simal et al. 2000). However, it has been reported that when gel obtained from the Aloe vera leaf is subjected to thermal processing, changes in its components and functional properties, such as wettability, water retention, and oil adsorption capacity, among others, can occur (Eshun and He 2004; García et al. 2010). Aloe gel contains 98.5 % water, and the remaining solid material consists of polysaccharides, fat, and water-soluble vitamins, minerals, enzymes, phenolic compounds, and organic acids (Bozzi et al. 2007; Eshun and He 2004; Hamman 2008). Several studies have focused on assessing the physical, chemical and functional changes caused by Aloe vera gel processing conditions, especially during dehydration through convective drying (Simal et al. 2000; Femenia et al. 2003; Miranda et al. 2009; García et al. 2010; Gulia et al. 2010). However, to date there is limited data regarding the effect that spray drying temperature has on the physical, calorimetric, and functional characteristics of Aloe vera. Therefore, the objective of this study was to evaluate the effect of spray drying temperatures on obtaining Aloe vera gel in powder form.
Access provided by Autonomous University of Puebla. Download chapter PDF
Similar content being viewed by others
Keywords
1 Introduction
Spray drying is widely used in the food industry to obtain products in the form of powder (Masters 1991; Filková and Mujumdar 1999; Nijdam and Langrish 2005; Roustapour et al. 2006; León et al. 2010). Three types of modes of contact between drying air and the food product can be found: parallel (co-current), counter-current, or mixed (fountain). The latter is a combination of parallel and counter current flow patterns, which implies that the already dry material comes into contact with drops being sprayed, favoring the formation of agglomerates. In turn, the formation of agglomerates raises the rehydration capacity of the final product (Masters 1991; Vega et al. 2001; Peighambardoust et al. 2011). Although spray drying is a common method used for drying thermolabile materials, there are few reports about the dehydrating conditions used for Aloe vera industrial processing. This plant is widely used in the pharmaceutical, cosmetological, and food areas because of the beneficial effects it provides as a functional ingredient in food and cosmetic products (Simal et al. 2000). However, it has been reported that when gel obtained from the Aloe vera leaf is subjected to thermal processing, changes in its components and functional properties, such as wettability, water retention, and oil adsorption capacity, among others, can occur (Eshun and He 2004; García et al. 2010). Aloe gel contains 98.5 % water, and the remaining solid material consists of polysaccharides, fat, and water-soluble vitamins, minerals, enzymes, phenolic compounds, and organic acids (Bozzi et al. 2007; Eshun and He 2004; Hamman 2008). Several studies have focused on assessing the physical, chemical and functional changes caused by Aloe vera gel processing conditions, especially during dehydration through convective drying (Simal et al. 2000; Femenia et al. 2003; Miranda et al. 2009; García et al. 2010; Gulia et al. 2010). However, to date there is limited data regarding the effect that spray drying temperature has on the physical, calorimetric, and functional characteristics of Aloe vera. Therefore, the objective of this study was to evaluate the effect of spray drying temperatures on obtaining Aloe vera gel in powder form.
2 Materials and Methods
2.1 Obtaining Aloe vera Powder
Aloe vera gel was obtained from the “Flor de Aloe” Company (Puebla, México), which was filtered for processing in a Mobile Minor 2000 spray dryer (Gea-Niro, Dinamarca) equipped with a dual fluid nozzle in a source-type arrangement and without any addition of drying aid. The inlet (T 1) and outlet (T 2) drying-air temperatures used were 220, 225, and 250 °C and 70, 80, and 90 °C, respectively. The feed stream varied between 1.12 and 1.85 L/h, depending on the desired outlet air temperature when the pressure of the air spray was 1.53 kg cm−2. Powder samples were gathered at the cyclone base and stored in sealed containers for further analysis, which was performed three times in every case.
2.2 Powder Analysis
The moisture content of Aloe vera gel without processing was determined using a thermo gravimetric method, by means of a thermo balance MB 300 (Brainweigh, USA). Moisture content of the powder (M) was determined using the vacuum drying oven method according to 920.151 (AOAC 1997).
Water activity (a w) was determined using Aqualab 4TE equipment (Decagon Devices, USA) from 1 g (0.035 oz) of the powder while maintaining a temperature of 24.5 ± 0.1 °C (Fang and Bhandari 2011).
2.3 Guggenheim–Anderson–De Boer Equation (GAB)
In order to understand the adsorption process of water by the amorphous powders, the GAB model (van den Berg and Bruins 1981) was applied to the experimental data using the linearized form expressed by Eq. (1):
where M is the moisture content (g of water/100 g of dry solid), a w is the water activity, M o is the theoretical water content of the monolayer, and C G and K G are energy constants relating to the temperature.
2.4 Glass Transition Temperature (T g)
Glass transition temperature of the powders was determined by a differential scanning calorimeter (Diamond, Perkin Elmer, USA) using 15 mg of sample powder in 20 μL sealed aluminum capsules and applying a temperature sweep from −20 to 120 °C and a heating rate of 20 °C/min (Ozmen and Langrish 2002). In order to understand the relationship between the glass transition temperature with different solid and moisture content (M), the Gordon and Taylor equation was applied (Gordon and Taylor 1952), as expressed by Eq. (2):
where T gm, T gs, and T gw are the mix, solids, and water glass transition temperatures, respectively, expressed in (°C); X s and X m are the solids and water weight fractions, respectively; and k is the Gordon and Taylor constant, which is related to the level of interaction between the system components. The model parameters (k and T gs) of Eq. (2) were estimated using a nonlinear regression analysis where T gw was −135 °C (Sablani et al. 2007; Welti-Chanes et al. 1999).
2.5 Statistical Analysis
The statistical significance of data was evaluated using the analysis of variance (ANOVA) analysis with α = 0.05. The statistical analysis was performed using the statistical program MINITAB, version 15 (Minitab, Inc, USA).
To verify the existence of two or more groups and mathematically differentiating between them, the normal distribution density function was used. Normal distribution is defined as a continuous variable distribution that is specified by two parameters: mean and standard deviation (Eq. 3):
where μ is the mean and σ is the standard deviation of the analyzed continuous variable. Densities were obtained for each of the relationships discussed: moisture content, water activity, and glass transition-moisture content.
3 Results and Discussion
3.1 Moisture Content (M) and Water Activity (a w)
M (kg of water/kg of dry solid) of gel powder showed values between 0.01 and 0.03 (kg of water/kg dry solids), with no significant difference found at a level of α = 0.05 for any of the obtained products under the different drying-air temperatures. These values are similar to those previously obtained for various powder products at different drying conditions (mucilage nopal, nopal juice, and acai pulp) (Tono et al. 2008; León et al. 2010). a w ranged from 0.18 to 0.30, without a clear relationship between inlet/outlet drying-air temperature effect and a w. Similar values of a w have been reported for other powder products, such as watermelon (0.20–0.29) (Quek et al. 2007), milk (0.2–0.6) (Laroche et al. 2005), and bayberry (0.1–0.3) (Fang and Bhandari 2011). For all Aloe vera gel powder samples, the existing relation between M and a w is observed in Fig. 1, and the existence of two different data groups is also identified in this figure. In the first group, which was called the low temperature group, samples were assessed using inlet/outlet temperatures of 200/70, 200/80, 200/90, 225/70, and 250/70 °C. These conditions correspond to all cases in which the lower inlet and three outlet temperatures were used, and also to the 225 and 250 °C temperature conditions, in which the lower outlet temperature was used. The second group, denoted as the high temperature group, had the samples with the lowest values of M and a w, and corresponded to the highest inlet/outlet drying-air temperatures (225/80, 225/90, 250/80, and 250/90 °C). When inlet temperatures of 200 °C and any outlet temperature were used, the M and a w values of the products were higher; at 225 and 250 °C inlet temperatures and 70 °C outlet temperature, materials were located within the low temperature drying groups. All conditions were grouped as high temperature.
3.2 Analysis of the GAB Equation Adjustment
Applying the GAB model to M and a w, the results showed that they can also be grouped into the low and the high temperature groups (Fig. 1). In the first case, it is possible that drying temperatures causes minor heat damage to the material; therefore, they could belong to the same isotherm, which may indicate that under these drying conditions, the original chemical composition of the material does not change significantly. The opposite could occur in the high temperature group, where the material may present different characteristics from those obtained at low temperatures. Therefore, they would be associated with different hygroscopic properties.
3.3 Glass Transition Temperature (T g)
Thermograms of product obtained under different drying conditions showed that T g ranged from 33 to 45 °C. These values match those reported for other similar material, such as maltodextrins (10–20 DE), where T g was reported to be in the range of 45.4–54.7 °C (Cai and Corke 2000). In addition, whole and pulp strawberry had a T g of 30 °C and a moisture content of 1.4 % (Moraga et al. 2004). Foster et al. (2006) reported that for lactose–glucose and lactose–fructose mixtures (both with a w = 0.23) a T g of 25 °C and 30 °C, respectively, and León et al. (2010) reported that spray dried nopal mucilage powder had a T g of 45 °C with 7.2 % moisture. In the literature, there are reports of different glass transition temperatures for different carbohydrates, such as mannose (31 °C), glucose (31 °C), galactose (32 °C), and sucrose (62 °C) (Bhandari and Howes 1999). Figure 2 shows the relationship of T g and M for the different powders obtained; even though a direct relationship between these properties could not be observed, it was possible to classify all obtained powders into groups identified. It has been suggested that Aloe gel powder remains in a vitreous state at room temperature, regardless of the drying-air temperature. Moreover, at higher temperatures and moisture levels, the plasticization effect can increases the loss of powder quality. The results experimentally obtained (M, a w, and T g) were analyzed using the Gordon and Taylor model (Eq. 2) to determine if exists any correlation between experimental values of water activity and glass transition. The results for all powders obtained at the different drying-air temperatures showed relatively low values of a w (0.18–0.33). The interval of water activity at which the samples are located is a narrow section of the values of water activity (0.1–0.9) which should cover the samples, as indicated in the analysis of the model of Gordon and Taylor. In this case, separation of the samples in the high and low temperature groups was also verified (Fig. 3).
4 Conclusions
In this study, the Aloe vera gel (without drying adjuvant) can be spray dried using an inlet drying-air temperature greater than or equal to 200 °C and the outlet drying-air temperatures from 70 to 90 °C, in a fountain type arrangement. The drying-air temperatures can be classified into high or low drying temperature groups according to changes in the values of M, a w, and T g properties of the powders obtained, and assessed through the normal distribution density function. The GAB equation and the Gordon–Taylor model are useful tools to identify the effects of the drying-air temperature on the physical properties of dehydrated material, as well as to categorize if a spray drying temperature is low or high.
However, it is important evaluate the prime thermolabile components of the gel, as well as the chemical changes observed, to achieve a better understanding of the relationship of these changes with the hygroscopic properties and transition phases of the powder product.
Abbreviations
- ANOVA:
-
Analysis of variance
- a w :
-
Water activity
- C G :
-
Energy constant relating to the temperature
- GAB:
-
Guggenheim-Anderson-De Boer equation
- K G :
-
Energy constant relating to the temperature
- μ :
-
Media of the analyzed continuous variable
- M :
-
Moisture content of the powder
- M o :
-
Theoretical water content of the monolayer
- T 1 :
-
Input temperatures
- T 2 :
-
Output temperatures
- T g :
-
Glass transition temperature
- T gm :
-
Mix glass transition temperature
- T gs :
-
Solids glass transition temperature
- T gw :
-
Water glass transition temperature
- X m :
-
Water weight fraction
- X s :
-
Solids weight fraction
- σ :
-
Standard deviation of the analyzed continuous variable
References
AOAC (1997) Official methods of analysis of AOAC International. Gaithersburg, Maryland
Bhandari BR, Howes T (1999) Implication of glass transition for the drying and stability of dried foods. J Food Eng 40:71–79
Bozzi A, Perrin C, Austin S, Arce-Vera F (2007) Quality and authenticity of commercial Aloe vera powders. Food Chem 103:22–30
Cai YZ, Corke H (2000) Production and properties of spray dried Amaranthus betacyanin pigments. J Food Sci 65:1248–1252
Eshun K, He Q (2004) Aloe vera: A valuable ingredient for the food, pharmaceutical and cosmetic industries—a review. Crit Rev Food Sci Nutr 44:91–96
Fang Z, Bhandari B (2011) Effect of spray drying and storage on the stability of bayberry polyphenols. Food Chem 129:1139–1147
Femenia A, García-Pascual P, Simal S, Roselló C (2003) Effects of heat treatment and dehydration on bioactive polysaccharide acemannan and cell wall polymers from Aloe barbadensis Miller. Carbohydr Polym 51:397–405
Filková I, Mujumdar AS (1999) Industrial spray drying systems. In: Mujumdar AS (ed) Handbook of industrial drying, 3rd edn. CRC, New York
Foster KD, Bronlund JE, Paterson AHJ (2006) Glass transition related cohesion of amorphous sugar powders. J Food Eng 77:997–1006
García SP, Mognetti C, Bello A, Martínez MJ (2010) Osmotic dehydration of Aloe vera (Aloe barbadensis Miller). J Food Eng 97:154–160
Gordon M, Taylor JS (1952) Ideal copolymers and the second order transitions of synthetic rubbers. I Noncrystalline copolymers. J Appl Chem 2:493–500
Gulia A, Sharma HK, Sarkar BC, Upadhyay A, Shitandi A (2010) Changes in physicochemical and functional properties during convective drying of Aloe vera (Aloe barbadensis) leaves. Food Bioprod Process 88:161–164
Hamman J (2008) Composition and Applications of Aloe vera leaf gel. Molecules 13:1599–1616
Laroche C, Fine F, Gervais P (2005) Water activity affects heat resistance of microorganisms in food powders. Int J Food Microbiol 97:307–315
León MFM, Méndez LLL, Rodríguez RJ (2010) Spray drying of mucilage (Opuntiaficus-indica): effects on powder properties and characterization. Carbohydr Polym 81:864–870
Masters K (1991) Spray drying handbook. Longman Scientific & Technical, New York
Miranda M, Maureira H, Rodríguez K, Vega-Gálvez A (2009) Influence of temperature on the drying kinetics, physicochemical properties, and antioxidant capacity of Aloe vera (Aloe barbadensis Miller) gel. J Food Eng 91:297–304
Moraga G, Martínez-Navarrete N, Chiralt A (2004) Water sorption isotherms and glass transition in strawberries: influence of pretreatment. J Food Eng 62:315–321
Nijdam JJ, Langrish TAG (2005) An investigation of milk powders produced by a laboratory-scale spray dryer. Dry Technol 23:1043–1056
Ozmen L, Langrish TAG (2002) Comparison of glass transition temperature and sticky point temperature for skim milk powder. Dry Technol 20:1177–1192
Peighambardoust SH, Golshan TA, Hesari J (2011) Application of spray drying for preservation of lactic acid starter cultures: a review. Trends Food Sci Technol 22:215–224
Quek Y, King N, Swedlund P (2007) The physicochemical properties of spray-dried watermelon powders. Chem Eng Process Process Intensif 46:386–392
Roustapour QR, Hosseinalipour M, Ghobadian L (2006) An experimental investigation of lime juice drying in a pilot plant spray dryer. Dry Technol 24:181–188
Sablani SS, Kasapis S, Rahman MS (2007) Evaluating water activity and glass transition concepts for food stability. J Food Eng 78:266–271
Simal S, Femenia A, Llull P, Roselló C (2000) Dehydration of Aloe vera: Simulation of drying curves and evaluation of functional properties. J Food Eng 43:109–114
Tono RV, Brabet C, Hubinger MD (2008) Influence of process conditions on the physicochemical properties of açai (Euterpe oleraceae Mart.) powder produced by spray drying. J Food Eng 88:411–418
van den Berg C, Bruins S (1981) Water activity and its estimation in food systems: theoretical aspects. In: Rockland LR, Stewart GF (eds) Water activity: influence on food quality. Academic, New York, pp 1–61
Vega MH, Góngora NMM, Barbosa CGV (2001) Advances in dehydration of foods. J Food Eng 49:271–289
Welti-Chanes J, Guerrero JA, Barcenas ME, Aguilera JM, Vergara F, Barbosa-Canovas GV (1999) Glass transition temperature (Tg) and water activity (aw) of dehydrated apple products. J Food Process Eng 22:91–101
Acknowledgements
The authors acknowledge the financial support of research projects: SIP 2011745, 20121173, 20111167, 20121754 and CONACyT 84287, as well as the PIFI-program, COFAA-IPN, Tecnológico de Monterrey and CONACyT for study grants.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2015 Springer Science+Business Media New York
About this chapter
Cite this chapter
García-Luna, I.N., Porras-Saavedra, J., Vergara-Balderas, F., Welti-Chanes, J., Gutiérrez-López, G.F., Alamilla-Beltrán, L. (2015). Defining High and Low Spray Drying Temperatures for Aloe vera Gel. In: Gutiérrez-López, G., Alamilla-Beltrán, L., del Pilar Buera, M., Welti-Chanes, J., Parada-Arias, E., Barbosa-Cánovas, G. (eds) Water Stress in Biological, Chemical, Pharmaceutical and Food Systems. Food Engineering Series. Springer, New York, NY. https://doi.org/10.1007/978-1-4939-2578-0_24
Download citation
DOI: https://doi.org/10.1007/978-1-4939-2578-0_24
Publisher Name: Springer, New York, NY
Print ISBN: 978-1-4939-2577-3
Online ISBN: 978-1-4939-2578-0
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)